HUMISEAL DIVISION -- HUMISEAL, 1C51
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CJJFB
MSDS NAME: HUMISEAL, 1C51
Responsible Party
Name: HUMISEAL DIVISION
Address: 26-60 BROOKLYN / QUEENS EXPRESSWAY WEST
City: WOODSIDE NY 11377
Info Phone: 718-932-0800
Emergency Phone Number: 800-424-9300 (CHEMTREC)
=======================================================
Ingredients
=======================================================
Name: *** PROPRIETARY ***
-----------------------------
=======================================================
Health Hazards Data
=======================================================
LD50 LC50 Mixture: UNKNOWN.
Route Of Entry Inds - Inhalation: NO
Skin: NO
Ingestion: NO
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: ACUTE: INGESTION/SKIN CONTACT/INHALATION: NONE KNOWN. EYE
CONTACT: MAY CAUSE MILD EYE IRRITATION. SUBCHRONIC (TARGET ORGAN) EFFECTS:
NONE KNOWN. THIS PRODUCT CONTAINS METHYPOLYSILOXANES WHICH CAN GENE RATE
FORMALDEHYDE AT APPROXIMATELY 300F (150C) AND ABOVE, IN ATMOSPHERES WHICH
CONTAIN OXYGEN. FORMALDEHYDE IS A SKIN AND RESPIRATORY SENSITIZER, EYE AND
THROAT IRRITANT, ACUTE TOXICANT, AND POTENTIAL CANCER HAZARD. AN MSDS FOR
FORMALDEHYDE IS AVAILABLE UPON REQUEST.
Explanation Of Carcinogenicity: THIS PRODUCT OR ONE OF ITS INGREDIENTS PRESENT
0.1% OR MORE IS NOT LISTED AS A CARCINOGEN OR SUSPECTED CARCINOGEN BY NTP,
IARC, OR OSHA.
Signs And Symptions Of Overexposure: SEE HEALTH HAZARDS.
Medical Cond Aggravated By Exposure: NONE KNOWN.
First Aid: INGESTION: NONE KNOWN. CALL MD IMMEDIATELY (FP N). SKIN: WASH WITH
SOAP AND WATER. INHALATION: NONE KNOWN. REMOVE TO FRESH AIR. SUPPORT
BREATHING (GIVE OXYGEN OR ARTIFICIAL RESPIRATION) (FP N). EYES: IMMEDIATELY
FLUSH WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES AND GET MEDICAL ATTENTION
IF IRRITATION PERSISTS. NOTE TO MD: NONE KNOWN.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: WASH WALKING SURFACES WITH DETERGENT AND WATER TO
REDUCE SLIPPING HAZARD. WEAR PROPER PROTECTIVE EQUIPMENT AS SPECIFIED IN THE
PROTECTICVE EQUIPMENT SECTION. WIPE, SCRAPE, OR SOAK UP IN AN INERT MATER IAL
AND PUT IN A CONTAINER INTENDED FOR FLAMMABLE MATERIALS FOR DISPOSAL.
Waste Disposal Methods: DISPOSAL SHOULD BE MADE IN ACCORDANCE WITH FEDERAL,
STATE, AND LOCAL REGULATIONS. INCINERATION RECOMMENDED IN APPROVED
INCINERATOR ACCORDING TO FEDERAL, STATE, AND LOCAL REGULATIONS.
Handling And Storage Precautions: DO NOT REUSE THIS CONTAINER. RELIEVE ANY
INTERNAL PRESSURE WHEN RECEIVED AND AT LEAST WEEKLY THEREAFTER BY SLOWLY
LOOSENING BUNG. RETIGHTEN BUNG IMMEDIATELY. AVOID CONTACT WITH EYES.
Other Precautions: KEEP CONTAINER CLOSED WHEN NOT IN USE TO PREVENT CONTACT
WITH ACIDIC, BASIC, OR OXIDIZING MATERIALS, AND METALLIC CATALYSTS LIKE TIN
SOAPS AND NOBLE METALS (PT, RH, ETC).
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: PMCC
Flash Point: >121.1C, 250.F
Extinguishing Media: ALL STANDARD FIREFIGHTING MEDIA.
Fire Fighting Procedures: NONE KNOWN. WEAR NIOSH APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT (FP N).
Unusual Fire/Explosion Hazard: SENSITIVITY TO MECHANICAL IMPACT: NO.
SENSITIVITY TO STATIC DISCHARGE: NOT EXPECTED.
=======================================================
Control Measures
=======================================================
Respiratory Protection: NONE KNOWN. USE NIOSH APPROVED RESPIRATOR APPROPRIATE
FOR EXPOSURE OF CONCERN (FP N).
Ventilation: NONE KNOWN.
Protective Gloves: CLOTH GLOVES.
Eye Protection: ANSI APPROVED CHEMICAL WORKERS GOGGLES (FP N).
Other Protective Equipment: NONE KNOWN. EYEWASH AND DELUGE SHOWER MEETING ANSI
DESIGN CRITERIA (FP N).
=======================================================
Physical/Chemical Properties
=======================================================
Boiling Point: >260.C, 500.F
Vapor Density: 1 (AIR=1)
Solubility in Water: INSOLUBLE
Appearance and Odor: HAZY LIQUID WITH SLIGHT ODOR.
Percent Volatiles by Volume: <2
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: PRODUCT GENERATES FLAMMABLE GAS ON CONTACT WITH
ACIDS, BASES, OR OXIDIZING MATERIALS.
Materials To Avoid: AVOID CONTACT WITH ACIDIC, BASIC, OR OXIDIZING AGENTS, AND
METALLIC CATALYSTS LIKE TIN SOAPS AND NOBLE METALS (PT, RH, ETC).
Hazardous Decomposition Products: CARBON MONOXIDE, CARBON DIOXIDE, SILICON
DIOXIDE, FLAMMABLE HYDROGEN GAS, FORMALDEHYDE.
Hazardous Polymerization Indicator: NO
=======================================================
Toxicological Information
=======================================================
Toxicological Information: ACUTE ORAL LD50 (MG/KG): UNKNOWN. ACUTE DERMAL LD50
(MG/KG): UNKNOWN. ACUTE INHALATION LC50 (MG/L): UNKNOWN. OTHER: NONE. AMES
TEST: UNKNOWN.
=======================================================
Ecological Information
=======================================================
Ecological: ECOTOXICOLOGICAL INFORMATION: NO DATA AT THIS TIME. CHEMICAL FATE
INFORMATION: NO DATA AT THIS TIME.
=======================================================
MSDS Transport Information
=======================================================
Transport Information: DOT SHIPPING NAME: N/A. DOT HAZARD CLASS: N/A. DOT
LABEL(S): N/A. UN/NA NUMBER: N/A. PLACARDS: NONE. IATA: N/A. IMO-IMDG-CODE:
N/A. EUROPEAN CLASS: RID (OCTI): N/A; ADR (ECE): N/A; RAR (AITA): N/A.
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: SARA SECTION 302: NONE FOUND. SARA (311, 312)
HAZARD CLASS: NONE. SARA (313) CHEMICALS: NONE.
Federal Regulatory Information: CPSC CLASSIFICATION: N/A. W HAZARD CLASS:
NON-CONTROLLED. W HAZARD CLASS: NON-CONTROLLED. W TRADE SECRET: NONE. EXPORT:
SCHDLE B/HTSUS: 3910.00.00003; ECCN: 1C96G. HAZARD RATING SYSTEMS: H
MIS/NFPA: FLAMMABILITY: 0; REACTIVITY: 1; HEALTH: 0.
State Regulatory Information: CALIFORNIA PROPOSITION 65: THIS PRODUCT IS NOT
APPROPRIATELY LABELED FOR USE OR SALE IN THE STATE OF CALIFORNIA.
=======================================================
Other Information
=======================================================
Other Information: PHYSICAL AND CHEMICAL PROPERTIES: ODOR THRESHOLD (PPM):
UNKNOWN; DENSITY (KG/M3): UNKNOWN; ACID/ALKALINITY (MEQ/G): UNKNOWN; VOC (EPA
METHOD 24) (G/L): NOT TESTED; SOLUBILITY IN ORGANIC SOLVENT (STATE SOLVENT):
UNKNOWN. THIS PRODUCT OR ITS COMPONENTS ARE ON THE EUROPEAN INVENTORY OF
EXISTING COMMERCIAL CHEMICALS (EINECS). IF SHIPMENT BY AIR IS REQUIRED, BE
CERTAIN THAT CONTAINER HAS NOT BEEN CONTA MINATED BY ACIDIC, BASIC, OR
OXIDIZING MATERIALS AND CONTAINER IS UNDAMAGED. DATE PRINTED: 30 JULY 1997.
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: HUMISEAL, 1C51
Company: HUMISEAL DIVISION/CHASE CORPORATION
Street: 26-60 BROOKLYN QUEENS EXPRESSWAY WEST
City: WOODSIDE NY
Zipcode: 11377
Health Emergency Phone: 800-424-9300 (CHEMTREC)
Label Required IND: Y
Date Of Label Review: 05/05/1999
Status Code: A
Origination Code: F
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: CAUTION
Respiratory Protection IND: YES
Health Hazard: None
Contact Hazard: Slight
Fire Hazard: Slight
Reactivity Hazard: None
Hazard And Precautions: ACUTE: INGESTION/SKIN CONTACT/INHALATION: NONE KNOWN.
EYE CONTACT: MAY CAUSE MILD EYE IRRITATION. SUBCHRONIC (TARGET ORGAN)
EFFECTS: NONE KNOWN. THIS PRODUCT CONTAINS METHYPOLYSILOXANES WHICH CAN GENE
RATE FORMALDEHYDE AT APPROXIMATELY 300F(150C) AND ABOVE, IN ATMOSPHERES WHICH
CONTAIN OXYGEN. FORMALDEHYDE IS A SKIN AND RESPIRATORY SENSITIZER, EYE AND
THROAT IRRITANT, ACUTE TOXICANT, AND POTENTIAL CANCER HAZARD. AN MSDS FOR
FORMALDEHYDE IS AVAILABLE UPON REQUEST.
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
PPD-2 FIXER SOLUTION, 23686
| 77-86-1
7757-79-1
110-15-6
288-32-4
87-69-4
7732-18-5 |
|
HUMISEAL, 1C51
| |
|
ENHANCED PRINT CARTRIDGE, 20K93130
| |
|
IPA-ANHYDROUS
| |
|
TEFLON TE6264 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6304N PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
LUBRIPLATE NO.130-A, NO. 130-AA
| |
|
TEFLON TE6467 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
MIL-C-10924F, SL-065
| |
|
FLAT BLACK, EFB534S0055
| 1317-65-3 |
|
PERMATEX(R) KLEAN 'N PRIME(TM) ACTIVATOR, 24163
| 67-64-1
75-28-5
149-57-5
22221-10-9
58823-74-8
7439-92-1
7440-02-0 |
|
N-1000 HIGH PURITY ANTI-SEIZE LUBRICANT, 51115-51117
| |
|
TEFLON TE6468 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6469 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
C-5A ANTISEIZE, ANTI-SEIZE LUBRICANT, 39614
| 7782-42-5
64742-52-5
7440-50-8
64742-18-3
14808-60-7
64755-01-7
64742-54-7 |
|
TEFLON TE6470 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
PXI HIGH STRENGTH RETAINING COMPOUND, 28649
| 24448-20-2
27813-02-1
39382-25-7
80-15-9
114-83-0
613-48-9
110-16-7
81-07-2
75-56-9
7440-38-2
7440-43-9
7439-92-1
7440-02-0 |
|
TEFLON TE6382 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
POTASH, SULFURATED, P624.31
| 39365-88-3 |
|
TEFLON TE6472 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6473 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6474 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6488 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6489 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE6490 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TE 6493 PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
TEFLON TG70J PTFE FLUOROPOLYMER RESIN
| 9002-84-0
7664-39-3
353-50-4 |
|
AMMONIUM OXALATE, 4% APHA, LC11280
| 6009-70-7
7732-18-5 |
|
MIL-L-2104F, 15W40
| |
|
STARTING FLUID CYLINDER
| |
|
NIKAL NUCLEAR
| |
|
VESSEL SOLUTION - PYRIDINE FREE, 27-910-05
| |
|
HI-CAT TM #85 CONVERTER FOR HIGH SOLIDS POLYURETHANE TOP COA
| 763-69-9
3779-63-3
822-06-0 |
|
IRON OXIDE, RED
| 1309-37-1 |
|
HYSOL EA 9309.3NA GAL SYSTEM PART B, P/N: AS9186018
| |
|
GRAY PRIMER, 2182 838
| |
|
HYSOL EA 9309.3NA GAL SYSTEM PART A, P/N: AS9186018
| |
|
ORIGINAL GLUE
| |
|
HYSOL EA 9309.3NA GAL SYSTEM PART A, P/N: AS9186018
| |
|
ENPLATE PC-475
| |
|
SEVOFLURANE, SEVOFRANE; ARGON
| |
|
ALCOSPERSE 602-N, 3015697-1-17-0
| |
|
ETHYLENE GLYCOL SOLUTION
| 107-21-1
7732-18-5 |
|
SILVER CONCENTRATE, S3140
| |
|
DIAZEPAM INJECTION,UPS
| 439-14-5 |
|
DESCALER
| 7664-38-2
7732-18-5 |
|
WEAK NITRIC ACID, GRADE 20.5
| 7697-37-2
7732-18-5 |
|
MIL-G-10924F (485539)
| |
|
RIGIDITE 2054 STRUCTURAL PREPREG
| |
|
SEALING COMPOUND; SC-0269 124
| 8020-83-5
8052-41-3
7429-90-5
14808-60-7
1317-65-3
1332-58-7
14807-96-6 |
|
|