CYTEC INDUSTRIES INC -- RIGIDITE 2054 STRUCTURAL PREPREG
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CJJSP
MSDS NAME: RIGIDITE 2054 STRUCTURAL PREPREG
Responsible Party
Name: CYTEC INDUSTRIES INC
Address: FIVE GARRET MOUNTAIN PLAZA
City: WEST PATERSON NJ 07424
Info Phone: 1-800-652-6013(US); 973-357-3193
Emergency Phone Number: 703-527-3887(OUTSIDE U.S. & CANADA)
Resp. Party Other MSDS No.: 7156
Preparer's Name: LARRY R. JOHNSON
Chemtrec IND/Phone: (800)424-9300
Proprietary Ind: Y
Review Ind: Y
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: CYTEC INDUSTRIES INC
Address: FIVE GARRET MOUNTAIN PLAZA
City: WEST PATERSON NJ 07424
Phone: 800-652-6013
=======================================================
Ingredients
=======================================================
Name: *** PROPRIETARY ***
-----------------------------
=======================================================
Health Hazards Data
=======================================================
LD50 LC50 Mixture: SEE INGREDIENTS.
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: YES
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: BASED ON THE PHYSICAL FORM OF THIS PRODUCT, OVEREXPOSURE
BY ORAL OR INHALATION ROUTE IS UNLIKELY. ALLERGIC SKIN REACTIONS OR PRIMARY
SKIN IRRITATION MAY BE PRODUCED BY PROLONGED OR REPEATED DERMAL CON TACT WITH
EPOXY RESINS. OVEREXPOSURE TO VAPOR DURING HEAT CURING MAY CAUSE IRRITATION
OR INJURY OF RESPIRATORY TRACT AND EYE IRRITATION. SEE TOXICOLOGICAL
INFORMATION.
Signs And Symptions Of Overexposure: SEE HEALTH HAZARDS.
First Aid: INGESTION: CALL MD IMMEDIATELY (FP N). EYES: IMMEDIATELY FLUSH WITH
POTABLE WATER FOR A MINIMUM OF 15 MINUTES, SEEK ASSISTANCE FROM MD (FP N).
SKIN: IMMEDIATELY WASH AFFECTED AREAS WITH SOAP & PLENTY OF WATER.
REMOVE CONTAMINATED CLOTHING & SHOES. OBTAIN MEDICAL ATTENTION. DESTROY
OR THOROUGHLY CLEAN SHOES BEFORE REUSE. DO NOT REUSE CONTAMINATED CLOTHING
WITHOUT LAUNDERING. INHALATION: MATERIAL IS NOT EXPECTED TO BE HARMFUL IF
INHALED. IF INHALED, REMOVE TO FRESH AIR.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: WHERE EXPOSURE LEVEL IS NOT KNOWN, WEAR NIOSH
APPROVED, POSITIVE PRESSURE, SELF-CONTAINED RESPIRATOR. WHERE EXPOSURE LEVEL
IS KNOWN, WEAR NIOSH APPROVED RESPIRATOR SUITABLE FOR LEVEL OF EXPOSURE. WEAR
SAME PROTECTIVE CLOTHING OR EQUIPMENT AS IN EXPOSURE CONTROLS/PERSONAL
PROTECTION SECTION. SWEEP UP SPILLS & PLACE IN A WASTE DISPOSAL
CONTAINER. FLUSH AREA WITH WATER.
Waste Disposal Methods: DISP MUST BE I/A/W FED, STATE & LOC REGS (FP N).
INFO ON RCRA WASTE CLASSIFICATION & DISP METHODOLOGY PROVIDED BELOW
APPLIES ONLY TO CYTEC PROD, AS SUPPLIED. IF MATL HAS BEEN ALTERED/CONTAM, OR
IT HAS EXCEEDED ITS REC SHELF LIFE, GUIDANCE MAY BE INAPPLIC. HAZ WASTE
CLASSIFICATION UNDER FED REGS (40 CFR PART 261 ET SEQ) IS DEPENDENT UPON
(SUPP DATA)
Handling And Storage Precautions: AVOID PROLONGED OR REPEATED CONTACT WITH
SKIN. FOOD, BEVERAGES & TOBACCO PRODUCTS SHOULD NOT BE CARRIED, STORED OR
CONSUMED WHERE THIS MATERIAL IS IN USE.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: CC
Flash Point: >100.C, 212.F
Autoignition Temp Text: N/AV
Extinguishing Media: USE WATER, CARBON DIOXIDE OR DRY CHEMICAL TO EXTINGUISH
FIRES.
Fire Fighting Procedures: USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT (FP N).
Unusual Fire/Explosion Hazard: NFPA HAZ RATING: HLTH: 2 (MATLS WHICH ON
INTENSE/CONTINUED EXPOS COULD CAUSE TEMPORARY INCAPACITATION/POSS RESIDUAL
INJURY UNLESS PROMPT MED TREATMENT IS GIVEN); FIRE: 1 (MATLS THAT MUST BE
PREHEATED BEFORE IGNIT CAN OCCUR); REACTIVITY: 0 (MATLS WHICH IN THEMSELVES
ARE NORMALLY STABLE, EVEN UNDER FIRE EXPOS (SUPP DATA)
=======================================================
Control Measures
=======================================================
Respiratory Protection: WHERE EXPOS ARE BELOW PEL, NO RESP PROT IS REQD. WHERE
EXPOS EXCEED PEL, USE NIOSH APPRVD RESP FOR MATL & LEVEL OF EXPOS. A
NIOSH APPRVD FULL FACEPIECE RESP WILL PROVIDE EYE & FACE PROT. CUTTING,
GRIN DING/SANDING OF PARTS FABRICATED AFTER CURING OF THIS MATL MAY CREATE
RESPIRABLE DUST PARTICLES. RESP PROT APPROP FOR THIS DUST MAY BE REQD. REFER
TO(SUPP DATA)
Ventilation: WHERE THIS MATL IS NOT USED IN A CLOSED SYSTEM, GOOD ENCLOSURE
& LOCAL EXHAUST VENT SHOULD BE PROVIDED TO CONTROL EXPOS WHEN
SPRAYING/CURING AT ELEVATED TEMPS.
Protective Gloves: IMPERVIOUS GLOVES; BARRIER CREAMS MAY BE USED IN CONJUNCTION
W/GLOVES (SUPDAT)
Eye Protection: ANSI APPROVED CHEMICAL WORKERS GOGGLES & FULL LENGTH FACESHIELD
(FP N).
Other Protective Equipment: ANSI APPROVED EYE WASH & DELUGE SHOWER (FP N).
PROTECTIVE CLOTHING SUCH AS IMPERVIOUS APRON, WORKPANTS, LONG SLEEVE WORK
SHIRT OR DISPOSABLE COVERALLS ARE RECOMMENDED TO PREVENT SKIN CONTACT.
Work Hygienic Practices: WASH THOROUGHLY AFTER HANDLING. BEFORE EATING,
DRINKING OR SMOKING, WASH FACE & HANDS WITH SOAP & WATER.
Supplemental Safety and Health: PHYSICAL/CHEM DATA:SATURATION IN AIR (% BY
VOL): N/A. EXPLO HAZ:CNDTNS & WHICH ARE NOT REACTIVE W/WATER). RESP
PROT:INGS FOR POTNTL HAZ COMPONENTS IN DUST. SEE "GUIDE TO INDUS RESP PROT"
(NIOSH). PROT GLOVES:TO PROVIDE ADDNL SKIN PROT. WASTE DISP METH:WHETHER
MATL IS RCRA "LISTED HAZ WASTE" OR HAS ANY OF (OTHER INFO)
=======================================================
Physical/Chemical Properties
=======================================================
M.P/F.P Text: NOT AVAILABLE
Decomp Text: NOT AVAILABLE
Spec Gravity: 1.7-2.0
PH: NOT AVAILABLE
Evaporation Rate & Reference: NEGLIGIBLE
Solubility in Water: NEGLIGIBLE
Appearance and Odor: TAN VISCOUS LIQUID ON WHITE CARRIER; NO ODOR.
Percent Volatiles by Volume: <1.0 (WT)
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: NONE KNOWN.
Materials To Avoid: NONE KNOWN.
Hazardous Decomposition Products: CARBON MONOXIDE, CARBON DIOXIDE, OXIDES OF
NITROGEN.
Hazardous Polymerization Indicator: YES
Conditions To Avoid Polymerization: AVOID CONTACT WITH ACIDS, BASES OR AMINES.
DO NOT HEAT MATERIAL ABOVE 120F (48.9C).
=======================================================
Toxicological Information
=======================================================
Toxicological Information: PROD: ACUTE:LD50:(DERMAL,RABBIT) >2000 MG/KG.
COMPONENTS: AMORPHOUS SILICA: ACUTE 4-HR INHAL LC50 (RAT) IS >0.25 MG/L
(MAX ATTAINABLE CONC). OVEREXP TO SYNTHETIC AMORPHOUS SILICA DUST BY INHAL,
ABSORP TION/INGEST IS NOT EXPECTED TO CAUSE ADVERSE EFTS. AMORPHOUS SILICA
DOES NOT CAUSE LUNG DISEASES THAT CRYSTALLINE SILICA IS KNOWN TO FORM.
ACETONE: ACUTE DERMAL (RABBIT) LD50 VALUE OF 20 G/KG. LC50 (R AT) FOR ACETONE
VAP AFTER 4 HR EXPOS IS 16,000 PPM (37.95 MG/L). CHRONIC OVEREXP TO VAP MAY
CAUSE DRYNESS OF MOUTH, HDCH, DIZZ, NAUS & LOSS OF COORD. LIQ ACETONE IS
SEVERELY IRRIT TO EYES & MILDLY IRR IT TO SKIN. FIBERGLASS IS (OTHER
INFO)
=======================================================
Ecological Information
=======================================================
Ecological: NO AQUATIC LC50, BOD/COD DATA AVAIL. OCTANOL/H*2O PARTITION COEF:
N/A. -- OTHER INFO:FIGHTING MEASURES SECTION OF THIS MSDS (FLASH POINT). FOR
CORROSIVITY, SEE PHYSICAL & CHEM PROPERTIES & TRANSPORT I NFO
SECTIONS (PH & DOT CORROSIVITY). FOR REACTIVITY, SEE STABILITY &
REACTIVITY SECTION (INCOMPAT MATLS). FOR TOX, SEE INGS SECTION (COMPOSITION).
FED REGS ARE SUBJECT TO CHANGE. STATE & LOC REQUIREME NTS, WHICH MAY
DIFFER FROM/BE MORE STRINGENT THAN FED REGS, MAY ALSO APPLY TO CLASSIFICATION
OF MATL IF IT IS TO BE DISPOSED. CYTEC ENCOURAGES RECYCLE, RECOVERY &
REUSE OF MATLS, WHERE PERMITTED, AS A N ALTERNATE TO (STATE REGULATORY INFO)
=======================================================
MSDS Transport Information
=======================================================
Transport Information: REFER TO APPROP TRANSPORTATION REGS FOR SPECIFIC
REQUIREMENTS. SHIPPING INFO: DOT, IMO, ICAO/IATA, TRANSPORT CANADA -
SHIPPING NAME: NOT APPLIC/NOT REGULATED; HAZ CLASS/PACKING GRP: N/A; UN/ID
NUMBER : N/A; TRANSPORT LBL REQD: NONE REQD. DOT, IMO - IMDG PG: N/A; DOT HAZ
SUBSTANCES (PROD RQ): N/A. ICAO/IATA, TRANSPORT CANADA - HAZ CLASS: N/A;
SUBSIDIARY CLASS: N/A; PACKING INSTR (PASSENGER/CARGO): N/A. MAX NET QTY
(PASSENGER/CARGO): N/A. TECHNICAL NAME( N.O.S.): N/A.
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: ACETONE IS NOT SUBJECT TO REPORTING REQUIREMENTS
PURSUANT TO SECTION 313 OF CERCLA (40 CFR 372). PRODUCT CLASSIFICATION UNDER
SECTION 311 OF SARA: ACUTE: Y; CHRONIC: N; FIRE: N; REACTIVE: N; PRESSURE:
N.
Federal Regulatory Information: ACETONE MAY BE SUBJECT TO REPORTING
REQUIREMENTS PURSUANT TO SECTION 12(B) OF TSCA, OR MAY BE SUBJECT TO RELS
REPORTING REQUIREMENTS (40 CFR 307, 40 CFR 311, ETC). ACETONE - 67-64-1 -
<1.0%: TPQ(LBS): NONE; RQ(LBS): 5000. TSCA 12B: YES. U.S. TSCA: THIS PROD
IS CONSIDERED ARTICLE & IS THEREFORE EXCLUDED BY DEFINITION FROM
REQUIREMENTS OF TOX SUBSTANCES CONTROL ACT, 15 U.S.C. 2601 ET. SEQ. CANADA DS
L: THIS PROD IS AN ARTICLE & I/A/W SUBSECTION 3 OF CANADIAN ENVIRON PROT
ACT ITS COMPONENTS ARE EXEM PT FROM REPORTING REQUIREMENTS FOR DOMESTIC
SUBSTANCES LIST. EEC EINECS: THIS PROD, BECAUSE IT IS AN ARTICLE OF (STATE
REGULATORY INFO)
State Regulatory Information: FED REGULATORY: COMMERCE, IS EXEMPT FROM
PROVISIONS OF DIRECTIVE 67/548/EEC, AMENDED 79/831/33C. -- ECOLOGICAL
INFO:DISP AS WASTE. CYTEC RECS THAT ORGANIC MATLS CLASSIFIED AS RCRA HAZ
WASTES BE DISPOS ED OF BY THERMAL TREATMENT/INCIN AT EPA APPRVD FACILITIES.
CYTEC HAS PROVIDED FOREGOING FOR INFO ONLY; THE PERSON GENERATING WASTE IS
RESPONSIBLE FOR DETERMINING WASTE CLASSIFICATION & DISPOSAL METHOD .
=======================================================
Other Information
=======================================================
Other Information: TOX INFO:CONSIDERED NUISANCE PARTICULATE WHICH WILL NOT
CAUSE ADVERSE HLTH EFTS OTHER THAN RESP CONGESTION/IRRIT. PRLNG/RPTD EXPOS TO
EPOXY RESINS MAY PRDCE ALLERGIC SKIN RXNS & PRIMARY SKIN IRRIT. SU PP
DATA:FOUR RCRA "HAZ WASTE CHARACTS."REFER TO 40 CFR PART 261.33 TO DETERMINE
IF A GIVEN MATL TO BE DISPOSED OF IS RCRA "LISTED HAZ WASTE"; INFO CONTAINED
IN SECTION 15 OF THIS MSDS IS NOT INTENDED TO INDICATE IF PROD IS "LISTED
HAZ WASTE." RCRA HAZ WASTE CHARACT. THERE ARE 4 CHARACTS DEFINED IN 40 CFR
SECTION 261.21-61.24; IGNITABILITY, CORROSIVITY, REACTIVITY & TOXICITY.
TO DETERMINE IGNITABIL ITY, SEE FIRE (ECOLOGICAL INFO)
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: RIGIDITE 2054 STRUCTURAL PREPREG
Company: CYTEC INDUSTRIES INC
Street: FIVE GARRET MOUNTAIN PLAZA
City: WEST PATERSON NJ
Zipcode: 07424
Health Emergency Phone: 703-527-3887(OUTSIDE U.S. & CANADA)
Label Required IND: Y
Date Of Label Review: 08/02/1999
Status Code: A
Origination Code: F
Chronic Hazard IND: Y
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: CAUTION
Respiratory Protection IND: YES
Health Hazard: None
Contact Hazard: Slight
Fire Hazard: Slight
Reactivity Hazard: None
Hazard And Precautions: ACUTE: BASED ON THE PHYSICAL FORM OF THIS PRODUCT,
OVEREXPOSURE BY ORAL OR INHALATION ROUTE IS UNLIKELY. OVEREXPOSURE TOVAPOR
DURING HEAT CURING MAY CAUSE IRRITATION OR INJURY OF RESPIRATORY TRACT AND
EYE IRRITATION. CHRONIC: ALLERGIC SKIN REACTIONS OR PRIMARY SKIN IRRITATION
MAY BE PRODUCED BY PROLONGED/REPEATED DERMAL CONTACT WITH EPOXY RESINS.
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|