IOWA PAINT MFG INC -- 18416 LF GRY RUST/INH EPOXY PR
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CKXHY
MSDS NAME: 18416 LF GRY RUST/INH EPOXY PR
Responsible Party
Name: IOWA PAINT MFG CO INC
Address: 17TH & GRAND
City: DES MOINES IA 50305-5000
Info Phone: 515-283-1501
Emergency Phone Number: 515-283-1501
Review Ind: Y
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: IOWA PAINT MFG CO INC
Address: 17TH & GRAND
City: DES MOINES IA 50305-5000
Phone: 515-283-1501
=======================================================
Ingredients
=======================================================
Cas: 13463-67-7
RTECS #: XR2275000
Name: TITANIUM DIOXIDE
Percent by Wt: 7.02
ACGIH TLV: 10 MG/M3
ACGIH STEL: NOT ESTABLISHED
------------------------------
Cas: 14807-96-6
RTECS #: WW2710000
Name: TALC
Percent by Wt: 10.1
ACGIH TLV: 2 MG/M3
ACGIH STEL: NOT ESTABLISHED
------------------------------
Cas: 100-41-4
RTECS #: DA0700000
Name: ETHYLBENZENE
Percent by Wt: 8.12
ACGIH TLV: 100 PPM
EPA Rpt Qty: 1000 LBS
DOT Rpt Qty: 1000 LBS
------------------------------
Name: ZINC COMPOUND
Percent by Wt: 3.22
-----------------------------
Name: BARIUM COMPOUND
Percent by Wt: 2.72
ACGIH TLV: .50 MG/M3
-----------------------------
Cas: 95-63-6
RTECS #: DC3325000
Name: 1,2,4-TRIMETHYLBENZENE
Percent by Wt: 1.65
------------------------------
Cas: 64742-95-6
RTECS #: WF3400000
Name: SC-100 SOLVENT
Percent by Wt: 3.27
ACGIH TLV: 50 PPM
------------------------------
Cas: 1330-20-7
RTECS #: ZE2100000
Name: XYLOL
Percent by Wt: 36.88
EPA Rpt Qty: 1000 LBS
DOT Rpt Qty: 1000 LBS
------------------------------
Cas: 1317-95-9
RTECS #: VV7336000
Name: QUARTZ
Percent by Wt: .6
OSHA PEL: SEE TABLE Z-3
ACGIH TLV: 0.1 MG/M3
ACGIH STEL: NOT ESTABLISHED
------------------------------
Cas: 7440-66-6
RTECS #: ZG8600000
Name: ZINC AS ZN
Percent by Wt: 2.58
EPA Rpt Qty: 1000 LBS
DOT Rpt Qty: 1000 LBS
------------------------------
Cas: 7440-39-3
RTECS #: CQ8370000
Name: BARIUM AS BA
Percent by Wt: 1.41
ACGIH TLV: 0.5 MG/M3
ACGIH STEL: NOT ESTABLISHED
=======================================================
Health Hazards Data
=======================================================
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: YES
Carcinogenicity Inds - NTP: YES
IARC: YES
OSHA: NO
Signs And Symptions Of Overexposure: ACUTE: INHALATION: IRRITATION OF
RESPIRATORY TRACT AND/OR ACUTE NERVOUS SYSTEM DEPRESSION, CHARACTERIZED BY
HEADACHE, DIZZINESS, STAGGERING GAIT, CONFUSION, UNCONSCIOUSNESS OR COMA.
SKIN/EYE: MAY CAUS E MODERATE SKIN OR EYE INJURY. INGESTION: IRRITATION OF
MUCOUS MEMBRANES & GASTROINTESTINAL TRACT. CHRONIC: INHALATION: REPORTS
HAVE ASSOCIATED PROLONGED & REPEATED OCCUPATIONAL OVEREXPOSURE TO SOLVEN
TS W/ PERMANENT BRAIN & NERVOUS SYSTEM DAMAGE. MAY CAUSE INJURY TO THE
LIVER, KIDNEY, BONE MARROW & BLOOD CELLS. SKIN: MAY CAUSE DERMATITIS AND
DEFATTING OF THE SKIN.
First Aid: INHALATION: REMOVE FROM EXPOSURE. RESTORE BREATHING. KEEP WARM AND
QUIET. EYES: FLUSH IMMEDIATELY WITH COPIOUS QUANTITIES OF WATER FOR AT LEAST
15 MINUTES. SKIN: WASH AFFECTED AREAS WITH SOAP AND WATER. REMOVE
CONTAMINATED CLOTHING. INGESTION: IF SWALLOWED, DO NOT INDUCE VOMITING. IN
ALL CASES, SEEK IMMEDIATE MEDICAL ATTENTION!
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: REMOVE ALL SOURCES OF IGNITION. AVOID BREATHING
VAPORS. VENTILATE AREA. REMOVE WITH INERT ABSORBENT AND NON-SPARKING TOOLS.
Waste Disposal Methods: DISPOSE IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL
REGULATIONS. INCINERATE IN APPROVED FACILITY. DO NOT INCINERATE CLOSED
CONTAINERS.
Handling And Storage Precautions: DO NOT STORE ABOVE 120 F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA, CLASS I,
FLAMMABLE LIQUIDS.
Other Precautions: KEEP OUT OF THE REACH OF CHILDREN. DO NOT TAKE INTERNALLY.
CONTAINERS SHOULD BE GROUNDED WHEN POURING. AVOID FREE FALL OF LIQUID IN
EXCESS OF A FEW INCHES. NEVER FLAME CUT, BRAZE, OR WELD EMPTY PAINT
CONTAINERS, OR PAINTED SURFACES BEFORE THOROUGHLY DRY.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: TCC
Flash Point Text: 80-85 F
Lower Limits: 1.0
Extinguishing Media: USE NFPA CLASS B EXTINGUISHERS (CARBON DIOXIDE, DRY
CHEMICAL OR FOAM) DESIGNED TO EXTINGUISH NFPA CLASS I LIQUID FIRES.
Fire Fighting Procedures: DO NOT USE WATER EXCEPT FOR COOLING CLOSED CONTAINERS
TO PREVENT PRESSURE BUILD-UP AND EXPLOSION WHEN EXPOSED TO EXTREME HEAT. USE
FOG NOZZLES IF WATER IS USED. FIREFIGHTERS SHOULD BE EQUIPPED WITH MASKS
AND SELF-CONTAINED RESPIRATORS.
Unusual Fire/Explosion Hazard: KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE FROM
HEAT, NON-EXPLOSION PROOF ELECTRICAL EQUIPMENT, SPARKS AND OPEN FLAME.
CLOSED CONTAINER MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT. DO NOT APPLY TO
VERY H OT SURFACES.
=======================================================
Control Measures
=======================================================
Respiratory Protection: IN OUTDOOR OR OPEN AREAS, USE NIOSH/MSHA APPROVED
MECHANICAL FILTER RESPIRATOR TO REMOVE SOLID AIRBORNE PARTICLES OF OVERSPRAY
DURING SPRAY APPLICATION. IN RESTRICTED VENTILATION AREAS, USE NIOSH/MSHA
APPROVED CHEMICAL-MECHANICAL FILTERS, DESIGNED TO REMOVE A COMBINATION OF
PARTICULATE, GAS AND VAPOR.
Ventilation: PROVIDE GENERAL DILUTION OR LOCAL EXHAUST VENTILATION IN VOLUME
& PATTERN TO KEEP TLV OF MOST HAZARDOUS INGREDIENTS BELOW TLV LEVEL.
Protective Gloves: REQUIRED FOR PROLONGED OR REPEATED CONTACT.
Eye Protection: USE SAFETY EYEWEAR TO PROTECT AGAINST SPLASH OF LIQUID.
Other Protective Equipment: PREVENT PROLONGED SKIN CONTACT TO CONTAMINATED
CLOTHING.
Supplemental Safety and Health: WT/GAL 9.7-10.0
=======================================================
Physical/Chemical Properties
=======================================================
B.P. Text: 277-342 F
Vapor Density: >AIR
Evaporation Rate & Reference: SLOWER THAN ETHER
Percent Volatiles by Volume: 49.94
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: AVOID EXTREME HEAT.
Materials To Avoid: ISOLATE FROM STRONG OXIDIZERS SUCH AS PERMANGANATE.
Hazardous Decomposition Products: NONE
Hazardous Polymerization Indicator: NO
Conditions To Avoid Polymerization: NONE
=======================================================
Toxicological Information
=======================================================
=======================================================
Ecological Information
=======================================================
=======================================================
MSDS Transport Information
=======================================================
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: THE FOLLOWING INGREDIENTS ARE SUBJECT TO THE
REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND COMMUNITY
RIGHT-TO-KNOW ACT OF 1986: ETHYLBENZENE, ZINC COMPOUND, BARIUM COMPOUND, (1,2
,4-TRIMETHYL BENZENE), XYLOL.
=======================================================
Other Information
=======================================================
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: 18416 LF GRY RUST/INH EPOXY PR
Company: IOWA PAINT MFG CO INC
Street: 17TH & GRAND
City: DES MOINES IA
Zipcode: 50305-5000
Health Emergency Phone: 515-283-1501
Label Required IND: Y
Date Of Label Review: 01/04/2001
Status Code: A
Origination Code: G
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
MEK FREE HI-PERF THINNER
| 1330-20-7
111-76-2
100-41-4
108-65-6 |
|
FLOOR & PORCH ENAMEL GRAY
| 108-65-6
1309-37-1
13463-67-7
64742-95-6
8052-41-3
1332-58-7
1317-65-3
96-29-7 |
|
WELD-ON P-70 PRIMER FOR PVC AND CPVC PLASTIC PIPE
| |
|
PSX 700 CURE, 700C00000
| |
|
PROF/FLAT WALL FINISH P-B
| 107-21-1
25265-77-4
1317-65-3
14808-60-7
7631-86-9
13463-67-7 |
|
GLOSS ALKYD WHITE
| 96-29-7
64741-65-7
64742-88-7
13463-67-7 |
|
S/GL ALKYD ENAMEL DEEP BS
| 96-29-7
1332-58-7
64741-65-7
8052-41-3
1317-65-3
13463-67-7 |
|
MOLYSULFIDE
| 1317-33-5 |
|
849 8578,KODAK PROFESSIONAL EI MAGENTA (SEE SUPPL DATA)
| |
|
SHIELD PRE-CLEAN 2000
| 68391-01-5
68956-79-6
14808-60-7 |
|
833 8758,KODAK PROFESSIONAL EI BLACK (SEE SUPPL DATA)
| |
|
FASMETAL RESIN, 0136
| 25068-38-6 |
|
PLASTIC STEEL PUTTY (A) RESIN, 0100
| 25068-38-6 |
|
SILVER-COPPER-PHOSPHORUS BRAZING ALLOYS
| 7440-50-8
7723-14-0
7440-22-4 |
|
OUTPUT ACTIVATOR, 17100, PART OF KIT 00241
| 71-55-6
68411-20-1
109-87-5
67-63-0
13395-16-9 |
|
PHILLYCLAD 620 TAILSHAFT HARDENER
| |
|
DIPAK E-2888A
| 9042-82-4 |
|
DIPAK E-2888B
| |
|
3M TYPE 648 TONER, 78696986336
| 25767-47-9
27136-15-8
1333-86-4
8005-02-5
1317-38-0
9003-07-0 |
|
ZX1000X, LASER TYPE TONER
| |
|
CONDUCTIVE GREASE AND ANTI-OXIDANT, 19-820
| |
|
"ZYTEL" NYLON RESINS IN SYNONYM LIST OF ZYT022
| 32131-17-2 |
|
40-3905 RESIN
| |
|
3694 SATIN ACRI HSE PNT - MTB
| 1317-65-3
13463-67-7
14807-96-6
107-21-1
29911-28-2 |
|
302 SEMIGLOSS ALKYD
| 8052-41-3
1317-65-3
13463-67-7
1332-58-7
64742-88-7
64742-95-6
96-29-7 |
|
302 SEMIGLOSS ALKYD
| 13463-67-7
96-29-7
1332-58-7
14807-96-6
8032-32-4 |
|
950 SUPER RED BARN PAINT
| 8052-41-3
1317-65-3
96-29-7
14807-96-6
64741-65-7
1309-37-1 |
|
4396 CLEAR STAIN BASE
| 8052-41-3
1317-65-3
96-29-7
64742-95-6
64741-65-7
95-63-6
7440-48-4 |
|
GARD ANTI RUST SAE 15W-40
| |
|
46815 FLOOR ENAMEL GRAY
| 8052-41-3
1317-65-3
1332-58-7
13463-67-7
64742-95-6
7440-48-4 |
|
970 HSE AND BARN ACRY FLT RED
| 1317-65-3
107-21-1
25265-77-4
1309-37-1
12001-26-2
1332-09-8 |
|
2202 APT FLAT LATEX WALL PAINT
| 1317-65-3
107-21-1
1332-58-7
13463-67-7
1317-95-9 |
|
18416 LF GRY RUST/INH EPOXY PR
| 13463-67-7
14807-96-6
100-41-4
95-63-6
64742-95-6
1330-20-7
1317-95-9
7440-66-6
7440-39-3 |
|
47192 SEMIGLS ALKYD EN FED TAN
| 13463-67-7
64742-95-6
96-29-7
1332-58-7
8052-41-3
1317-65-3
1309-37-1 |
|
LB 1132-21
| |
|
SHIPPING MATE CASE SEALING ADHESIVE
| |
|
SHIPPING-MATE PALLETIZING ADHESIVE
| |
|
CHRISTO-LUBE MCG III
| 69991-61-3
9002-84-0 |
|
SCOTCHPLY SP-381
| |
|
OZZY JUICE (SW-3 TRUCK GRADE DEGREASING SOLUTION)
| |
|
PUTTY HARDENER 0200; 10050, 10080, 10110, 10110G,10120
| 112-24-3
25154-52-3
140-31-8
68082-29-1 |
|
PUTTY HARDENER, 10130, 10260, 10610, 10620
| 112-24-3
25154-52-3
140-31-8
68082-29-1 |
|
PUTTY HARDENER, 10650, 11410, 11420, DE087
| 112-24-3
25154-52-3
140-31-8
68082-29-1 |
|
90059-5, ACIDCLEAN FR
| |
|
PSX 700 BLACK RESIN, 700B90000
| |
|
AERO KLEEN AVIATION SOLVENT
| |
|
SAFE CARE MORE THAN GLASS (READY TO USE)
| |
|
8801K22/MS35058-22
| |
|
MOLSIV ADSORBENTS 13X HP 20X40
| 7631-86-9
1344-28-1
1313-59-3
1309-48-4 |
|
UNIVERSAL PLUS 3%/ 6% FIRE FIGHTING FOAM CONCENTRATE AR-AFFF
| |
|
|