===================== Product Identification =====================
MSDS NAME:MIL-C-22750D EPOXY GREEN 34087 (1-1G-114)
NIIN:00N011380
MSDS Number: BHZDC
=== Responsible Party ===
Company:CROWN METRO AEROSPACE COATINGS INC,(SUP DATA)
Address:4343 TEMPLE CITY BLVD
City:TEMPLE CITY
State:CA
ZIP:91780-4293
Country:US
Info Phone Num:818-579-6270
Emergency Phone Num:818-579-6270
CAGE:CROME
=== Contractor Identification ===
Company:ADVANCED PRODUCTS DBA ADVANCED COATINGS & CHEMICAL
Address:4343 TEMPLE CITY BLVD
Box:City:TEMPLE CITY
State:CA
ZIP:91780-4229
Country:US
Phone:818-579-6270
CAGE:51686
Company:CROWN METRO AEROSPACE COATINGS INC
Box:5695
City:GREENVILLE
State:SC
ZIP:29606
Country:US
Phone:803-277-1870
CAGE:CROME
============= Composition/Information on Ingredients =============
Name:CARBON BLACK
CAS:1333-86-4
RTECS #:FF5800000
Other REC Limits:N/K
OSHA PEL:3.5 MG/M3
ACGIH TLV:3.5 MG/M3; 9192
Name:TITANIUM DIOXIDE
CAS:13463-67-7
RTECS #:XR2275000
Other REC Limits:N/K
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST; 9293
Name:AMORPHOUS SILICA.ACGIH TLV FOR TOTAL DUST CONTAINING NO
ASBESTOS & <1% CRYSTALLINE SILICA.
CAS:112945-52-5
RTECS #:VV7310000
Other REC Limits:N/K
OSHA PEL:6 MG/M3
ACGIH TLV:10 MG/M3 TOTAL DUST
Name:METHYL N-AMYL KETONE
CAS:110-43-0
RTECS #:MJ5075000
Other REC Limits:N/K
OSHA PEL:100 PPM
ACGIH TLV:50 PPM; 9192
Name:TOLUENE (SARA III)
CAS:108-88-3
RTECS #:XS5250000
Other REC Limits:N/K
OSHA PEL:200 PPM/150 STEL
ACGIH TLV:50 PPM; 9293
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:N-BUTYL ACETATE (SARA III)
CAS:123-86-4
RTECS #:AF7350000
Other REC Limits:N/K
OSHA PEL:150 PPM/200 STEL
ACGIH TLV:150 PPM/200STEL;9192
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS
Name:ISOPROPYL ALCOHOL (SARA III)
CAS:67-63-0
RTECS #:NT8050000
Other REC Limits:N/K
OSHA PEL:400 PPM/500 STEL
ACGIH TLV:400 PPM/500STEL;9192
Name:EPOXY RESIN
CAS:25068-38-6
RTECS #:KC2100000
Other REC Limits:10 MG/M3
OSHA PEL:N/K
ACGIH TLV:N/K
Name:YELLOW OXIDE.OSHA PEL FOR DUST & FUME TOTAL PARTICULATE.
CAS:12259-21-1
Other REC Limits:N/K
OSHA PEL:10 MG(FE)/M3
ACGIH TLV:5 MG(FE)/M3 FUME
===================== Hazards Identification =====================
LD50 LC50 Mixture:N/K
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGESTION:DAMAGE TO THROAT AND
ESOPHAGUS;CHEMICAL PNEUMONITIS AND PULMONARY EDEMA.POSSIBLE KIDNEY
AND LIVER IMPAIRMENT.SKIN SENSITIZATION,DERMATITIS.CONJUNCTIVITIS.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:EYES:CAN CAUSE SEVERE
IRRITATION,REDNESS,TEARING,BLURRED VISION,CONJ.SKIN:PRLNG/RPTD
CONTACT CAN CAUSE IRRIT.DEFATTING.SENSIT,DERMAT.INGEST:DAMAGE TO
THROAT,ESOPHAGUS.VOMITING,DIARRHEA.POSS KIDNEY/LIV ER
IMPAIRMENT.INHAL:DIZZINESS,BREATHINGDIFFICULTY,HEADACHES,LOSS OF
COORDINATION.ASTHMA-LIKE SYMPTOMS,CNS EFFECTS.
Medical Cond Aggravated by Exposure:ASTHMA,RESPIRATORY TRACT
IRRITATION,DERMATITIS,KIDNEY & LIVER PROBLEMS,CONJUNCTIVITIS.
======================= First Aid Measures =======================
Eyes:FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15
MINUTES.SKIN:WASH THOROUGHLY WITH SOAP AND WATER.SEE A
DOCTOR.INGESTION:DO NOT INDUCE VOMITING.CAN CAUSE CHEMICAL
PNEUMONITIS & PULMONARY EDEMA.C ONTACT PHYSICIAN
IMMEDIATELY.INHALATION:MOVE PERSON TO FRESH AIR.IF BREATHING
STOPS,APPLY ARTIFICIAL RESPIRATION & SEEK IMMEDIATE MEDICAL
ATTENTION.
===================== Fire Fighting Measures =====================
Flash Point Method:TCC
Flash Point:40F,4C
Lower Limits:12.0%
Upper Limits:1.11%
Extinguishing Media:FOAM,DRY CHEMICAL,CO*2,WATER FOG.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:IRRITATING/TOX GASES/SMOKE PRESENT FROM
DECOMP.KEEP FROM HEAT,SPARKS,OPEN FLAMES.CLSD CONTR MAY BURST IN
EXTREME HEAT.VAPOR FORMS EXPLO MIX IN AIR (SEE SUPP)
================== Accidental Release Measures ==================
Spill Release Procedures:ELIMINATE IGNITION SOURCES;PROVIDE GOOD
VENTILATION;DIKE SPILL AREA & ADD ABSORBENT MATERIAL TO SPILLED
LIQUID.THOROUGHLY WET WITH WATER AND MIX.
Neutralizing Agent:N/K
====================== Handling and Storage ======================
Handling and Storage Precautions:USE NON-SPKING UTENSILS IN
HANDLING.AVOID HOT METAL SURF.USE IN COOL,WELL-VENTED AREAS.KEEP
CONTR CLSD IF NOT IN USE.KEEP FROM EXCESS HEAT/OPEN FLAME.
Other Precautions:PROHIBIT SMOKING IN USE AREA.USE ALUMINUM,BRASS OR
COPPER TOOLS.DO NOT USE PLASTIC TOOLS.EMPTY CONTR RETAINS PRODUCT
RESIDUES (VAPOR/LIQUID/SOLID),OBSERVE ALL HAZARD PRECAUTIONS.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR
EXPOSURE OF CONCERN .
Ventilation:LOCAL AND GENERAL VENTILATION NECESSARY TO KEEP AIR
CONCENTRATION BELOW TLV .USE EXPLOSION-PROOF EQUIPMENT.
Protective Gloves:IMPERMEABLE CHEMICAL HANDLING.
Eye Protection:CHEM WORK GOGGLES & FACESHIELDS.
Other Protective Equipment:USE IMPERMEABLE APRONS & PROTECTIVE
CLOTHING.HEAD CAP USE STRONGLY RECOMMENDED.EYE WASHES & SAFETY
SHOWERS.
Work Hygienic Practices:EYE WASHES AND SAFETY SHOWERS IN WORK PLACE
RECOMMENDED.
Supplemental Safety and Health
EXPLO HAZ:BETWEEN UPPER/LOWER EXPLOSIVE LIMITS.HAZ DECOMP
PROD:CO,CO*2,NITROGEN OXIDES,VARIOUS HYDROCARBONS,ACRID FUMES.MFR
DIV:(FORMERLY ADVANCED COATINGS & CHEMICALS).
================== Physical/Chemical Properties ==================
Boiling Pt:B.P. Text:181F,83C
Melt/Freeze Pt:M.P/F.P Text:N/K
Decomp Temp:Decomp Text:N/K
Vapor Pres:33 MMHG
Vapor Density:>1 (AIR=1)
Spec Gravity:1.61 (WATER=1)
Evaporation Rate & Reference:SLOWER THAN BUTYL ACETATE
Solubility in Water:NEGLIGIBLE
Appearance and Odor:N/K
Percent Volatiles by Volume:39
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
ALKALINE MATERIALS,STRONG ACIDS,OXIDIZING MATERIALS.
Stability Condition to Avoid:EXCESSIVE HEAT,POOR VENTILATION.CORROSIVE
ATMOSPHERE,EXCESSIVE AGING,SPARKS,OPEN FLAME.
Hazardous Decomposition Products:CARBON MONOXIDE,CARBON DIOXIDE,OXIDES
OF NITROGEN,VARIOUS HYDROCARBONS,ACRID FUMES.
Conditions to Avoid Polymerization:WILL NOT OCCUR.
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSAL MUST BE IN ACCORDANCE WITH
FEDERAL,STATE AND LOCAL REGULATIONS .COLLECT
ABSORBENT/WATER/SPILLED LIQ MIX INTO METAL CONTRS & ADD ENOUGH
WATER TO COVER.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|