MATERIAL SAFETY DATA SHEET
INHALATION:
SECTION 1 - PRODUCT AND COMPANY INFORMATION
Vapor and/or spray mist may be harmful if inhaled. Vapor irritates eyes,
nose, and throat.
Grow Automotive Refinish Products INGESTION:
19699 Progress Drive Harmful if swallowed.
Strongsville, OH 44149 SIGNS & SYMPTOMS OF OVEREXPOSURE:
Grow Automotive Finishes is part of PPG Industries, Inc. Repeated exposure to high vapor concentrations may cause irritation of
the respiratory system and permanent brain and nervous system
EMERGENCY PHONE NUMBERS (412) 434-4515 (U.S.) damage. Eye watering, headaches, nausea, dizziness and loss of
(24 hours/day): coordination are indications that solvent levels are too high. Intentional
(514) 645-1320 (Canada) misuse by deliberately concentrating and inhaling the contents can be
01-800-00-21-400 (Mexico) harmful or fatal. Dryness, itching, cracking, burning, redness, and
0532-3889090 (China) swelling are conditions associated with excessive skin contact.
TECHNICAL (440) 572-2800 (STRONGSVILLE OHIO) 8:00
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Not
INFORMATION: a.m. - 5:00 p.m. EST
applicable.
PRODUCT SAFETY/MSDS INFORMATION: (412) 492-5555 7:00 a.m.
CHRONIC OVEREXPOSURE EFFECTS
- 4:30 p.m. EST
Avoid long-term and repeated contact.
Product ID: ADV-108 (0808)
Repeated exposure to vapors above recommended exposure limits (see
PRODUCT NAME: ENAMEL REDUCER MEDIUM
Section 8) may cause irritation of the respiratory system and permanent
SYNONYMS: None
brain and nervous system damage. Intentional misuse by deliberately
ISSUE DATE: 09/20/2004
concentrating and inhaling the contents can be harmful or fatal. This
EDITION NO.: 2
product contains toluene. Toluene inhalation in animals (greater than
CHEMICAL SOLVENT
1500 ppm) and intentional inhalation of toluene-containing products by
FAMILY:
humans (e.g. glue) has caused adverse fetal development effects.
EMERGENCY OVERVIEW:
The effects of long-term, low level exposures to this product have not
Extremely flammable. Vapors may cause flash fires. Keep away from
been determined. Safe handling of this material on a long-term basis
heat, sparks, flames, and other sources of ignition. Do not smoke.
should emphasize the prevention of all contact with this material to avoid
Extinguish all flames and pilot lights. Turn off stoves, heaters, electrical
any effects from repetitive acute exposures. See Section 11, of this
motors, and other sources of ignition during use and until all vapors/odors
MSDS for a detailed list of chronic health effects information available on
are gone.CAUSES EYE IRRITATION. CAUSES PRIMARY SKIN
individual ingredients in this product.
IRRITATION. MAY BE ABSORBED THROUGH THE SKIN.VAPOR
AND/OR SPRAY MIST MAY BE HARMFUL IF INHALED. VAPOR
IRRITATES EYES, NOSE, AND THROAT.HARMFUL IF SWALLOWED. SECTION 4 - FIRST AID MEASURES
If ingestion, irritation, any type of overexposure or symptoms of
overexposure occur during or persists after use of this product, contact a
POISON CONTROL CENTER, EMERGENCY ROOM OR PHYSICIAN
SECTION 2 - COMPOSITION INFORMATION
immediately; have Material Safety Data Sheet information available.
The following ingredient(s) marked with an "x" are considered
EYE CONTACT:
hazardous under applicable U.S. OSHA and/or Canadian WHMIS
Remove contact lens and pour a gentle stream of warm water through the
regulations. If no ingredients are listed, then there are no U.S. OSHA
affected eye for at least 15 minutes. If irritation persists, contact a poison
and/or Canadian WHMIS hazardous ingredients in this product.
control center, emergency room, or physician as further treatment may be
Material/ Percent Hazardous
necessary.
CAS Number
V.M. AND P. NAPHTHA 40 - 70 X SKIN CONTACT:
8032-32-4 Run a gentle stream of water over the affected area for 15 minutes. A
ACETONE 10 - 30 X mild soap may be used if available. If any symptoms persist, contact a
67-64-1
poison control center, emergency room, or physician as further treatment
TOLUENE 10 - 30 X
may be necessary.
108-88-3
INHALATION:
2-BUTOXYETHYL ACETATE 5 - 10 X
Remove from area to fresh air. If symptomatic, contact a poison control
112-07-2
DIMETHYL GLUTARATE 1-5 X center, emergency room or physician for treatment information.
1119-40-0 INGESTION:
[As Rubber solvent (Naphtha)] * X See Sections 8 Gently wipe or rinse the inside of the mouth with water. Sips of water
8032-32-4 and 15 for
may be given if person is fully conscious. Never give anything by mouth
information.
to an unconscious or convulsing person. Do Not induce vomiting.
Contact a poison control center, emergency room or physician right away
SECTION 3 - HAZARDS IDENTIFICATION as further treatment will be necessary.
ACUTE OVEREXPOSURE EFFECTS
SECTION 5 - FIRE FIGHTING MEASURES
EYE CONTACT:
FLAMMABLE PROPERTIES
Causes eye irritation. Redness, itching, burning sensation and visual
FLASHPOINT: 3 Degrees F ( -16 Degrees C)
disturbances may indicate excessive eye contact.
FLASHPOINT TEST METHOD:
SKIN CONTACT:
Pensky-Martens Closed Cup
Causes primary skin irritation. Dryness, itching, cracking, burning,
UEL: Not Available.
redness, and swelling are conditions associated with excessive skin
LEL: 2.0
contact.
AUTOIGNITION TEMPERATURE:
SKIN ABSORPTION:
Not Available.
May be absorbed through the skin.
__________________________________________________________________
Page 1 of 4
_______________________________________________________________________________________________________________
Grow Automotive Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Grow Automotive Finishes is part of PPG Industries, Inc.
Product ID: ADV-108 (0808)
PRODUCT NAME: ENAMEL REDUCER MEDIUM
EXTINGUISHING MEDIA: RESPIRATOR:
Use National Fire Protection Association (NFPA) Class B extinguishers Overexposure to vapors may be prevented by ensuring proper ventilation
(carbon dioxide, dry chemical, or universal aqueous film forming foam) controls, vapor exhaust or fresh air entry. A NIOSH- approved air
designed to extinguish NFPA Class IB flammable liquid fires. Water spray purifying respirator with the appropriate chemical cartridges or a positive-
may be ineffective. Water spray may be used to cool closed containers pressure, air-supplied respirator may also reduce exposure. Read the
to prevent pressure build-up and possible autoignition or explosion when respirator manufacturer's instructions and literature carefully to determine
exposed to extreme heat. the type of airborne contaminants against which the respirator is effective,
PROTECTION OF FIREFIGHTERS: its limitations, and how it is to be properly fitted and used. Provide general
Fire-fighters should wear self-contained breathing apparatus and full dilution or local exhaust ventilation in volume and pattern to keep the
protective clothing. concentration of ingredients listed in Section 2 below the lowest
UNUSUAL FIRE AND EXPLOSION HAZARDS: suggested exposure limits, the LEL below the stated limit, and to remove
Keep this product away from heat, sparks, flame, and other sources of decomposition products during welding or flame cutting.
ignition (i.e., pilot lights, electric motors, static electricity). Invisible vapors GENERAL HYGIENE - ESTABLISHED EXPOSURE LIMITS
can travel to a source of ignition and flash back. Do not smoke while If Threshold Limit Values (TLVs) have been established by ACGIH,
using this product. Keep containers tightly closed when not in use. Closed OSHA, Ontario or PPG, they will be listed below. These limits are
containers may explode when overheated. Do not apply to hot surfaces. intended for use in the practice of industrial hygiene as guidelines or
Toxic gases may form when this product comes in contact with extreme recommendations in the control of potential workplace health hazards.
heat. May produce hazardous decomposition products when exposed to These limits are not a relative index of toxicity and should not be used by
extreme heat. Extreme heat includes, but is not limited to, flame cutting, anyone without industrial hygiene training.
brazing, and welding.
Material/ Percent ACGIH TLV ACGIH OSHA PEL OSHA
SECTION 6 - ACCIDENTAL RELEASE MEASURE CAS Number STEL STEL
V.M. AND P. 40 - 70 300 ppm Not 300 ppm 400 ppm
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED:
NAPHTHA established
Provide maximum ventilation. Only personnel equipped with proper
8032-32-4
respiratory, skin, and eye protection should be permitted in the area.
ACETONE 10 - 30 500 ppm 750 ppm 750 ppm 1000 ppm
Remove all sources of ignition. Take up spilled material with sand,
67-64-1
vermiculite, or other noncombustible absorbent material and place in TOLUENE 10 - 30 S- 50 ppm Not 100 ppm 150 ppm
clean, empty containers for disposal. Only the spilled material and the 108-88-3 established
absorbant should be placed in this container. [As Rubber solvent * Not Listed Not Listed Not Listed Not Listed
(Naphtha)]
8032-32-4
SECTION 7 - HANDLING AND STORAGE
PRECAUTIONS TO BE TAKEN DURING HANDLING AND STORAGE:
Vapors may collect in low areas. If this material is part of a multiple Key: OSHA=Occupational Safety and Health Administration;
component system, read the Material Safety Data Sheet(s) for the other PEL=Permissable Exposure Limit; Ceiling=PEL Ceiling Limit; STEL=PEL
component or components before blending as the resulting mixture may Short-Term Exposure Limit; Skin=OSHA Skin Designation.
have the hazards of all of its parts. Containers should be grounded when Material/ Percent Ontario Ontario PPG IPEL PPG STEL
pouring. Avoid free fall of liquids in excess of a few inches. CAS Number TWA STEL
500 MG/m3
STORAGE: V.M. AND P. 40 - 70 Not Not Not
NAPHTHA established established established
Do not store above 120 degrees F.(48 degrees C.). Store large quantities
8032-32-4
in buildings designed and protected for storage of NFPA Class IB
ACETONE 10 - 30 500 PPM 750 PPM Not Not
flammable liquids.
67-64-1 established established
TOLUENE 10 - 30 50 PPM Not Not Not
SECTION 8 - EXPOSURE CONTROLS & PERSONAL PROTECTION 108-88-3 established established established
2-BUTOXYETHYL 5 - 10 S- 25 PPM 75 PPM 25 PPM Not
ENGINEERING CONTROLS:
ACETATE established
Provide general dilution or local exhaust ventilation in volume and pattern
112-07-2
to keep the concentration of ingredients listed in Section 8 below the
DIMETHYL 1-5 Not Not 1.5 PPM Not
lowest suggested exposure limits, the LEL below the stated limit, and to GLUTARATE established established established
remove decomposition products during welding or flame cutting. 1119-40-0
[As Rubber solvent * Not Listed Not Listed Not Not
(Naphtha)] established established
PERSONAL PROTECTIVE EQUIPMENT 8032-32-4
EYES:
Wear chemical-type splash goggles when possibility exists for eye
Key: ACGIH=American Conference of Governmental Industrial
contact due to splashing or spraying liquid, airborne particles, or vapors.
Hygienists; OSHA=Occupational Safety and Health Administration;
SKIN/GLOVES:
TLV=Threshold Limit Value; TWA=Time Weighted Average;
Wear protective clothing to prevent skin contact. Apron and gloves
PEL=Permissible Exposure Limit; IPEL=Internal Permissible Exposure
should be constructed of: butyl, neoprene, or nitrile rubber. No specific
Limit; Ceiling=TLV or PEL Ceiling Limit; STEL=TLV or PEL Short-Term
permeation/degradation testing have been done on protective clothing for
Exposure Limit; Skin= Skin Absorption Designation. [C- Ceiling Limit; S-
this product. Recommendations for skin protection are based on
Potential Skin Aborption; R-Respirable Dust]
infrequent contact with this product. For frequent contact or total
Additional Information Not applicable.
immersion, contact a manufacturer of protective clothing for appropriate
chemical impervious equipment. Clean contaminated clothing and shoes.
SECTION 9 - PHYSICAL & CHEMICAL PROPERTIES
(FORMULA VALUES, NOT SALES SPECIFICATIONS)
SPECIFIC GRAVITY: .803
PHYSICAL STATE: Liquid
__________________________________________________________________
Page 2 of 4
_______________________________________________________________________________________________________________
Grow Automotive Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Grow Automotive Finishes is part of PPG Industries, Inc.
Product ID: ADV-108 (0808)
PRODUCT NAME: ENAMEL REDUCER MEDIUM
Percent Solids: .00 SECTION 12 - ECOLOGICAL INFORMATION
Percent Volatile by Volume: 100.000 POTENTIAL ENVIRONMENTAL EFFECTS
pH: Not available. Ecotoxicity: No Information Available.
ODOR THRESHOLD: Not available.
Vapour Pressure: 81.8 mmHg
ENVIRONMENTAL FATE
ODOR/APPEARANCE: Non-viscous liquid with an odor
Mobility: No Information Available.
characteristic of the ingredients
Biodegradation: No Information Available.
listed in Section 2.
Bioaccumulation: No Information Available.
VAPOR DENSITY: HEAVIER THAN AIR
Evaporation Rate: 393
BOILING POINT OR RANGE: 133- 439Degrees F PHYSICAL/CHEMICAL
Freezing Point or Range: Not Applicable.
Hydrolysis: No Information Available.
Melting Point or Range(掳C): Not Applicable.
Photolysis: No Information Available.
Octanol/Water Partition Not Applicable.
Coefficient:
WEIGHT PER GALLON: 6.69 (U.S.) / 8.0 (IMPERIAL) SECTION 13 - DISPOSAL CONSIDERATIONS
Provide maximum ventilation, only personnel equipped with proper
respiratory and skin and eye protection should be permitted in the area.
Take up spilled material with sawdust, vermiculite, or other absorbent
SECTION 10 - STABILITY AND REACTIVITY
material and place in containers for disposal.
STABILITY:
Waste material must be disposed of in accordance with federal, state,
This product is normally stable and will not undergo hazardous reactions.
provincial and local environmental control regulations. Empty containers
CONDITIONS TO AVOID:
should be recycled by an appropriately licensed reconditioner/salvager or
None Known.
disposed of through a permitted waste management facility. Additional
INCOMPATIBLE MATERIALS:
disposal information is contained on the Environmental Data Sheet for
Avoid contact with strong alkalies, strong mineral acids, or strong
this product, which can be obtained from your PPG representative.
oxidizing agents.
HAZARDOUS POLYMERIZATION:
None Known. SECTION 14 - TRANSPORTATION INFORMATION
HAZARDOUS DECOMPOSITION PRODUCTS: Proper Shipping Name: Paint Related Material
- Carbon monoxide - Carbon dioxide NOS Technical Name: None
Hazard Class: 3
Subsidiary Class(es): None
UN Number: UN1263
SECTION 11 - TOXICOLOGICAL INFORMATION Packing Group: II
ACUTE TOXICITY
USA - RQ Hazardous Substances: Toluene, Acetone
Material/ Percent ORAL DERMAL INHALATION
USA-RQ Hazardous Substance Toluene>6188.18 Pounds,
CAS Number LD50 (g/kg) LD50 (g/kg) LC50 (mg/l)
ACETONE 10 - 30 5.80 g/kg 20.00 g/kg Not Available Threshold Ship Weight: Acetone>20325.23 Pounds
67-64-1 Marine Pollutant Name: None
TOLUENE 10 - 30 5.00 g/kg 12.12 g/kg Not Available USA Shipments Only - RQ Threshold Ship Weight: This is the total
108-88-3
weight of this product that must be shipped to exceed the RQ quantity.
2-BUTOXYETHYL 5 - 10 2.40 g/kg 1.50 g/kg Not Available
ACETATE
112-07-2
SECTION 15 - REGULATORY INFORMATION
CHRONIC TOXICITY
INVENTORY STATUS
Target Organs:
U.S. TSCA: This product and/or all of its components are listed on the
- Teratogen - Bone marrow and blood tissues - Blood - Kidney - Liver -
U.S. TSCA Inventory or is otherwise exempt from TSCA Inventory
Brain - Central nervous system - Lung
reporting requirements.
FEDERAL REGULATIONS
Mutagenicity Toxicity: US Regulations
This has not been tested for this product.
Reproductive Toxicity:
This has not been tested for this product.
SUPPLEMENTAL HEALTH INFORMATION:
Material/ Percent
CAS Ingredient Specific Animal Data:
Number
2- 5 - 10 This product contains an ethylene series glycol ether
BUTOXYET and/or acetate which has been shown to cause adverse
HYL effects on the kidneys, liver, blood and/or blood-forming
ACETATE tissue.
112-07-2
__________________________________________________________________
Page 3 of 4
_______________________________________________________________________________________________________________
Grow Automotive Refinish Products
19699 Progress Drive
Strongsville, OH 44149
Grow Automotive Finishes is part of PPG Industries, Inc.
Product ID: ADV-108 (0808)
PRODUCT NAME: ENAMEL REDUCER MEDIUM
Additional environmental information is contained on the Environmental
Material/ Percent
CAS Number CERCLA HS - SARA EHS- SARA 313 Data Sheet for this product, which can be obtained from your PPG
RQ (LBS) TPQ (LBS) representative.
V.M. AND P. 40 - 70 Not Listed Not Listed Not Listed 1409 000002 (00304398.001)(09/20/04)
NAPHTHA
040916, 000, 0808
8032-32-4
ACETONE 10 - 30 5000 lbs Not Listed Not Listed
*** END OF MSDS ***
67-64-1
TOLUENE 10 - 30 1000 lbs Not Listed Listed
108-88-3
2-BUTOXYETHYL 5 - 10 Not Listed Not Listed Not Listed
ACETATE
112-07-2
DIMETHYL 1-5 Not Listed Not Listed Not Listed
GLUTARATE
1119-40-0
SARA 311/312
Health (acute): Yes
Health (chronic): Yes
Fire (flammable): Yes
Pressure: No
Reactivity: No
WHMIS HAZARD CLASS: - Class B, Division 2 - Class D, Division 2,
Subdivision A - Class D, Division 2, Subdivision B
STATE/PROVINCIAL REGULATIONS
CALIFORNIA PROP. 65: WARNING: This product contains a chemical
known to the State of California to cause birth defects or other
reproductive harm.
Additional Information
Key: IARC- International Agency on the Research of Cancer; ACGIH-
American Conference of Governmental Industrial Hygienists; NTP-
National Toxicology Program *Denotes chemical as NTP Known
Carcinogen; + Denotes NTP Possible Carcinogen; OSHA-
Occupational Safety and Health Administration.
SECTION 16 - OTHER INFORMATION
Hazard Rating Systems
NFPA Rating: 2 30
HMIS Rating: 2*30
Rating System: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe,
*=Chronic Effects.
HMIS=Hazardous Materials Identification System; NFPA=National Fire
Protection Association;
Safe handling of this product requires that all of the information on the
MSDS be evaluated for specific work environments and conditions of use.
PREPARED BY: Product Safety Department
REASON FOR REVISION: Section 1 has been updated. Section 2 has
been updated. Changes to this section may also result in changes in
sections 8, 11 and/or 15. Section 5 has been updated. Section 9 has
been updated. Date. Edition.
Updated MSDS
format.
This Material Safety Data Sheet has been prepared in accordance with
Canada's Workplace Hazardous Materials Information System (WHMIS)
and the OSHA Hazard Communication Standard (29 CFR 1910.1200),
the supplier notification requirements of SARA Title III, Section 313 and
other applicable right-to-know regulations.
__________________________________________________________________
Page 4 of 4
|