Finnaren & Haley Paints
Industrial & Marine Coatings
Technical Data Sheet
Indulon 868 HS Epoxy Mastic Non-Skid SKU: 868000
Activator: 868801
Interior / Exterior 0406
Description
(Not Intended For Residential Use) Indulon 868 HS Epoxy Mastic Non-Skid is a two component, polyamide modified, low VOC, high
performance coating for demanding industrial maintenance, marine and architectural applications. It is a tough and durable satin finish perfect for
use on steel, galvanized, aluminum and masonry. It should be used wherever non-skid properties, chemical and abrasion resistance, resistance to
corrosive environments and outstanding adhesion are essential. Indulon 868 HS Epoxy Mastic Non-Skid is great for use on properly prepared
concrete & steel surfaces in refineries, offshore platforms, chemical plants, food & beverage plants and pulp & paper mills.
Technical Data (Mixed)
ta(Mixed)
Type Polyamide Modified Epoxy
1190 ft2 per gallon @ 1 dry mil
Theoretical Coverage
Recommended DFT per Coat 4 - 6 mils DFT
Gloss Satin
Weight per Gallon (Gray 16.7 + 0.5 lbs.) (Red Oxide17.6 + 0.5 lbs.) (Black 16.1 + 0.5 lbs)
Viscosity 95-105 KU
Solids: by Volume (Gray 74.0 + 2%) (Red Oxide 69.1 + 2%) (Black 72.1 + 2%)
by Weight 89 + 2%
VOC < 2.0 lbs per gallon (240 g/l)
Flash Point 59掳F
Color (Federal Standard 595-36076 Gray 868752) (Light Gray 868750)
(Red Oxide 868395) (Black 868700) (Activator 868801)
Packaging 5-Gallon Kits
Surface Preparation
All surfaces must be thoroughly cleaned to remove dirt, grease, mill scale, loose rust, chalk, and any other contaminants that can reduce adhesion
via SSPC-SP1 solvent cleaning.
METAL: Sandblasting is recommended to remove rust and mill scale. Use commercial blast to SSPC-SP6 for mild exposures and near-white blast
SSPC-SP10 for severe exposures. Where blasting is not possible, thorough scraping and wire brushing may be substituted at some possible
sacrifice in performance.
CONCRETE/MASONRY: Cure for at least 30 days before painting. Remove loose or excess mortar, efflorescence, laitance and concrete form
release compounds that reduce adhesion. Etch or abrasive blast slick or glazed concrete before use on floors.
PREVIOUSLY PAINTED SURFACES: Scrape loose, scaly, peeling paint and sand the edges smooth. If the paint is glossy, sand to dull the
surface. Remove any rust and scale from ferrous metal. If mildew is present, remove completely by sterilizing the surface with mildew remover
and detergent. Rinse well and allow to dry before painting.
Primers
CONCRETE/MASONRY should first be coated to fill the voids with Ready Mixed Block Filler (751100) if a smooth finish is desired.
STEEL: Indurazinc HRZ-18 or FB Zinc Inorganic Zinc Rich Primer, 885 Organic Zinc Rich Primer or Indulon 235, 883, 894 Epoxies.
Mixing & Induction
Thoroughly stir each component. Pour the activator, part B (868801), into the pigmented component, part A (868xxx) (mixing ratio by volume: 1
part activator to 5.25 parts pigmented component), mix well and allow the combined mixture to sit for 15 minutes @ 70-90掳F or 30 minutes @ 55-
70掳F before use. Pot life is 3-4 hrs. Do not mix more than can be applied during the product鈥檚 useful pot life.
Finnaren & Haley, Inc.; Corporate Office and Manufacturing
901 Washington St., Conshohocken, PA 19428
1-800-843-9800 or fax to (610)825-1184
Finnaren & Haley Paints
Industrial & Marine Coatings
Technical Data Sheet
Indulon 868 HS Epoxy Mastic Non-Skid SKU: 868000
Activator: 868801
Thinning
Mixed Indulon 868 HS Epoxy Mastic Non-Skid may be thinned with a maximum of 25 fluid ounces per mixed gallon with Finnaren & Haley
791851 Low Temperature Universal Reducer.
Pot Life
Maximum 4 hours @ 77掳F. In order to maintain application properties, mix (activate) only what can be applied in 3-4 hours.Once activated, keep
under agitation to prevent settling of non - skid.
Application
BRUSH, ROLL or SPRAY: Allow the activated paint 15 minutes induction time.
Conventional Spray: Use bottom feed outlet pressure pot with dual regulators.
Gun - DeVilbiss MBC-516, Fluid Tip - 3/8, Air Cap - round or slotted
Atomization Pressure - 30 psi, Fluid Pressure - 25 psi
May also be applied by squeegee or gauge rake
Roller: For limited applications use 3/8" woven with phenolic core
Brush: For limited applications Nylon/Polyester or Natural Bristle
Recommended Spread Rate
Approximately 200 - 300 ft2 per gallon. This may vary depending on the porosity of the surface.
Clean Up
Clean up all tools and equipment promptly with 791851 Reducer.
Dry Time
@ 77掳F and 50% R.H. Expect longer dry times in periods of higher humidity or lower temperatures or when applying thicker films.
To Touch: 2 - 4 hours
Tack Free: 6 - 8 hours
To Recoat: 6 -72 hours
Dry Hard: 24 hours
Special Information
Do not apply if material, substrate or ambient temperature is below 50掳F. Some yellowing may occur in light colors if exposed to temperatures
exceeding 200掳F. Old coatings should be tested for lifting before applying Indulon 868 HS Epoxy Mastic Non-Skid. Exterior exposure causes
color change, gloss loss and chalking, however, this does not effect protective performance properties.
Right to Know & Safety
The label complies with all applicable Right to Know laws. For information on safety hazards associated with this product please refer to MSDS
sheets.
Warranty
This product will perform as claimed if directions are followed. Since we cannot control conditions or methods of use, the warranty is limited to
replacement or refund value of this product actually used. This warranty does not include labor or labor costs.
Finnaren & Haley, Inc.; Corporate Office and Manufacturing
901 Washington St., Conshohocken, PA 19428
1-800-843-9800 or fax to (610)825-1184
|