Page 1 of 10
{Front of Bag}
SENATOR庐 70WP WSB1
GROUP 1 FUNGICIDE
SYSTEMIC FUNGICIDE
AGRICULTURAL
WETTABLE POWDER
GUARANTEE:
thiophanate-methyl 70%
READ THE LABEL BEFORE USING
REGISTRATION NO.: 27297
PEST CONTROL PRODUCTS ACT
ENGAGE Agro Corporation
848 Gordon Street
Guelph, Ontario N1G 1Y7
Net Contents: 1.6 Kg
(8 x 200 g water soluble bags)
Do Not Sell Water Soluble Bags Separately.
Page 2 of 10
{Back Panel of Bag}
GENERAL INFORMATION:
SENATOR 70WP WSB1 Fungicide is a systemic fungicide for control of certain fungus diseases. It is effective against
certain diseases of apples, pears, lowbush blueberries, peaches, nectarines, plums, prunes, cherries, strawberries,
raspberries, white beans, sugarbeets, ornamentals and turf.
NOTICE TO USER:
This control product is to be used only in accordance with the directions on this label. It is an offence under the PEST
CONTROL PRODUCTS ACT to use a control product under unsafe conditions.
NOTICE TO BUYER:
Seller's guarantee shall be limited to the terms set out on the label, and subject thereto, the buyer assumes the risk to
persons or property arising from the use or handling of this product and accepts the product on that condition.
FIRST AID:
If spilled on SKIN, wash off immediately with soap and water. If in EYES, flush with plenty of water. If
SWALLOWED, drink 1 or 2 glasses of water and induce vomiting by inserting finger down the throat. Get medical
attention or contact a Poison Control Centre IMMEDIATELY. Take container, label or product name and Pest Control
Product Registration Number with you when seeking medical attention.
TOXICOLOGICAL INFORMATION:
No specific antidote is available. Treat symptomatically.
PRECAUTIONS:
KEEP OUT OF REACH OF CHILDREN. May be harmful if swallowed or inhaled. Avoid contact with eyes, skin or
clothing. Avoid breathing of dust or spray mist. Wash thoroughly with soap and water after handling. Wash
contaminated clothes before re-use. Do not contaminate food or feed. Do not contaminate domestic or irrigation water
supplies, lakes, streams and ponds.
If this pest control product is to be used on a commodity that may be exported to the U.S. and you require information
on acceptable residue levels in the U.S., visit CropLife Canada鈥檚 website at www.croplife.ca.
HANDLING: The enclosed pouches of Senator 70WP WSB1 Fungicide are water-soluble. Do not allow the pouches
to become wet prior to use. Do not handle the individual pouches with wet hands or wet gloves. Always reseal the
overwrap bag to protect the remaining unused pouches.
DISPOSAL:
1. Triple- or pressure-rinse the empty container. Add the rinsings to the spray mixture in the tank.
2. Follow provincial instructions for any required additional cleaning of the container prior to its disposal.
3. Make the empty container unsuitable for further use.
4. Dispose of the container in accordance with provincial requirements.
5. For information on the disposal of unused, unwanted product, contact the manufacturer or the provincial
regulatory agency. Contact the manufacturer and the provincial regulatory agency in case of a spill, and for
clean-up of spills.
Page 3 of 10
IN CASE OF EMERGENCY INVOLVING A POISONING OR MAJOR SPILL CALL 1-866-336-2983
庐 SENATOR is a registered trademark of ENGAGE Agro Corporation.
Page 4 of 10
{Booklet}
GROUP 1 FUNGICIDE
SENATOR庐 70WP WSB1
SYSTEMIC FUNGICIDE
AGRICULTURAL
WETTABLE POWDER
GUARANTEE:
thiophanate-methyl 70%
READ THE LABEL BEFORE USING
REGISTRATION NO.: 27297
PEST CONTROL PRODUCTS ACT
ENGAGE Agro Corporation
848 Gordon Street
Guelph, Ontario N1G 1Y7
庐 SENATOR is a registered trademark of ENGAGE Agro Corporation.
GENERAL INFORMATION:
SENATOR 70WP WS B1 Fungicide is a systemic fungicide for control of certain fungus diseases. It is effective
against certain diseases of apples, pears, lowbush blueberries, peaches, nectarines, plums, prunes, cherries, strawberries,
raspberries, white beans, sugarbeets, ornamentals and turf.
NOTICE TO USER:
This control product is to be used only in accordance with the directions on this label. It is an offence under the PEST
CONTROL PRODUCTS ACT to use a control product under unsafe conditions.
NOTICE TO BUYER:
Seller's guarantee shall be limited to the terms set out on the label, and subject thereto, the buyer assumes the risk to
persons or property arising from the use or handling of this product and accepts the product on that condition.
FIRST AID:
If spilled on SKIN, wash off immediately with soap and water. If in EYES, flush with plenty of water. If
SWALLOWED, drink 1 or 2 glasses of water and induce vomiting by inserting finger down the throat. Get medical
attention or contact a Poison Control Centre IMMEDIATELY. Take container, label or product name and Pest Control
Product Registration Number with you when seeking medical attention.
Page 5 of 10
TOXICOLOGICAL INFORMATION:
No specific antidote is available. Treat symptomatically.
PRECAUTIONS:
KEEP OUT OF REACH OF CHILDREN. May be harmful if swallowed or inhaled. Avoid contact with eyes, skin or
clothing. Avoid breathing of dust or spray mist. Wash thoroughly with soap and water after handling. Wash
contaminated clothes before re-use. Do not contaminate food or feed. Do not contaminate domestic or irrigation water
supplies, lakes, streams and ponds.
If this pest control product is to be used on a commodity that may be exported to the U.S. and you require information
on acceptable residue levels in the U.S., visit CropLife Canada鈥檚 website at www.croplife.ca.
HANDLING: The enclosed pouches of Senator 70WP WSB1 Fungicide are water-soluble. Do not allow the pouches
to become wet prior to use. Do not handle the individual pouches with wet hands or wet gloves. Always reseal the
overwrap bag to protect the remaining unused pouches.
DISPOSAL:
1. Triple- or pressure-rinse the empty container. Add the rinsings to the spray mixture in the tank.
2. Follow provincial instructions for any required additional cleaning of the container prior to its disposal.
3. Make the empty container unsuitable for further use.
4. Dispose of the container in accordance with provincial requirements.
5. For information on the disposal of unused, unwanted product, contact the manufacturer or the provincial
regulatory agency. Contact the manufacturer and the provincial regulatory agency in case of a spill, and for
clean-up of spills.
IN CASE OF EMERGENCY INVOLVING A POISONING OR MAJOR SPILL CALL 1-866-336-2983
庐 SENATOR is a registered trademark of ENGAGE Agro Corporation.
RESISTANCE MANAGEMENT :
For resistance management, please note that SENATOR 70WP WSB1 Fungicide contains a Group 1 fungicide. Any
fungal population may contain individuals naturally resistant to SENATOR 70WP WSB1 Fungicide and other Group
1 fungicides. A gradual or total loss of pest control may occur over time if these fungicides are used repeatedly in
the same fields. Other resistance mechanisms that are not linked to site of action but specific for individual
chemicals, such as enhanced metabolism, may also exist. Appropriate resistance-management strategies should be
followed.
To delay fungicide resistance:
鈥? Where possible, rotate the use of SENATOR 70WP WSB1 Fungicide or other Group 1 fungicides with
different groups that control the same pathogens.
鈥? Use tank mixtures with fungicides from a different group when such use is permitted.
鈥? Fungicide use should be based on an IPM program that includes scouting, historical information related to
pesticide use and crop rotation and considers cultural, biological and other chemical control practices.
鈥? Monitor treated fungal populations for resistance development.
鈥? If disease continues to progress after treatment with this product, do not increase the use rate. Discontinue
use of this product, and switch to another fungicide with a different target site of action, if available.
鈥? Contact you local extension specialist or certified crop advisor for any additional pesticide resistance-
management and/or IPM recommendations for specific crops and pathogens.
鈥? For further information and to report suspected resistance, contact Engage Agro Corporation at 1-519-826-
7878 or at www.engageagro.com.
Page 6 of 10
Since the occurrence of resistance cannot be foreseen, ENGAGE Agro Corporation accepts no responsibility for any
loss of, or damage to, crops resulting from the failure of SENATOR 70WP WSB1 Fungicide to control the resistant
fungi strains.
MIXING:
Add required amount of SENATOR 70WP WSB1 Fungicide to partially filled tank with mechanical or hydraulic
agitation and then complete filling with water. Maintain full agitation until water soluble bags are completely
dissolved and product is fully dispersed. Add any additional products to the tank after water soluble bags have
completely dissolved. Agitate continuously to keep the material in suspension.
NOTE: Do not mix the soluble bags with liquid fertilizers, substances that contain boron or substances that release
free chlorine. Mixing the water soluble bags with any of these compounds will result in an insoluble substance in
the tank.
RATE:
Rates for orchard spraying are shown as kg of SENATOR 70WP WSB1 Fungicide per 1000 litres water for dilute
spraying based on a volume of approximately 3500 litres per hectare. For concentrate spraying apply the same quantity
per hectare as would be applied by dilute spraying. On turf, use at least 8 litres of water per 100 m2 of area to be
sprayed for dollar spot and use a minimum of 24 litres of water per 100 m2 of area to be sprayed for brown patch,
powdery mildew and pink snow. Use the recommended rate and reduce spray intervals under conditions of severe
disease pressure.
Compatibility:
SENATOR 70WP WSB1 Fungicide is compatible with most pesticides; do not mix with lime or other alkaline
materials.
DIRECTION FOR USE: AERIAL APPLICATION
Apply only by fixed-wing or rotary aircraft equipment that has been functionally and operationally calibrated for the
atmospheric conditions of the area and the application rates and conditions of this label.
Label rates, conditions and precautions are product specific. Read and understand the entire label before opening this
product. Apply only at the rate recommended for aerial applications on this label. Where no rate for aerial application
appears for the specific use, this product cannot be applied by any type of aerial equipment.
Ensure uniform application. To avoid streaked, uneven or overlapped application, use appropriate marking devices.
Use Precautions
Apply only when meteorological conditions at the treatment site allow for complete and even crop coverage. Apply
only under conditions of good practice specific to aerial application as outlined in the Basic Knowledge Requirement
for Pesticide Education in Canada: Applicator Core and Aerial Module, developed by CAPCO.
Do not apply to any body of water. Avoid drifting of spray onto any body of water or other non-target areas. Specified
buffer zones should be observed.
Coarse sprays are less likely to drift, therefore, avoid combinations of pressure and nozzle type that will result in fine
particles (mist). Do not apply during periods of dead calm or when wind velocity and direction pose a risk of spray
drift. Do not spray when the wind is blowing towards a nearby sensitive crop, garden, terrestrial habitat (such as
shelter-belt) or aquatic habitat.
Operator Precautions
Do not allow the pilot to mix chemicals to be loaded onto the aircraft. Loading of premixed chemicals with a closed
system is permitted.
Page 7 of 10
It is desirable that the pilot has communication capabilities at each treatment site at the time of application.
The field crew and the mixer/loaders must wear chemical resistant gloves, coveralls and goggles or face shield during
mixing/loading, cleanup and repair. Follow the more stringent label precautions in cases where the operator
precautions exceed the generic label recommendations on the existing ground boom label.
All personnel on the job site must wash hands and face thoroughly before eating and drinking. Protective clothing,
aircraft cockpit and vehicle cabs must be decontaminated regularly.
Product Specific Precautions
Read and understand the entire label before opening this product. If you have any questions, call the manufacturer at 1-
800-900-5487 or obtain technical advice from the distributor or your provincial agricultural representative. Application
of this specific product must meet and/or conform to the following:
Volume: Apply the recommended rate in a minimum spray volume of 50 litres per hectare.
APPLES AND PEARS:
NOTE: Always use SENATOR 70WP WSB1 Fungicide in a tank mix with a suitable protectant fungicide, such as
Captan, unless otherwise specified.
Apple Scab, Powdery Mildew: Spray with ground application equipment using sufficient volume for thorough
coverage. DO NOT APPLY BY AIR.
Eastern Canada
Tank Mix with Captan: Apply at the rate of 175 grams SENATOR 70WP WSB1 Fungicide plus 1 kg of Captan 50W
(625 g Captan 80W) per 1000 litres of water. The rate per hectare is 625 grams of SENATOR 70WP WSB1 Fungicide
+ 3.25 kg of Captan 50W (or 2 kg of Captan 80W) in a full-season spray program.
Do not apply tank mix with Captan within 7 days of harvest. Do not use Captan with or shortly after oil sprays, or
solvent formulations of parathion.
British Columbia:
For apple scab and powdery mildew control in the Okanagan-Kootenay region of British Columbia, apply SENATOR
70WP WSB1 Fungicide at the rate of 2.25 kg per hectare. Consult local authorities for timing of applications. May be
applied up to the day before harvest.
LOWBUSH BLUEBERRIES:
Blossom and Twig Blight: Apply 1.1 kg of SENATOR 70WP WSB1 Fungicide in 1000 litres of water per hectare
when using ground application equipment or 50-60 litres of water for aerial applications. Commence applications at
bud break. Make 3-4 applications at 10 - 14-day intervals. Exact interval used depends on weather conditions and
disease development. Contact local extension officials. Do not apply within 60 days of harvest.
PEACHES, NECTARINES, PLUMS, PRUNES, CHERRIES:
Brown Rot: Apply 500 grams of SENATOR 70WP WSB1 Fungicide per 1000 litres of water (1.75 kg per hectare),
using ground application equipment, at very early stages of blossoming, and at full bloom to ensure adequate
protection. In British Columbia apply at pink and full bloom stage. Repeat 3 to 5 days later if wet weather conditions
prevail. May be applied up to the day before harvest. DO NOT APPLY BY AIR.
Page 8 of 10
Experience has shown that alternating contact fungicides and SENATOR 70WP WSB1 Fungicide for control of brown
rot will provide best results with least expectancy of resistance developing to the fungicides.
RASPBERRIES:
Powdery Mildew, Fruit Rots: Apply 500 grams of SENATOR 70WP WSB1 Fungicide per 1000 litres of water (1.1
kg per hectare), using ground application equipment, during flowering and repeat every 7 - 10 days as necessary. May
be applied up to the day before harvest. DO NOT APPLY BY AIR.
STRAWBERRIES:
Fruit Rot (Botrytis), Leaf Spot: Apply 500 grams of SENATOR 70WP WSB1 Fungicide per 1000 litres of water (1.1
kg per hectare), using ground application equipment, commencing when buds are visible in the crown. Repeat every 7
- 10 days as required up to the day before harvest. During rainy periods which favour rapid development of fruit rots,
reduce spray interval to 3 - 5 days. May be applied up to the day before harvest. DO NOT APPLY BY AIR.
WHITE BEANS:
White Mold on White Beans: Apply SENATOR 70WP WSB1 Fungicide at 1.75 - 2.25 kg per hectare in 1000 litres
of water per hectare when using ground application equipment or 50-60 litres of water for aerial applications when
conditions favouring development of disease exist (e.g., warm, humid weather combined with heavy, dense crop
foliage). This usually occurs during the early stages of bloom prior to the rows closing in. Spray to achieve optimum
coverage and penetration on all parts of the plant. If disease conditions persist, repeat applications may be warranted.
NOTE: Do not feed or allow livestock to graze on treated crops.
SUGARBEETS:
Leaf Spot (Cercospora sp.) of Sugarbeets: Apply SENATOR 70WP WSB1 Fungicide at 0.42 鈥? 0.56 kg of product
per hectare, using ground application equipment, when disease first appears. Repeat 14 鈥? 21 days later if required.
Make a maximum of two applications per growing season. DO NOT APPLY BY AIR.
DO NOT APPLY WITHIN 21 DAYS OF HARVEST.
FOR SUGARBEETS GROWN FOR EXPORT ONLY.
NO SUGARBEETS OR PARTS OF SUGARBEETS ARE TO BE USED AS FODDER OR FEED IN
CANADA.
TO DELAY THE SELECTION OF RESISTANT STRAINS OF FUNGI, SENATOR SHOULD ALWAYS
BE ALTERNATED WITH A FUNGICIDE OF DIFFERENT CHEMISTRY
TURF:
SENATOR 70WP WSB1 Fungicide can be applied to golf course greens, tees, fairways and other turf areas. For use on
all fine turf applications of cool and warm season grasses (such as Bentgrass, Blue grass, Fescues, Rye Grass) or their
mixtures. SENATOR 70WP WSB1 Fungicide is not phytotoxic to any of the above-mentioned grasses when used in
accordance with the label. Apply after mowing or avoid mowing for twelve hours after application. Begin
applications, using ground application equipment, when diseases first appear. When disease pressure is severe, apply at
the higher recommended rate. DO NOT APPLY BY AIR.
Rate / 100 m2
Disease Spray Volume Spray Schedule
(per 100 m2)
Dollar Spot (Sclerotinia homoeocarpa) 25-30 g Minimum 8 L Repeat every 10-14 days as required
Brown Patch (Rhizoctonia solani) 30-60 g Minimum 24 L Repeat every 5-7 days as required
Powdery Mildew (Erysiphe graminis) 125-250 g Minimum 24 L* Repeat every 14-21 days as required
Pink Snow Mould (Fusarium nivale) 125-175g Minimum 24 L Repeat when required
* For Powdery mildew only, wash SENATOR 70WP WSB1 Fungicide into root zone with 2.5 cm of water
immediately after application
Page 9 of 10
ROSES, ORNAMENTAL PLANTS:
Black Spot of Roses and Powdery Mildew: Apply SENATOR 70WP WSB1 Fungicide at 500-750 g product per
1000 litres of water, using ground application equipment. Repeat every 10-14 days as required. DO NOT APPLY BY
AIR.
GREENHOUSE POTTED ORNAMENTALS:
Powdery Mildew, Botrytis and Leaf Spots: Apply SENATOR 70WP WSB1 Fungicide at 650-850 g per 1000 L of
water, using ground application equipment. Water soil thoroughly with spray solution. Repeat every 7 days as
required.
Stem, Crown and Root Rots caused by Fusarium and Rhizoctonia: Apply Senator 70WP WSB1 Fungicide at 650-
850 g per 1000 L of water as a drench or directed spray by ground application to thoroughly soak the growing media
through the root zone. Repeat after 15 days if required. Note: Senator does not control Pythium or Phytophthora.
ASPEN AND POPLAR:
Marssonina Leaf Spot, Septoria Leaf Spot: Apply SENATOR 70WP WSB1 Fungicide at 1.1 kg product per 1000
litres of water per hectare, using ground application equipment. Repeat every 10 days beginning mid-June. Make a
maximum number of 3 applications per season. DO NOT APPLY BY AIR.
庐 SENATOR is a registered trademark of ENGAGE Agro Corporation.
Page 10 of 10
{Water Soluble Bag Label}
KEEP OUT OF REACH OF CHILDREN
SEE DIRECTIONS FOR USE ON PRODUCT LABEL
FOR COMPLETE PRECAUTIONARY STATEMENTS
GUARANTEE:
THIOPHANATE MEHTYL 70%
WETTABLE POWDER
NET CONTENTS: 50g 鈥? 1 kg
Do not sell water soluble bags separately
|