Quality Control &
Project Literature
Quality control Checklist
Coating application checklist
Daily coating guide
Surface analysis
Environmental conditions
Surface Preparation checklist
Surface profile record
Spark test record
Dry film thickness record
Material batch record
Job timeline
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
QUALITY CONTROL CHECKLIST
Project:
Client:
Area / Item:
REJECT NOTE
ACCEPT
Environment
Surface Profile
Surface Cleanliness
Surface Temperature
Base Coat
Intermediate Coat
Top Coat
Total Film Thickness
Spark Test
QC Inspector:
Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
QC Checklist For Coating Application
Project:
Client:
Area / Item:
N/A
YES NO AMBOENT CONDITIONS
Is the air temperature between F and F?
Is the surface temperature between F and F?
Is the relative humidity below %?
Is the dew point at least 5 F below the surface temperature?
If required, is the environment control equipment in place and operational?
COATING MATERIAL
Primer Intermediate
Finish Touch Up
Batch #
Application Equipment
Is the compressed air supply free of oil and moisture?
Is the surface free of oil, grease, moisture and contamination?
Has the surface remained acceptable per SSPC-SP- ?
Is the surface free of dust, dirt and spent abrasives?
Are the required protective coverings in place?
Is the mixing and application equipment clean and operational?
Are wet film thickness guages being used by the applicator?
Has the material been mixed per the manufactor鈥檚 instructions?
Has the material been spplied with the usable pot life?
QC Inspector: Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR庐 Daily coating Inspection Report
ARCOR
Day
Purchase Order # Report
Job:
Shift
Contracter Sheet
To:
Inspector
Forman Date
Surf
Dry Rel Dew
Operations Permited / Comments
Wet
Location
Time Meth
Temp
Bulb Hum Point
Bulb
Surface Preparation Coating Thickness
Coating Material
OK / Follow
Specific Actual
No. Cleanliness Profile
Item Operation Material Batch
Method
Location
Method
Spec
App
Spec Numbers Range
Avg.
Actual
Spec Meth
Reading
Instrument
Key
Commentary Distribution: Serial No.
Sling Psychrometer
PS
Psychron
PN
Surface Temp. Therm
ST
Tooke Gauge
TG
K-t Comparator (S;SH;GS)
C
Wet Film Gauge
W
Mikrotest
M
Inspector Gauge
I
AS-Airless Spray
B-Brush T-Trowel
R-Roller CS-Conventional Spray
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
Surface Contamination Analysis (KTA)
Project:
Client:
Area / Item:
Calculation Determination 1 Determination 2
Line (1) Tritrator Strip Reading
(ppm) (ppm)
Line (2) Volume of water
Milliliters (ml) Milliliters (ml)
Line (3) = Line (1) x Line (2)
(cm2 = 6.45 x in2)
Micrograms ( ug CI-) Micrograms ( ug CI-)
Line (4) Surface Area Swabbed
(cm2) (cm2)
Line (5)= Line (3) / Line (4)
ug (CI-) per cm2 ug (CI-) per cm2
Line (6) = Line (5) x 10
ug (CI-) per M2 ug (CI-) per M2
QC Inspector:
Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
Environmental Conditions Log
Project:
Client:
Area / Item:
Dry %
Wet Surf.
Comp. Dew
Date Time Bulb R.H.
Bulb Temp
Air Point
QC Inspector: Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
QC Checklist For Surface Preparation
Project:
Client:
Area / Item:
YES NO N/A PRELIMINARY CONDITIONS
Is the compressed air supply free of oil and moisture?
Is the surface free of greese, oil, tar and crayon marks?
List the type(s) of contamination:
Is the surface dry and moisture free?
Are steel defects present?
List the types of defects:
SOLVENT CLEANING
Is solvent cleaning required?
Are clean regs, clean brushes and proper solvent available?
Was solvent cleaning completed as required per SSPC-SP-1?
AMBIENT CONDITIONS
Is the air temperature between F and F?
Is the surface temperature between F and F?
Is the relative humidity below %?
Is the dew point at least 5 F below the surface temperature?
If required, is the enbvironmental control equipment in place and operational?
ISPECTION RESULTS
Was the surface preparation operation completed during the shift?
Did the level of cleanliness meet SSPC-SP- ?
Are two surface profile readings above mils (.001 in)?
Has the surface quality been accepted by thye owners QC Department?
QC Inspector: Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
Surface Profile Record
Project:
Client:
Area / Item:
Area # Area #
Profile Reading Profile Reading
Area #
Area # Profile Reading
Profile Reading
QC Inspector: Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
High Voltage Spark Testing Record
Project:
Client:
Area / Item:
Repair
Defect Location
Serial #
Date:
Retest:
Date:
Retest:
Date:
Retest:
Date:
Retest:
Date:
Retest:
Date:
Retest:
Date:
Retest:
Date:
Retest:
Date:
Retest:
Spark Tester Serial # QC Inspector
Voltage Setting
Inspection Date
Wind Type
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
Dry Film Thickness reading
Project:
Client:
Area / Item:
Location
Location
%/
%/ Thickness
Thickness T Avg.
T Avg.
min
min mils (0.001鈥?)
mils (0.001鈥?)
Sum of Averages
Sum of Averages
Average of Five Readings
Average of Five Readings
Location Location
%/ %/
Thickness Thickness
T T
Avg. Avg.
min min
mils (0.001鈥?) mils (0.001鈥?)
Sum of Averages Sum of Averages
Average of Five Readings Average of Five Readings
QC Inspector: Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR 庐 International
庐
EPOXY TECHNOLOGIES
QUALITY CONTROL INSPECTION REPORT
JOB # PAGE OF
Material Batch Number Record
Project:
Client:
Area / Item:
Date Time Unit Base Activ.
Serial # Product Applied Applied Size Lot # Lot#
QC Inspector: Date Of Inspection:
PO Box 273 South Dennis, MA 02660 Tel: 800-878-9593 Fax: 800-878-9593 Internet: www.ArcorEpoxy.com
ARCOR庐 : Job Time Line
ARCOR庐
Job:
Month:
ACTIVITY
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Full Day Half Day
KEY:
|