MATERIAL SAFETY DATA SHEET



SECTION I                                       PRODUCT INFORMATION



PRODUCT NAME: Form Oil 713                       WHMIS: Not a Controlled Product



PRODUCT DESCRIPTION: A lubricating oil, a mixture of paraffinic and napthenic hydrocarbons, trace amounts of

              aromatic hydrocarbons and additives.



SUPPLIER:            Commercial Oil Company              Phone (905) 560-3244

                     35 Burford Road                     Fax (905) 560-2961

                     Hamilton, Ontario

                     L8E 3C6

SECTION II                                      REGULATED COMPONENTS

The following components are defined in accordance with sub-paragraph 13(a) (i) to (iv) or paragraph 14(a) of the

Hazardous Products Act

                                 No regulated components

SECTION III                                     PHYSICAL DATA

Physical State: Liquid                                  Evaporation Rate: <1 (1=n-butylacetate)

Viscosity: 6.0-7.07 cSt at 40C                          Pour Point: -30 C

Density, kg/m3: 866 @ 15 C                              Appearance: Clear, pale amber liquid (ASTM) <2.5

SECTION IV                                      HEALTH HAZARD INFORMATION

Nature of Hazard

INHALATION: Negligible hazard at normal temperatures (up to 38 deg C). Elevated temperatures or mechanical action

may form vapours, mists or fumes, which may be irritating to the eyes, nose, throat and lungs. Avoid breathing vapours or

mists.

EYE CONTACT: Slightly irritating but will not injure eye tissue.

SKIN CONTACT: Low Toxicity.

                    Frequent or prolonged contact may irritate the skin and cause a skin rash (dermatitis).

INGESTION:          Low Toxicity



OCCUPATIONAL EXPOSURE LIMITS: For oil mists, 5 mg/m3 recommended based on the ACGIH TLV



            HAZARD RATING                                 HAZARD RATING SCALE

               Health     0                               0= Minimal  3= Serious

               Fire      0                                1= Slight   4= Severe

               Reactivity 0                               2= Minimal



SECTION V                                        FIRST AID MEASURES

INHALATION: Vapour pressure of this material is low and as such inhalation under normal conditions is usually not a

problem. If over exposed to oil mist, remove from further exposure. Administer artificial respiration if breathing has

stopped. Keep at rest. Call for prompt medical attention.

EYE CONTACT: Flush eyes with large amounts of water until irritation subsides. If irritation persists, get medical

attention.

SKIN CONTACT: Flush with large amounts of water. Use soap if it is available. Remove severely contaminated

clothing (including shoes) and launder before reuse. If irritation persists, seek medical attention.

INGESTION: If swallowed, DO NOT induce vomiting. Keep at rest. Get prompt medical attention.





SECTION VI                                      PREVENTATIVE AND CORRECTIVE MEASURES

                                                                     2



PERSONAL PROTECTION: The selection of personal protective equipment varies depending upon conditions of use.

Where prolonged and/or repeated skin and eye contact is likely to occur, wear safety glasses with side shields, long

sleeves, and chemical resistant gloves. Where eye contact is unlikely, but may occur as a result of short and/or periodic

exposures, wear safety glasses with side shields. Where concentrations in air may exceed the occupational exposure

limits given in Section 4 and where engineering work practices or other means of exposure reduction are not adequate,

approved respirators may be necessary to prevent overexposure by inhalation.



ENGINEERING CONTROLS: The use of local exhaust ventilation is recommended to control emissions near the

source. Labratory samples should be handled in a fume hood. Provide mechanical ventilation in a confined space.



HANDLING STORAGE AND SHIPPING: Keep containers closed. Handle and open containers with care. Store in a

cool, well-ventilated place away from incompatible materials. Do not handle or store near an open flame, sources of heat,

or sources of ignition.



LAND SPILL: Eliminate source of ignition. Keep public away. Prevent additional discharge of material; if possible do

so without hazard. Prevent spills from entering sewers watercourses or low areas. Contain spilled liquid with sand or

earth. Recover by pumping or using a suitable absorbant. Consult an expert on disposal of recovered material. Ensure

disposal in compliance with government requirements and ensure conformity to local disposal regulations. Notify the

appropriate authorities immediately. Take all additional action necessary to prevent and remedy the adverse affects of the

spill.



WATER SPILL: Remove from surface by skimming or with suitable absorbents. If allowed by local authorities and

environmental agencies, sinking and/or suitable dispersants may be used in unconfined waters. Consult an expert on

disposal of recovered material. Ensure disposal in compliance with government requirements and ensure conformity to

local disposal regulations. Notify the appropriate authorities immediately. Take all action necessary to prevent and

remedy the adverse affects of the spill.

SECTION VII                                       FIRE AND EXPLOSION HAZARD

Flashpoint and method: 164 deg C COC D92

Autoignition: NA          Flammable Limits: LEL NA UEL: NA

GENERAL HAZARDS: Low hazard; liquids may burn upon heating to temperatures at or above the flash point.

Decomposes; flammable/toxic gases will form at elevated temperatures (thermal decomposition). Toxic gases will form

upon combustion.

Empty product containers may contain product residue. Do not pressurize, cut, heat, weld, or expose containers to flame

or other sources of ignition.

FIRE FIGHTING: Use water spray to cool fire-exposed surfaces and to protect personnel. Shut off fuel to fire. Use

foam, dry chemical or water spray to extinguish fire. Respiratory and eye protection required for fire fighting personnel.

Avoid spraying water directly into storage containers due to danger of boilover.

A self-contained breathing apparatus (SCBA) should be used for all indoor fires and any significant outdoor fires. For

small outdoor fires, which may easily be extinguished with a portable fire extinguisher, use of an SCBA may not be

required.

HAZARDOUS COMBUSTIBLE PRODUCTS: Smoke, carbon monoxide and dioxide and traces of oxides of sulphur.

SECTION VIII                                              REACTIVITY DATA

STABILITY: This product is stable. Hazardous polymerization will not occur.

INCOMPATIBLE MATERIALS AND CONDITIONS TO AVOID: Strong oxidizing agents.

HAZARDOUS DECOMPOSITION: Fumes, smoke, carbon monoxide, sulphur oxides if incomplete combustion.

SECTION IX                                                PREPARATION

COMMERCIAL OIL COMPANY                                    Date: March. 31, 2008

Hamilton, Ontario                                         Prepared by: Operations

_________________________________________________________________________________________________

The information presented herein has been compiled from sources considered to be dependable and is accurate to the best of Commercial Oil

Company’s knowledge; however, the Commercial Oil Company makes no warranty whatsoever, expressed or implied, and expressly disclaims all

liability for reliance thereon. Such data are offered solely for your consideration, investigation and verification.