#290
MATERIAL SAFETY DATA SHEET
NFPA RATING: Health = 0, Flammability = 0, Reactivity = 0
HMIS RATING: Health = 0, Flammability = 0, Reactivity = 0
SECTION I -- IDENTITY AND MANUFACTURER'S INFORMATION (0624A)
Manufacturer's Name: HILLYARD INDUSTRIES Product Name: PROTECTIVE COATING
Address: 302 North Fourth Street Date Prepared: May 10, 1994
St. Joseph, MO 64502 Prepared by: Regulatory Affairs Department
Emergency Telephone No.: (800)-424-9300 (Only in the event of chemical emergency involving a spill, leak, fire, exposure or
accident involving chemicals.) Other information calls: (816)233-1321(Ext. 2303)
http://www.hillyard.com
SECTION II -- INGREDIENTS/IDENTITY INFORMATION
Components
(Specific Chemical Identity: Common CAS# OSHA PEL ACGIH OTHER LIMITS %
Name(s) TLV RECOMMENDED
5 mg/M3 5 mg/M3
Zinc oxide (1) 1314-13-2 N.A. less than
0.1
Water 7732-18-5 none none N.A. ---
Acrylate Copolymer 63744-68-3 not established not established N.A. ---
Diethylene glycol monomethyl ether(2) ** 111-77-3 not established not established N.A. 3-5
Alkenes, Polymd. emulsion 68527-08-2 not established not established N.A. ---
Tributoxyethyl Phosphate ** 78-51-3 not established not established N.A. 0.5 -1.5
(1) Regulated by OSHA and the following states: FL., IL., LA., MA., NJ.
(2) Regulated by the following states: FL., PA., RI.
** This product contains the following chemical subject to reporting requirements of SARA Title III, Section 313: Diethylene glycol
monomethyl ether and Tributoxyethyl Phosphate
SECTION III -- PHYSICAL / CHEMICAL CHARACTERISTICS
Boiling Point: 205oF Specific Gravity (H2O = 1): 25oC = 1.02 & 39oC = 1.02
Vapor Pressure (mm Hg.): 18.0 Percent Volatile by Volume (%): 83.7%
Vapor Density (AIR = 1): 1.0 Evaporation Rate (ethyl ether = 1): slower than 1
Solubility in Water: appreciable Appearance and Odor: Creamy, white emulsion;
non-objectionable odor.
SECTION IV -- FIRE AND EXPLOSION HAZARD DATA
Flash point: None (T.C.C.) Flammable Limits: LEL = N.A. UEL = N.A.
Extinguishing Media: Foam, Carbon Dioxide, Dry Chemical, Water Fog.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus (pressure-demand MSHA/NIOSH
approved or equivalent) and full protective gear.
Unusual Fire and Explosion Hazards: Material may spatter if temperatures exceed boiling point.
Polymer film can burn.
SECTION V -- PHYSICAL HAZARDS
Stability: Stable Conditions to Avoid: N/A
Incompatibility (Materials to Avoid): None known to Hillyard
Hazardous Decomposition Products or Byproducts: None known to Hillyard
Hazardous Polymerization: Will not Occur Conditions to Avoid: N/A
SECTION VI -- HEALTH HAZARD DATA
Routes of entry: Inhalation? N/A Skin? N/A Ingestion? N/A
HEALTH HAZARDS (1. Acute and 2. Chronic)
1. None known. (According to Primary Skin Irritation Test [FHSA], product is not an irritant; Eye Irritation Test
[FHSA], not an irritant.) 2. None known to Hillyard Industries
page 2 of #290 PROTECTIVE COATING
HEALTH HAZARD DATA (CONTINUED):
Chemical listed as Carcinogen or Potential Carcinogen:
National Toxicology Program = No I.A.R.C. Monographs = No OSHA = No
This product has no carcinogens listed by IARC, NTP, NIOSH, OR ACGIH as of this date, greater than or equal to 0.1%.
Signs and Symptoms of Exposure:
None known to Hillyard.
Medical Conditions Generally Aggravated by Exposure:
None known to Hillyard
Emergency and First Aid Procedures:
If splashed into eyes flush with water for 15 minutes. Flush skin with water. Ingestion: Drink large quantity of water; induce
vomiting; call physician.
SECTION VII -- PRECAUTIONS FOR SAFE HANDLING AND USE
Steps To Be Taken In Case Material Is Released Or Spilled: Pick up with mop or wet vac and wash away with water.
Waste Disposal Method: Wash small quantities down sewer with large amount of water. Keep spills and cleaning runoffs out of
municipal sewers and open bodies of water. Large spills should be picked up with wet vac or absorbent material. Landfill or
incinerate solids. Dispose of liquid per local, state and federal regulations.
Precautions To Be Taken In Handling And Storing: Freezing of product may rupture container. Product shelf life is best retained
by storage at 45 - 100掳F temperature.
Other Precautions: Inhalation exposure to spray mist should be maintained at less than 10 mg/M3 per eight hours
exposure (TWA limit estimated for nuisance dust).
SECTION VIII -- CONTROL MEASURES:
Respiratory Protection (Specify Type): None required if good ventilation is maintained.
Ventilation:
Local Exhaust = Not required Mechanical (General) = Suggested Special = N.A. Other = N.A.
Protective Gloves: None required Eye Protection: None required
Other Protective Clothing or Equipment: None required.
Work / Hygienic Practices: Do not take internally; wash contaminated clothing and equipment before reuse.
SECTION IX - TRANSPORTATION INFORMATION:
Applicable regulations: no 49 CFR; no IMCO; no IATA.
Proper shipping name: Liquid Floor Wax & Polish
UN No.: not applicable Limited Qty.: not applicable Hazard Class: not applicable
Labels required: not required DOT Exception: not applicable
EPA Hazardous waste number / code: not listed
Hazardous waste characteristics:
Ignitability = not applicable; Corrosivity = not applicable; Reactivity = not applicable.
DISCLAIMER OF WARRANTIES
NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OF ANY NATURE ARE MADE WITH RESPECT TO THE PRODUCT(S) OR INFORMATION CONTAINED IN THIS MATERIAL
SAFETY DATA SHEET.
The information and recommendations contained in this Material Safety Data Sheet are supplied pursuant to 29 CFR 1910.1200 of the Occupational
Safety and Health Standards Hazard Communication Rule. All information contained herein is presented in good faith and is believed to be appropriate
and accurate.
THE BUYER OR USER ASSUMES ALL RISKS ASSOCIATED WITH THE USE, MISUSE OR DISPOSAL OF THIS PRODUCT. THE BUYER OR
USER IS RESPONSIBLE TO COMPLY WITH ALL FEDERAL, STATE OR LOCAL REGULATIONS CONCERNING THE USE, MISUSE OR
DISPOSAL OF THESE PRODUCTS.
|