Search   
MSDS 
:
 Cinnamoyl chloride 98%, Predominantly Trans
CAS 
:
 102-92-1
SYNONYMS 
:
 3-Phenyl-2-propenoyl chloride
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 102-92-1 |Cinnamoyl chloride | 98 | 203-065-5 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Causes burns.Moisture sensitive.

Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns.
Inhalation:
May cause severe irritation of the respiratory tract with sore
throat, coughing, shortness of breath and delayed lung edema. Causes
chemical burns to the respiratory tract.
Chronic:
None

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Flush skin with plenty of water for at
least 15 minutes while removing contaminated clothing and shoes.
Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Do NOT induce vomiting. If conscious and alert,
rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Do NOT use mouth-to-mouth
resuscitation.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Vapors may
be heavier than air. They can spread along the ground and collect
in low or confined areas.
Extinguishing Media:
Do NOT use water directly on fire. Use foam, dry chemical, or carbon
dioxide.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Sweep up, then place into a suitable container for
disposal. Avoid generating dusty conditions. Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Keep container tightly closed. Do not get on skin or in eyes. Do not
ingest or inhale. Use with adequate ventilation. Discard contaminated
shoes.
Storage:
Keep container closed when not in use. Store in a cool, dry,
well-ventilated area away from incompatible substances. Corrosives
area. Keep refrigerated. (Store below 4C/39F.) Store protected
from moisture.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local exhaust ventilation to keep airborne concentrations below the
permissible exposure limits.
Exposure Limits
CAS# 102-92-1:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to minimize
contact with skin.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Crystalline powder
Color: yellow
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 256 - 258 deg C @ 760.00mm Hg
Freezing/Melting Point: 35 - 37 deg C
Autoignition Temperature: Not available.
Flash Point: > 110 deg C (> 230.00 deg F)
Explosion Limits, lower: N/A
Explosion Limits, upper: N/A
Decomposition Temperature:
Solubility in water: very soluble in ligroin
Specific Gravity/Density: 1.16
Molecular Formula: C9H7ClO
Molecular Weight: 166.61

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, dust generation, moisture, excess heat,
oxidizers.
Incompatibilities with Other Materials:
Not available.
Hazardous Decomposition Products:
Hydrogen chloride, phosgene, carbon monoxide, carbon dioxide.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 102-92-1 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Cinnamoyl chloride -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: CORROSIVE SOLID, N.O.S.*
Hazard Class: 8
UN Number: 1759
Packing Group: II
IMO
Shipping Name: CORROSIVE SOLID, N.O.S.
Hazard Class: 8
UN Number: 1759
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE SOLID, N.O.S.
Hazard Class: 8
UN Number: 1759
Packing group: II

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 34 Causes burns.
Safety Phrases:
S 25 Avoid contact with eyes.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 102-92-1: No information available.
Canada
CAS# 102-92-1 is listed on Canada's DSL List.
CAS# 102-92-1 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 102-92-1 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 7/07/1998 Revision #3 Date: 10/10/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Phenethyl alcohol, 99+% 60-12-8
1,8-Diaminonaphthalene, 99% 479-27-6
4,4'-Methylene-Bis-(2,6-Diethylaniline) 99+% 13680-35-8
Poly(styrene), average m.w. 250.000 9003-53-6
Poly(styrene), ultra high molecular weight 9003-53-6
Heptafluorobutyric Acid, 99% 375-22-4
3-Chloro-1,2-Propanediol, 98% 96-24-2
1,2-Dibromobenzene, 99% 583-53-9
2-Amino-2-Methyl-1,3-Propanediol, 99% 115-69-5
Aflatoxin G2, crystalline 7241-98-7
2-Imidazolidone hemihydrate, 99+% 120-93-4
4-Chloro-1-butanol, 90-95% (GC), balance THF and HCl 109-99-9
Dibromomethane, 99% 74-95-3
N,N,3,5-Tetramethylaniline, 99% (GC) 4913-13-7
7-Bromoheptanonitrile, 98% 20965-27-9
o-Phthaloyl dichloride, remainder mainly phthalic acid, 90% 88-95-9
Vanadium(V) oxide, 99.6+% 1314-62-1
2,6-Bis(Hydroxymethyl)-P-Cresol, 97% 91-04-3
Anthrone, 98% 90-44-8
4-tert-Butyltoluene, p.a. 98-51-1
Methyl 4-Nitrobenzenesulfonate, 99+% 6214-20-6
7-Amino-4-Methylcoumarin, 98% 26093-31-2
Ammonium Sulfamate P.A. 7773-06-0
Trans-Stilbene, 96% 103-30-0
tert-Butyl chloroacetate, 99% 107-59-5
Cinnamoyl chloride 98%, Predominantly Trans 102-92-1
Iodine Monochloride, 98% 7790-99-0
Allyl phenyl ether, 99% 1746-13-0
N,N-Diethylethanolamine 100-37-8
Lithium perchlorate 7791-03-9
(S)-(-)-Amino-2-(1'-methoxy-1'-methylethyl )pyrrolidine 118535-61-8
Dl-2,4-pentanediol, 97% 625-69-4
Sodium hexafluoroantimonate, tech. 16925-25-0
1,3-Diphenylguanidine, 97% 102-06-7
4-Butoxyaniline, 97% (gc) 4344-55-2
L(-)-Epinephrine, 99% 51-43-4
Lithium bis(trimethylsilyl)amide 1M solution in THF/cyclohexane 109-99-9
2-Chloro-5-Nitrobenzaldehyde, 97% 6361-21-3
Tetraethylammonium Perchlorate, 95% (Titr.) 2567-83-1
l-Tartaric acid, disodium salt dihydrate, p.a. 6106-24-7
Digoxin, 95% HPLC (on Dried Substance) 20830-75-5
n-Acetylneuraminic acid, from bovine milk, 98% 131-48-6
1,4-Naphthoquinone, 99% (GC), contains up to 6% moisture 130-15-4
Methyl disulfide, 99% 624-92-0
Dowex 1x8-100 ion-exchange resin 12627-85-9
Dowex 1x8-400 ion-exchange resin 12627-85-9
Ethyl red 76058-33-8
Glycylglycine, 99+% 556-50-3
Lithium aluminum hydride, 95+% 16853-85-3
Cerium(IV) Oxide, 99.999%, - 325 Mesh 1306-38-3

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net