**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 1438-91-1 |Furfuryl methyl sulfide | 97.0 | 215-874-0 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37/38
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Irritating to eyes, respiratory system and skin.Stench.The
toxicological properties of this material have not been fully
investigated.
Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation.
Ingestion:
May cause irritation of the digestive tract. The toxicological
properties of this substance have not been fully investigated.
Inhalation:
Causes respiratory tract irritation. The toxicological properties of
this substance have not been fully investigated.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and
drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Antidote:
None reported.
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Use water
spray to keep fire-exposed containers cool. Combustible liquid.
Vapors may be heavier than air. They can spread along the ground and
collect in low or confined areas. Containers may explode when heated.
Extinguishing Media:
In case of fire, use water, dry chemical, chemical foam, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Use agent most appropriate to extinguish fire.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Use with adequate ventilation. Avoid
contact with eyes, skin, and clothing. Empty containers retain
product residue, (liquid and/or vapor), and can be dangerous. Keep
container tightly closed. Keep away from heat, sparks and flame.
Avoid ingestion and inhalation. Do not pressurize, cut, weld, braze,
solder, drill, grind, or expose empty containers to heat, sparks or
open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 1438-91-1:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use. Follow the OSHA
respirator regulations found in 29 CFR 1910.134 or
European Standard EN 149. Use a NIOSH/MSHA or
European Standard EN 149 approved respirator if
exposure limits are exceeded or if irritation or
other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: light brown to dark brown
Odor: stench
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 64 - 65 deg C @ 15.00mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 63 deg C ( 145.40 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: 1.0700g/cm3
Molecular Formula: C6H8OS
Molecular Weight: 128.19
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stability unknown.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, oxides of sulfur, irritating and toxic fumes and
gases, carbon dioxide.
Hazardous Polymerization: Has not been reported
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 1438-91-1 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Furfuryl methyl sulfide -
Not listed by ACGIH, IARC, or NTP.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 28A After contact with skin, wash immediately with
plenty of water.
S 37 Wear suitable gloves.
S 37/39 Wear suitable gloves and eye/face
protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 1438-91-1: No information available.
Canada
CAS# 1438-91-1 is listed on Canada's DSL List.
CAS# 1438-91-1 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 1438-91-1 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 3/16/1999 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
1,3,5-Trichloro-2,4,6-Trifluorobenzene, 98%
| 319-88-0 |
|
Benzenesulfonyl fluoride, 99%
| 368-43-4 |
|
(S)-(+)-2-Phenylglycinol, 98%
| 20989-17-7 |
|
Ethyl Vinyl Sulfone, 98%
| 1889-59-4 |
|
Iodoacetic anhydride
| 54907-61-8 |
|
Ethyl phenyl sulfide, 97%
| 622-38-8 |
|
Indole-3-carboxylic acid, 99%
| 771-50-6 |
|
5-Acetyl-2,4-dimethylthiazole, 96%
| 38205-60-6 |
|
Ethyl Heptanoate, 99%
| 106-30-9 |
|
2-ETHYL-2-HEXENOIC ACID, 95%, PREDOMINANTLY TRANS
| 5309-52-4 |
|
Ethyl Isobutyrate, 99%
| 97-62-1 |
|
Furfuryl methyl sulfide, 97%
| 1438-91-1 |
|
trans-2-Hexenyl acetate, 98%
| 2497-18-9 |
|
2,5-Dimethyl-4-Hydroxy-3(2H)-Furanone, 95%
| 3658-77-3 |
|
Isobutyl Propionate, 98%
| 540-42-1 |
|
8-Mercaptomenthone, Mixture of Isomers, Tech., 80%
| 7732-18-5 |
|
Methyl propyl disulfide, 95%
| 2179-60-4 |
|
3-(Methylthio)-1-hexanol, 97%
| 51755-66-9 |
|
1,8-Octanedithiol, 99%
| 1191-62-4 |
|
Octyl acetate, 99+%
| 112-14-1 |
|
Poly(vinyl Stearate), Average MW ca. 90000 (GPC)
| 9003-95-6 |
|
Poly(2,6-Dimethyl-1,4-Phenylene Oxide)
| 25134-01-4 |
|
Polyacrylonitrile
| 25014-41-9 |
|
Poly(Ethylene Adipate), Average M.W. ca. 10.000 (GPC)
| 24937-78-8 |
|
Poly(methyl acrylate), solution in toluene, average MW ca. 40000
| 108-88-3 |
|
3-Chloropropyl acetate
| 628-09-1 |
|
Poly(Styrene-Co-Butadiene), 5% Styrene
| 9003-55-8 |
|
Poly(Vinyl Cinnamate), Average MW ca. 200000 (GPC)
| 9050-06-0 |
|
Poly(ethyl acrylate), approx. 20% solution in toluene, average M.W.
| 108-88-3 |
|
Poly(4-Methylstyrene), Average MW ca. 70000 (GPC)
| 24936-41-2 |
|
Poly(1-Butene), Isotactic, Average MW ca. 185000 (GPC)
| 9003-28-5 |
|
Polyethylene, Oxidized
| 68441-17-8 |
|
Poly(styrene-acrylonitrile), 25 wt.% acrylonitrile, average MW ca.
| 9003-54-7 |
|
Acenaphthylene, 99+%
| 208-96-8 |
|
Cyclohexyl Methacrylate, 97+%
| 101-43-9 |
|
4-Hydroxybutyl Acrylate, 96%
| 2478-10-6 |
|
Poly(acrylonitrile-co-butadiene-co-styrene)
| 9003-56-9 |
|
6-Methylnicotinic Acid, 99%
| 3222-47-7 |
|
Diphenyl Isophthalate, 99%
| 744-45-6 |
|
Diethyl Fluoromalonate, 97%
| 685-88-1 |
|
Phloretin, 98%
| 60-82-2 |
|
2,2,2-Trifluoroethyl Ether, 99%
| 333-36-8 |
|
Trifluoroacetic Acid Lithium Salt, 95%
| 2923-17-3 |
|
3,5-Bis(trifluoromethyl)benzaldehyde, 97%
| 401-95-6 |
|
3,5-Bis(Trifluoromethyl)Bromobenzene, 99%
| 328-70-1 |
|
3,5-Difluorobenzoic acid, 97%
| 455-40-3 |
|
3,5-Difluorobenzonitrile, 99%
| 64248-63-1 |
|
3,5-Difluorobenzoyl Chloride, 98%
| 129714-97-2 |
|
2,3-Difluorobenzyl Alcohol, 94%
| 75853-18-8 |
|
2,4-Difluorobenzyl alcohol, 99%
| 56456-47-4 |
|
|