Search   
MSDS 
:
 5-Acetyl-2,4-dimethylthiazole, 96%
CAS 
:
 38205-60-6
SYNONYMS 
:
 None
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 38205-60-6 |5-Acetyl-2,4-dimethylthiazole | 96.0 | 253-826-0 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37/38

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Irritating to eyes, respiratory system and skin.The toxicological
properties of this material have not been fully investigated.

Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. The toxicological properties of this substance have not
been fully investigated.
Inhalation:
Causes respiratory tract irritation. Causes irritation of mucous
membrane.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Flush skin with plenty of water for at least 15 minutes while
removing contaminated clothing and shoes. Get medical aid if
irritation develops or persists. Wash clothing before reuse.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.
Antidote:
None reported.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Vapors may
be heavier than air. They can spread along the ground and collect
in low or confined areas.
Extinguishing Media:
Use water spray to cool fire-exposed containers. Use extinguishing
media most appropriate for the surrounding fire. Use water spray, dry
chemical, carbon dioxide, or appropriate foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Provide
ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Avoid contact with eyes, skin, and clothing. Keep
container tightly closed. Avoid ingestion and inhalation. Use with
adequate ventilation. Wash clothing before reuse.
Storage:
Store in a cool place in the original container and protect from
sunlight. Store in a tightly closed container.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 38205-60-6:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use. Follow the OSHA
respirator regulations found in 29 CFR 1910.134 or
European Standard EN 149. Use a NIOSH/MSHA or
European Standard EN 149 approved respirator if
exposure limits are exceeded or if irritation or
other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: colorless to yellow
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 228 - 230 deg C
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 104 deg C ( 219.20 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: 1.1500g/cm3
Molecular Formula: C7H9NOS
Molecular Weight: 155.22

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable at room temperature in closed containers under normal storage
and handling conditions.
Conditions to Avoid:
Incompatible materials, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, carbon monoxide, oxides of sulfur, carbon dioxide.
Hazardous Polymerization: Has not been reported

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 38205-60-6 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
5-Acetyl-2,4-dimethylthiazole -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 37/39 Wear suitable gloves and eye/face
protection.
WGK (Water Danger/Protection)
CAS# 38205-60-6: No information available.
Canada
CAS# 38205-60-6 is listed on Canada's DSL List.
CAS# 38205-60-6 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 38205-60-6 is not listed on the TSCA inventory.
It is for research and development use only.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 4/06/1999 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
1,3,5-Trichloro-2,4,6-Trifluorobenzene, 98% 319-88-0
Benzenesulfonyl fluoride, 99% 368-43-4
(S)-(+)-2-Phenylglycinol, 98% 20989-17-7
Ethyl Vinyl Sulfone, 98% 1889-59-4
Iodoacetic anhydride 54907-61-8
Ethyl phenyl sulfide, 97% 622-38-8
Indole-3-carboxylic acid, 99% 771-50-6
5-Acetyl-2,4-dimethylthiazole, 96% 38205-60-6
Ethyl Heptanoate, 99% 106-30-9
2-ETHYL-2-HEXENOIC ACID, 95%, PREDOMINANTLY TRANS 5309-52-4
Ethyl Isobutyrate, 99% 97-62-1
Furfuryl methyl sulfide, 97% 1438-91-1
trans-2-Hexenyl acetate, 98% 2497-18-9
2,5-Dimethyl-4-Hydroxy-3(2H)-Furanone, 95% 3658-77-3
Isobutyl Propionate, 98% 540-42-1
8-Mercaptomenthone, Mixture of Isomers, Tech., 80% 7732-18-5
Methyl propyl disulfide, 95% 2179-60-4
3-(Methylthio)-1-hexanol, 97% 51755-66-9
1,8-Octanedithiol, 99% 1191-62-4
Octyl acetate, 99+% 112-14-1
Poly(vinyl Stearate), Average MW ca. 90000 (GPC) 9003-95-6
Poly(2,6-Dimethyl-1,4-Phenylene Oxide) 25134-01-4
Polyacrylonitrile 25014-41-9
Poly(Ethylene Adipate), Average M.W. ca. 10.000 (GPC) 24937-78-8
Poly(methyl acrylate), solution in toluene, average MW ca. 40000 108-88-3
3-Chloropropyl acetate 628-09-1
Poly(Styrene-Co-Butadiene), 5% Styrene 9003-55-8
Poly(Vinyl Cinnamate), Average MW ca. 200000 (GPC) 9050-06-0
Poly(ethyl acrylate), approx. 20% solution in toluene, average M.W. 108-88-3
Poly(4-Methylstyrene), Average MW ca. 70000 (GPC) 24936-41-2
Poly(1-Butene), Isotactic, Average MW ca. 185000 (GPC) 9003-28-5
Polyethylene, Oxidized 68441-17-8
Poly(styrene-acrylonitrile), 25 wt.% acrylonitrile, average MW ca. 9003-54-7
Acenaphthylene, 99+% 208-96-8
Cyclohexyl Methacrylate, 97+% 101-43-9
4-Hydroxybutyl Acrylate, 96% 2478-10-6
Poly(acrylonitrile-co-butadiene-co-styrene) 9003-56-9
6-Methylnicotinic Acid, 99% 3222-47-7
Diphenyl Isophthalate, 99% 744-45-6
Diethyl Fluoromalonate, 97% 685-88-1
Phloretin, 98% 60-82-2
2,2,2-Trifluoroethyl Ether, 99% 333-36-8
Trifluoroacetic Acid Lithium Salt, 95% 2923-17-3
3,5-Bis(trifluoromethyl)benzaldehyde, 97% 401-95-6
3,5-Bis(Trifluoromethyl)Bromobenzene, 99% 328-70-1
3,5-Difluorobenzoic acid, 97% 455-40-3
3,5-Difluorobenzonitrile, 99% 64248-63-1
3,5-Difluorobenzoyl Chloride, 98% 129714-97-2
2,3-Difluorobenzyl Alcohol, 94% 75853-18-8
2,4-Difluorobenzyl alcohol, 99% 56456-47-4

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net