Search   
MSDS 
:
 4-Hydroxybutyl Acrylate, 96%
CAS 
:
 2478-10-6
SYNONYMS 
:
 None.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 2478-10-6 |4-Hydroxybutyl Acrylate | 96% | 219-606-3 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37/38

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Irritating to eyes, respiratory system and skin.Light sensitive.Heat
sensitive.The toxicological properties of this material have not been
fully investigated.

Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. The toxicological properties of this substance have not
been fully investigated.
Inhalation:
Causes respiratory tract irritation. The toxicological properties of
this substance have not been fully investigated.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and
drink 2-4 cupfuls of milk or water. Wash mouth out with water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Use water
spray to keep fire-exposed containers cool. Vapors may be heavier
than air. They can spread along the ground and collect in low or
confined areas. Containers may explode when heated.
Extinguishing Media:
Use agent most appropriate to extinguish fire. Cool containers with
flooding quantities of water until well after fire is out. Use water
spray, dry chemical, carbon dioxide, or appropriate foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Avoid contact with eyes, skin, and clothing. Keep container tightly
closed. Avoid ingestion and inhalation. Use with adequate
ventilation. Store protected from light. Wash clothing before reuse.
Storage:
Keep away from heat and flame. Do not store in direct sunlight.
Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances. Keep
refrigerated. (Store below 4C/39F.) Store protected from light.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 2478-10-6:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: gold
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 95 deg C @ 0.1mmHg
Freezing/Melting Point: Not available.
Autoignition Temperature: 380 deg C ( 716.00 deg F)
Flash Point: 130 deg C ( 266.00 deg F)
Explosion Limits, lower: 1.80 vol %
Explosion Limits, upper: 10.00 vol %
Decomposition Temperature:
Solubility in water: soluble
Specific Gravity/Density: 1.0410g/cm3
Molecular Formula: H2C=CHCO2(CH2)4OH
Molecular Weight: 144.17

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable at room temperature in closed containers under normal storage
and handling conditions.
Conditions to Avoid:
Incompatible materials, light, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide.
Hazardous Polymerization: May occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 2478-10-6 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
4-Hydroxybutyl Acrylate -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 37/39 Wear suitable gloves and eye/face
protection.
WGK (Water Danger/Protection)
CAS# 2478-10-6: 1
Canada
CAS# 2478-10-6 is listed on Canada's DSL List.
CAS# 2478-10-6 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 2478-10-6 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 4/06/1999 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
1,3,5-Trichloro-2,4,6-Trifluorobenzene, 98% 319-88-0
Benzenesulfonyl fluoride, 99% 368-43-4
(S)-(+)-2-Phenylglycinol, 98% 20989-17-7
Ethyl Vinyl Sulfone, 98% 1889-59-4
Iodoacetic anhydride 54907-61-8
Ethyl phenyl sulfide, 97% 622-38-8
Indole-3-carboxylic acid, 99% 771-50-6
5-Acetyl-2,4-dimethylthiazole, 96% 38205-60-6
Ethyl Heptanoate, 99% 106-30-9
2-ETHYL-2-HEXENOIC ACID, 95%, PREDOMINANTLY TRANS 5309-52-4
Ethyl Isobutyrate, 99% 97-62-1
Furfuryl methyl sulfide, 97% 1438-91-1
trans-2-Hexenyl acetate, 98% 2497-18-9
2,5-Dimethyl-4-Hydroxy-3(2H)-Furanone, 95% 3658-77-3
Isobutyl Propionate, 98% 540-42-1
8-Mercaptomenthone, Mixture of Isomers, Tech., 80% 7732-18-5
Methyl propyl disulfide, 95% 2179-60-4
3-(Methylthio)-1-hexanol, 97% 51755-66-9
1,8-Octanedithiol, 99% 1191-62-4
Octyl acetate, 99+% 112-14-1
Poly(vinyl Stearate), Average MW ca. 90000 (GPC) 9003-95-6
Poly(2,6-Dimethyl-1,4-Phenylene Oxide) 25134-01-4
Polyacrylonitrile 25014-41-9
Poly(Ethylene Adipate), Average M.W. ca. 10.000 (GPC) 24937-78-8
Poly(methyl acrylate), solution in toluene, average MW ca. 40000 108-88-3
3-Chloropropyl acetate 628-09-1
Poly(Styrene-Co-Butadiene), 5% Styrene 9003-55-8
Poly(Vinyl Cinnamate), Average MW ca. 200000 (GPC) 9050-06-0
Poly(ethyl acrylate), approx. 20% solution in toluene, average M.W. 108-88-3
Poly(4-Methylstyrene), Average MW ca. 70000 (GPC) 24936-41-2
Poly(1-Butene), Isotactic, Average MW ca. 185000 (GPC) 9003-28-5
Polyethylene, Oxidized 68441-17-8
Poly(styrene-acrylonitrile), 25 wt.% acrylonitrile, average MW ca. 9003-54-7
Acenaphthylene, 99+% 208-96-8
Cyclohexyl Methacrylate, 97+% 101-43-9
4-Hydroxybutyl Acrylate, 96% 2478-10-6
Poly(acrylonitrile-co-butadiene-co-styrene) 9003-56-9
6-Methylnicotinic Acid, 99% 3222-47-7
Diphenyl Isophthalate, 99% 744-45-6
Diethyl Fluoromalonate, 97% 685-88-1
Phloretin, 98% 60-82-2
2,2,2-Trifluoroethyl Ether, 99% 333-36-8
Trifluoroacetic Acid Lithium Salt, 95% 2923-17-3
3,5-Bis(trifluoromethyl)benzaldehyde, 97% 401-95-6
3,5-Bis(Trifluoromethyl)Bromobenzene, 99% 328-70-1
3,5-Difluorobenzoic acid, 97% 455-40-3
3,5-Difluorobenzonitrile, 99% 64248-63-1
3,5-Difluorobenzoyl Chloride, 98% 129714-97-2
2,3-Difluorobenzyl Alcohol, 94% 75853-18-8
2,4-Difluorobenzyl alcohol, 99% 56456-47-4

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net