Search   
MSDS 
:
 Poly(acrylonitrile-co-butadiene-co-styrene)
CAS 
:
 9003-56-9
SYNONYMS 
:
 2-Propenitrile, polymer with 1,3-butadiene and ethenylbenzene.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 9003-56-9 |Poly(acrylonitrile-butadiene-styrene) | 100 | unlisted |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: T
Risk Phrases: 20/21/22 45

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Harmful by inhalation, in contact with skin and if swallowed. May
cause cancer.

Potential Health Effects
Eye:
May cause eye irritation. The toxicological properties of this
material have not been fully investigated.
Skin:
May cause skin irritation. The toxicological properties of this
material have not been fully investigated.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. The toxicological properties of this substance have not
been fully investigated.
Inhalation:
May cause respiratory tract irritation. The toxicological properties
of this substance have not been fully investigated.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Wash mouth out with water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Vapors may
be heavier than air. They can spread along the ground and collect
in low or confined areas.
Extinguishing Media:
Use agent most appropriate to extinguish fire. Use water spray, dry
chemical, carbon dioxide, or appropriate foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Forms smooth, slippery surfaces on floors, posing an accident risk.
Clean up spills immediately, observing precautions in the Protective
Equipment section. Sweep up or absorb material, then place into a
suitable clean, dry, closed container for disposal. Provide
ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Use with adequate ventilation. Avoid
contact with eyes, skin, and clothing. Keep container tightly closed.
Avoid ingestion and inhalation.
Storage:
Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Use adequate ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 9003-56-9:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Solid
Color: Not available.
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: Not available.
Autoignition Temperature: Not applicable.
Flash Point: Not applicable.
Explosion Limits, lower: N/A
Explosion Limits, upper: N/A
Decomposition Temperature:
Solubility in water: insoluble
Specific Gravity/Density:
Molecular Formula: C15H17N1x
Molecular Weight: 197.119

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Dust generation.
Incompatibilities with Other Materials:
Oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide.
Hazardous Polymerization: Has not been reported

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 9003-56-9: AT6970000
LD50/LC50:
Not available.
Carcinogenicity:
Poly(acrylonitrile-butadiene-styrene) -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: T
Risk Phrases:
R 45 May cause cancer.
R 20/21/22 Harmful by inhalation, in contact with
skin and if swallowed.
Safety Phrases:
S 53 Avoid exposure - obtain special instructions
before use.
S 28A After contact with skin, wash immediately with
plenty of water.
S 37 Wear suitable gloves.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 9003-56-9: No information available.
Canada
CAS# 9003-56-9 is listed on Canada's DSL List.
CAS# 9003-56-9 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 9003-56-9 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 8/04/1998 Revision #4 Date: 3/04/2004

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
1,3,5-Trichloro-2,4,6-Trifluorobenzene, 98% 319-88-0
Benzenesulfonyl fluoride, 99% 368-43-4
(S)-(+)-2-Phenylglycinol, 98% 20989-17-7
Ethyl Vinyl Sulfone, 98% 1889-59-4
Iodoacetic anhydride 54907-61-8
Ethyl phenyl sulfide, 97% 622-38-8
Indole-3-carboxylic acid, 99% 771-50-6
5-Acetyl-2,4-dimethylthiazole, 96% 38205-60-6
Ethyl Heptanoate, 99% 106-30-9
2-ETHYL-2-HEXENOIC ACID, 95%, PREDOMINANTLY TRANS 5309-52-4
Ethyl Isobutyrate, 99% 97-62-1
Furfuryl methyl sulfide, 97% 1438-91-1
trans-2-Hexenyl acetate, 98% 2497-18-9
2,5-Dimethyl-4-Hydroxy-3(2H)-Furanone, 95% 3658-77-3
Isobutyl Propionate, 98% 540-42-1
8-Mercaptomenthone, Mixture of Isomers, Tech., 80% 7732-18-5
Methyl propyl disulfide, 95% 2179-60-4
3-(Methylthio)-1-hexanol, 97% 51755-66-9
1,8-Octanedithiol, 99% 1191-62-4
Octyl acetate, 99+% 112-14-1
Poly(vinyl Stearate), Average MW ca. 90000 (GPC) 9003-95-6
Poly(2,6-Dimethyl-1,4-Phenylene Oxide) 25134-01-4
Polyacrylonitrile 25014-41-9
Poly(Ethylene Adipate), Average M.W. ca. 10.000 (GPC) 24937-78-8
Poly(methyl acrylate), solution in toluene, average MW ca. 40000 108-88-3
3-Chloropropyl acetate 628-09-1
Poly(Styrene-Co-Butadiene), 5% Styrene 9003-55-8
Poly(Vinyl Cinnamate), Average MW ca. 200000 (GPC) 9050-06-0
Poly(ethyl acrylate), approx. 20% solution in toluene, average M.W. 108-88-3
Poly(4-Methylstyrene), Average MW ca. 70000 (GPC) 24936-41-2
Poly(1-Butene), Isotactic, Average MW ca. 185000 (GPC) 9003-28-5
Polyethylene, Oxidized 68441-17-8
Poly(styrene-acrylonitrile), 25 wt.% acrylonitrile, average MW ca. 9003-54-7
Acenaphthylene, 99+% 208-96-8
Cyclohexyl Methacrylate, 97+% 101-43-9
4-Hydroxybutyl Acrylate, 96% 2478-10-6
Poly(acrylonitrile-co-butadiene-co-styrene) 9003-56-9
6-Methylnicotinic Acid, 99% 3222-47-7
Diphenyl Isophthalate, 99% 744-45-6
Diethyl Fluoromalonate, 97% 685-88-1
Phloretin, 98% 60-82-2
2,2,2-Trifluoroethyl Ether, 99% 333-36-8
Trifluoroacetic Acid Lithium Salt, 95% 2923-17-3
3,5-Bis(trifluoromethyl)benzaldehyde, 97% 401-95-6
3,5-Bis(Trifluoromethyl)Bromobenzene, 99% 328-70-1
3,5-Difluorobenzoic acid, 97% 455-40-3
3,5-Difluorobenzonitrile, 99% 64248-63-1
3,5-Difluorobenzoyl Chloride, 98% 129714-97-2
2,3-Difluorobenzyl Alcohol, 94% 75853-18-8
2,4-Difluorobenzyl alcohol, 99% 56456-47-4

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net