**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 7449-74-3 |N-Methyl-N-(trimethylsilyl)acetamide | 99 | 231-217-0 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: None Listed.
Risk Phrases: 10
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable.Moisture sensitive.The toxicological properties of this
material have not been fully investigated.
Potential Health Effects
Eye:
May cause eye irritation. May cause chemical conjunctivitis and
corneal damage.
Skin:
May cause irritation and dermatitis. May cause cyanosis of the
extremities.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. The toxicological properties of this substance have not
been fully investigated. Ingestion of large amounts may cause CNS
depression.
Inhalation:
May cause respiratory tract irritation. The toxicological properties
of this substance have not been fully investigated. Aspiration may
lead to pulmonary edema. Vapors may cause dizziness or suffocation.
May cause burning sensation in the chest.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Do NOT induce vomiting. If conscious and alert,
rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Will burn if involved in a fire. Use
water spray to keep fire-exposed containers cool. Containers may
explode in the heat of a fire. Flammable liquid and vapor. Vapors
may be heavier than air. They can spread along the ground and
collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT get water inside
containers. Do NOT use straight streams of water.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Remove all sources of ignition. Absorb spill using
an absorbent, non-combustible material such as earth, sand, or
vermiculite. Do not use combustible materials such as sawdust. Use a
spark-proof tool. Provide ventilation. Do not get water inside
containers. A vapor suppressing foam may be used to reduce vapors.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Use only in a well-ventilated area.
Ground and bond containers when transferring material. Use
spark-proof tools and explosion proof equipment. Avoid contact with
eyes, skin, and clothing. Empty containers retain product residue,
(liquid and/or vapor), and can be dangerous. Keep container tightly
closed. Keep away from heat, sparks and flame. Avoid ingestion and
inhalation. Do not allow contact with water. Do not pressurize, cut,
weld, braze, solder, drill, grind, or expose empty containers to
heat, sparks or open flames. Keep from contact with moist air and
steam.
Storage:
Keep away from heat, sparks, and flame. Store in a tightly closed
container. Store in a cool, dry, well-ventilated area away from
incompatible substances. Flammables-area. Store protected from
moisture.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 7449-74-3:
United Kingdom, WEL - TWA: (listed as silica, amorphous): 6 mg/m3
(inhalable dust); 2.4 mg/m3 TWA (respirable dust)
United Kingdom, WEL - STEL: (listed as silica, amorphous): 18 mg/
STEL (inhalable dust); 7.2 mg/m3 STEL (respirable dust)
Russia: (listed as silica, amorphous): 1 mg/m3 TWA
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Clear liquid
Color: clear light yellow
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 48.0 - 49.0 deg C @ 11.00mmHg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not applicable.
Flash Point: 48 deg C ( 118.40 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature: Not available.
Solubility in water: May decompose.
Specific Gravity/Density: .9040g/cm3
Molecular Formula: C6H15NOSi
Molecular Weight: 145.28
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, moisture, excess heat,
strong oxidants.
Incompatibilities with Other Materials:
Moisture, strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide.
Hazardous Polymerization: Will not occur.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 7449-74-3 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
N-Methyl-N-(trimethylsilyl)acetamide -
Not listed by ACGIH, IARC, or NTP.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: FLAMMABLE LIQUID, N.O.S.*
Hazard Class: 3
UN Number: 1993
Packing Group: III
IMO
Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Class: 3.3
UN Number: 1993
Packing Group: III
RID/ADR
Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Class: 3
UN Number: 1993
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: Not available.
Risk Phrases:
R 10 Flammable.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
WGK (Water Danger/Protection)
CAS# 7449-74-3: No information available.
Canada
CAS# 7449-74-3 is listed on Canada's NDSL List.
CAS# 7449-74-3 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 7449-74-3 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 9/02/1997 Revision #6 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Ytterbium, 99,9%, -12 mm
| 7440-64-4 |
|
5-Chloro-1-indanone, 98%
| 42348-86-7 |
|
2-Methyl-1-butanethiol, 95%
| 1878-18-8 |
|
2-Methyl-3-Nitrobenzyl Chloride
| 60468-54-4 |
|
3-Methoxypropylamine, 99+%
| 5332-73-0 |
|
Eicosane, 99%
| 112-95-8 |
|
3-Benzylpyridine, 97%
| 620-95-1 |
|
Chloro-(chloromethyl)-dimethylsilane, 98%
| 1719-57-9 |
|
Rhodium on 1/8-inch alumina pellets ( 0.5% rh)
| |
|
3-Methyl-1-hexene, 99%
| 3404-61-3 |
|
4-Fluorobenzimidazole-2-carboxylic acid
| 83431-74-7 |
|
(S)-(-)-5-(Hydroxymethyl)-2(5H)-furanone, 99% (99% e.e.)
| 78508-96-0 |
|
2-Acetylthiophene, 98%, Balance Mainly 3-Acetylthiophene
| 88-15-3 |
|
Phenylphosphinic acid sodium salt (50% aqueous solution), 46% (titr.)
| 4297-95-4 |
|
m-(Hydrazinosulfonyl)benzoic acid, 99%
| 7385-52-6 |
|
2-Hydroxyquinoline, 99% (UV-VIS)
| 59-31-4 |
|
Acrylamido Glycolic Acid, Anhydrous, 98%
| 6737-24-2 |
|
Naphthalene-d8, 98+ atom % D
| 1146-65-2 |
|
N-Ethyl-m-toluidine, 99+%
| 102-27-2 |
|
Thiazole, 99%
| 288-47-1 |
|
Ferrozine Iron Reagent, Monohydrate, 95+% (UV-Vis)
| 69898-45-9 |
|
1-(4-Methoxyphenyl)-2-methylpiperazine
| 35947-12-7 |
|
7-(2-Chloroethyl)-Theophylline, 97%
| 5878-61-5 |
|
Ammonium Hexabromoplatinate(IV), 99.99%
| 17363-02-9 |
|
2,3-Dibromopropanol, 96%
| 96-13-9 |
|
4-(Methylamino)butyric acid hydrochloride, 99%
| 6976-17-6 |
|
1,3-Propanediol, 98%
| 504-63-2 |
|
2-Fluorobenzylamine, 96%
| 89-99-6 |
|
L-Arabinose
| 5328-37-0 |
|
4-N,N-Dimethylaminoazobenzene-4'-isothiocyanate
| 7612-98-8 |
|
DL-aspartic acid magnesium salt tetrahydrate, 98%
| 215528-79-3 |
|
2-(Diisopropylamino)ethyl Chloride Hydro-Chloride, 97%
| 4261-68-1 |
|
5-Methoxysalicylic Acid, 98%
| 2612-02-4 |
|
1,2-Benzisoxazole, 95%
| 271-95-4 |
|
2,2'-(1,2-Ethenediyldi-4,1-Phenylene)- Bisbenzoxazole
| 1533-45-5 |
|
6,7-Dimethoxy-1,2,3,4-Tetrahydroisoquinoline-1-Thione, 99%
| 24456-59-5 |
|
3,3'-Dichloropivalic Acid, 99%
| 67329-11-7 |
|
3-Indoleacrylic acid, 99%
| 1204-06-4 |
|
1,2,3,6,7,8-Hexahydropyrene,98%
| 1732-13-4 |
|
9H-fluorene-4-carboxylic acid, 96%
| 6954-55-8 |
|
Methylamine Hydrochloride, P.A.
| 593-51-1 |
|
Potassium superoxide (chunks)
| 12030-88-5 |
|
N-Methyl-N-(trimethylsilyl)acetamide, 99%
| 7449-74-3 |
|
1-[4,4-Bis(4-fluorophenyl)butyl]piperazine
| 5631-35-6 |
|
2-(2-Hydroxyethyl)Pyridine, 99%
| 103-74-2 |
|
Scandium(iii)nitrate hydrate, 99.9%
| |
|
9,10-Diphenylanthracene, 99%
| 1499-10-1 |
|
Nocodazole 99+%
| 31430-18-9 |
|
1-Octanesulfonic Acid Sodium Salt, 99+%, HPLC Grade anhydrous
| 5324-84-5 |
|
Barium perchlorate, anhydrous, 99%
| 13465-95-7 |
|
|