Search   
MSDS 
:
 Poly(ethylene), low density, average m.w.50000
CAS 
:
 9002-88-4
SYNONYMS 
:
 None.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 9002-88-4 |Poly(ethylene), low density, Average M| 100.0 | 200-849-9 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: None Listed.
Risk Phrases: None Listed.

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
The toxicological properties of this material have not been fully
investigated.

Potential Health Effects
Eye:
May cause eye irritation.
Skin:
May cause skin irritation.
Ingestion:
May cause irritation of the digestive tract. The toxicological
properties of this substance have not been fully investigated.
Inhalation:
May cause respiratory tract irritation. The toxicological properties
of this substance have not been fully investigated.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
If swallowed, do not induce vomiting unless directed to do so by
medical personnel. Never give anything by mouth to an unconscious
person. Get medical aid.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.
Antidote:
None reported.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Will burn
if involved in a fire.
Extinguishing Media:
In case of fire, use water, dry chemical, chemical foam, or
alcohol-resistant foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Vacuum or sweep up material and place into a suitable disposal
container. Clean up spills immediately, observing precautions in the
Protective Equipment section. Avoid generating dusty conditions.
Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use with adequate ventilation. Minimize dust
generation and accumulation. Avoid contact with eyes, skin, and
clothing. Keep container tightly closed. Avoid ingestion and
inhalation.
Storage:
Store in a cool, dry, well-ventilated area away from incompatible
substances. Keep containers tightly closed.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 9002-88-4:

Russia: 10 mg/m3 TWA

Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Solid
Color: white
Odor: odorless
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: 130.00 - 145.00 deg C
Autoignition Temperature: Not available.
Flash Point: > 231 deg C (> 447.80 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: Insoluble.
Specific Gravity/Density: .9200g/cm3
Molecular Formula:
Molecular Weight:

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Dust generation, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, carbon dioxide, acrid smoke and fumes.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 9002-88-4: KX3270000 TQ3325000
LD50/LC50:
CAS# 9002-88-4: Inhalation, mouse: LC50 = 12 gm/m3/30M.
Carcinogenicity:
Poly(ethylene), low density, Average M.W.50.000 -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: Not available.
Risk Phrases:
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 9002-88-4: 1
Canada
CAS# 9002-88-4 is listed on Canada's DSL List.
CAS# 9002-88-4 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 9002-88-4 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 12/08/1998 Revision #2 Date: 2/24/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Zinc, Granular, 20 Mesh, P.A. 7440-66-6
Zinc, Granular, 30 Mesh, P.A. 7440-66-6
Zinc, Dust (Pract) 7440-66-6
Beta-Ionone, Synthetic, 98% 14901-07-6
Beta-Ionone, 96% (Titr.) 14901-07-6
Allyl Alcohol, 99% 107-18-6
3,3'-Dimethoxybenzidine dihydrochloride, 99% 20325-40-0
Pyridoxine Hydrochloride, 99.0-101.0% (Dry Substance) 58-56-0
4-Nitrophenyl Chloroformate, 97% 7693-46-1
Methyl Oleate 112-62-9
Ethyl iodoacetate, 98% 623-48-3
2-Hydroxyisobutyric acid, 98% 594-61-6
Basic Fuchsin (Cert) 632-99-5
Ethylene/vinyl acetate copolymer 14% vinyl acetate 24937-78-8
Methacrolein, 90-95%(GC), stabilized with hydroquinone 78-85-3
Ethylene/vinyl acetate copolymer 25% vinyl acetate, average 24937-78-8
Ethylene/vinyl acetate copolymer 28% vinyl acetate, avge.m.w.285.000 24937-78-8
Ethylene/vinyl acetate copolymer, pellets, avr. m.w.110000, stab. 24937-78-8
Ammonium sulfobetaine - 1
2-Aminopyridine 504-29-0
D,L-Buthionine, 97% 3343-64-4
2-Chloroethanol, 99% 107-07-3
Resazurin, sodium salt, high purity biological stain 62758-13-8
Phenyl isocyanate, 99% 103-71-9
Triethanolamine hydrochloride, p.a. 637-39-8
Allyl Chloride, 98% 107-05-1
2-Hydroxyethyl methacrylate, 96%, stabilized with 200-400 ppm MEHQ 150-76-5
Poly(ethylene), low density, average m.w.50000 9002-88-4
Tributylborane, 1M solution in THF 109-99-9
Polysulfone Resin. Nominal M.W. 75000, (GPC) , Pellets 25135-51-7
4-Chlorophenol, 98% 106-48-9
4-Chlorophenol (Pract) 106-48-9
Trichloroacetonitrile, 98% 545-06-2
3-Diethylamino-1-propanol, 97% 622-93-5
1,6-Hexanediol, 99% -Total C6-Diols 629-11-8
Fullerene c60, 99.9+% (hplc) 99685-96-8
Fullerene c-60 99685-96-8
1H-Tetrazole, 98% 288-94-8
1,2,3,4-Tetrahydro-6,7-isoquinolinediol hy drobromide, 98% 52768-23-7
3,4-Dimethylphenylhydrazine Hydrochloride, 98% 60481-51-8
Ethyl p-toluenesulfonate, 98% 80-40-0
Dl-mandelic acid, 98+% 611-72-3
Phenanthrene, 98+% 85-01-8
Phenanthrene, fluorescent grade, 98% (uv-vis) 85-01-8
Dipropyl adipate 106-19-4
Aniline blue, water soluble, high purity biological stain 28631-66-5
L(-)-Malic acid, 99% 97-67-6
Bromothymol blue, water soluble indicator 34722-90-2
Bromocresol Green, Water Soluble, Indicator 67763-24-0
Bromophenol Blue Indicator 115-39-9

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net