HERNON MANUFACTURING
121 TECH DRIVE
SANFORD, FL 32771
(407) 322-4000
FAX: (407) 321-9700
For Emergency 1-800-255-3924
MATERIAL SAFETY DATA SHEET Page 1 of 3
PRODUCT IDENTIFICATION
Product Name: Fusion Bond 371
Product Type: Acrylic
II. COMPOSITION
Ingredients %
Part A
Methyl Methacrylate 70-80
Vinyl Resin 15-20
Methacrylic Acid 5-10
Part B
Methyl Methacrylate 70-80
Vinyl Resin 15-20
PDHP 5-10
* This component is listed as a SARA Section 313 Toxic Chemical
III. CHEMICAL AND PHYSICAL PROPERTIES
Vapor Pressure: 29 mmHg @ 68
Vapor Density: 3.5
Solubility in Water: Moderate
Specific Gravity: Part A: 0.972 Part B: 0.948
214oF
Boiling Point:
Volatile Organic Compound
(EPA Method 24) Not determined
Evaporation Rate (Ether = 1) NA
Appearance: Part A: White Part B: Cream
pH: NA
Odor: Mild
IV. FLAMMABILITY AND EXPLOSIVE PROPERTIES
51oF
Flash Point: Method: Tag Closed Cup
Estimated NFPA Code:
Health Hazard: 2
Fire Hazard: 3
Reactivity Hazard: 2
Specific Hazard: None
Estimated HMIS Code:
Health Hazard: 2
Flammability Hazard: 3
Reactivity Hazard: 2
Personal Protection: See Section X
Explosive Limits:
(% by volume in air) Lower 2
(% by volume in air) Upper 12.5
Recommended Extinguishing Agents: Water, carbon dioxide, dry chemical and foam
Hazardous Products Formed by Fire
or Thermal Decomp: Carbon monoxide, carbon dioxide, oxide of nitrogen, hydrocarbon, toxic vapors
Unusual Fire or Explosion Hazards: Avoid extreme heat
Compressed Gases: None
Pressure at Room Temp.: NA
HERNON MANUFACTURING
121 TECH DRIVE
SANFORD, FL 32771
(407) 322-4000
FAX: (407) 321-9700
For Emergency 1-800-255-3924
MATERIAL SAFETY DATA SHEET Page 2 of 3
Product Name: Fusion Bond 371
Product Type: Acrylic
V. SPILL OR LEAK AND DISPOSAL PROCEDURES
Steps to be taken in case of spill or leak:
Recommended methods of disposal:
VI. STORAGE AND HANDLING PROCEDURES
Storage: Store in a cool place. Store away from flammable and combutsible material. Store away from heat. Keep
container
Closed when not in use.
Handling: Contents may be under pressure, open carefully
VII. SHIPPING REGULATIONS
DOT (49 CFR 172) Consumer Commodity, ORM-D (not more than 1 Liter)
Proper Shipping Name Adhesives
Hazard Class or Division: Class 3, PG II
Identification Number UN1133
IATA
Proper Shipping Name: Adhesives
Class or Division: Class 3, PG II
UN or ID Number: UN1133
IMO
Substance Not available
Marine Pollutant Status Not available
Class Not available
Subsidiary Risk Label Not available
IMDG Code Page Not available
UN Number Not available
VIII. REACTIVITY DATA
Stability: Stable
Hazardous Polymerization: May occur
Hazardous Decomposition Products
(non-thermal): NA
Incompatibility: Peroxides, heat and flame
IX. EMERGENCY TREATMENT PROCEDURES
Ingestion: Do not induce vomiting. Drink two glasses of water. Call a physician
Inhalation: If signs/symptoms occur, remove person to fresh air. If signs/symptoms continue call a physician
Skin Contact: Wash affected area with soap and water
Eye Contact: Immediately flush eyes with large amounts of water. Get immediate medical attention.
X. PERSONAL PROTECTION
Eyes: Wear vented goggles. Wear safety glasses with side shields
Skin: Avoid skin contact/ Wear appropriate gloves such as gloves made of butyl rubber, polyvinyl alcohol or viton.
Ventilation: If exhaust ventilation is not adequate use half mask dust respirator, half mask organic vapor respirator, or full face
Organic respirator.
HERNON MANUFACTURING
121 TECH DRIVE
SANFORD, FL 32771
(407) 322-4000
FAX: (407) 321-9700
For Emergency 1-800-255-3924
MATERIAL SAFETY DATA SHEET Page 3 of 3
Product Name: Fusion Bond 371
Product Type: Acrylic
XI. HEALTH HAZARD DATA
Exposure Limits (TWA) ACGIH OSHA OTHER
Ingredients (TLV) (PEL)
A
410 mg/m3 410 mg/m3
Methyl Methacrylate 50 ppm
Vinyl Resin None None None
70 mg/m3 70 mg/m3
Methacrylic Acid None
Exposure Limits (STEL) ACGIH OSHA
Ingredients (TLV) (PEL)
Methyl Methacrylate 100 ppm
Ingredients for which no Exposure Limits have been established are not listed above.
Literature Referenced Carcinogen
Ingredients Target Organ and Other Health Effects NTP IARC OSHA
Methyl Methacrylate No Data NO NO NO
Vinyl Resin No Data NO NO NO
Methacrylic Acid No Data NO NO NO
PDHP No Data NO NO NO
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
XII. PREPARATION INFORMATION
Prepared by: Josef Arnon
Title: Technical Director
Company: Hernon Manufacturing, Inc., 121 Tech Drive, Sanford, FL 32771
Phone: (407) 322-4000
Emergency: 1-800-255-3924
Revision: 04/03
XIII. DISCLAIMER
Some of the information presented are from sources other than direct test data on the product itself. The information in this MSDS was
obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied,
regarding its correctness. The conditions or methods of handling, storage, use and disposal of the product are beyond our control and may
be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or
expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is
to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
This MSDS has been prepared in accordance with the requirements of the OSHA Hazard Communication Standard (29 CFR 1910.1200).
|