#496A
MATERIAL SAFETY DATA SHEET
NFPA RATING: Health = 1 Flammability = 0 Reactivity = 0
HMIS RATING: Health = / 1 Flammability = 0 Reactivity = 0
SECTION I 鈥? IDENTITY AND MANUFACTURER'S INFORMATION (521N-43A)
Manufacturer's Name: HILLYARD INDUSTRIES Product Name: COVER 2 (PART A)
Address: 302 North Fourth Street Date Prepared: September 15, 2004
St. Joseph, MO 64501 Prepared by: Regulatory Affairs Department
Emergency Telephone No.: (800) 424-9300 (Only in the event of chemical emergency involving a spill, leak, fire,
exposure or accident involving chemicals.) Other information calls: (816) 233-1321 (Ext. 8285)
SECTION II 鈥? INGREDIENTS/IDENTITY INFORMATION
Components
(Specific Chemical Identity: OTHER LIMITS
Common Name(s) CAS # OSHA PEL ACGIH TLV RECOMMENDED %
Water 7732-18-5 none none N.A. ---
Styrene Acrylic Copolymer Unknown not established not established N.A. ---
Emulsion to Hillyard
1-Phenoxy-2-Propanol 770-35-4 Not established Not established N.A. ---
Volatile Organic Compounds = 220 grams per liter/less water / Volatile Organic Substances = 0.54 pounds per gallon
SECTION III 鈥? PHYSICAL / CHEMICAL CHARACTERISTICS
Boiling Point: 214潞F Specific Gravity (H2O = 1): 25潞C = 1.03 39潞C = 1.03
Vapor Pressure (mm Hg.): 18.9 74.7
Percent Volatile by Volume (%):
Vapor Density (AIR = 1): 0.62 Evaporation Rate (ethyl ether = 1): slower than 1
complete Appearance and Odor: Milky white liquid; non-objectionable odor
Solubility in Water:
SECTION IV 鈥? FIRE AND EXPLOSION HAZARD DATA
Flash point: None to 200潞F (T.C.C.) Flammable Limits: LEL = N.A. UEL = N/A
Extinguishing Media: Water fog, foam, carbon dioxide, dry chemical, halogenated agents.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus with full facepiece and protective
clothing.
Unusual Fire and Explosion Hazards: None known to manufacturer
SECTION V 鈥? PHYSICAL HAZARDS
Stability: Stable Conditions to Avoid: Elevated temperatures
Incompatibility (Materials to Avoid): None known to manufacturer.
Hazardous Decomposition Products or Byproducts: When exposed to fire, produces smoke, soot, carbon
monoxide and carbon dioxide.
Hazardous Polymerization: Will not occur None known to Hillyard
Conditions to Avoid:
SECTION VI 鈥? HEALTH HAZARD DATA
Routes of entry: Inhalation? Yes Skin? Yes Ingestion? Yes
HEALTH HAZARDS (1. Acute and 2. Chronic)
1. Prolonged contact may cause skin irritation. Excessive exposure to vapors or spray mist can cause irritation of
the nose and throat. Not acutely toxic when administered orally at a dose level of 5.0 g./kg.; however, ingestion
may be harmful and cause irritation of the digestive tract. Inhalation - Not expected to be acutely toxic.
2. None known to Hillyard.
Chemical listed as Carcinogen or Potential Carcinogen:
National Toxicology Program = No I.A.R.C. Monographs = No OSHA = No
This product has no carcinogens listed by IARC, NTP, NIOSH, or ACGIH as of this date, greater than or equal to
0.1%.
Signs and Symptoms of Exposure: Prolonged skin contact may cause irritation. Excess inhalation may irritate
nose and throat. Ingestion may cause gastrointestinal irritation.
Medical Conditions Generally Aggravated by Exposure: None known to manufacturer.
page 2 of #496 鈥? Cover 2 (Part A)
SECTION VI 鈥? HEALTH HAZARD DATA continued
Emergency and First Aid Procedures: In case of eye contact, immediately flush with plenty of water for at leas 15
minutes. If redness, itching, or a burning sensation develops, have eyes examined and treated by medical personnel. In
case of skin contact, immediately flush skin with plenty of water for 15 minutes. If redness, itching, or burning sensation
develops, get medical attention. Wash contaminated clothing and decontaminate footwear before reuse. Ingestion: DO
NOT INDUCE VOMITING. Give one or more glasses of water to drink and refer to medical personnel, physician, or
poison control center. Never give anything by mouth to an unconscious person. Inhalation: Remove victim to fresh air.
If a cough or other respiratory symptoms develop, consult medical personnel.
SECTION VII 鈥? PRECAUTIONS FOR SAFE HANDLING AND USE
Steps To Be Taken In Case Material Is Released Or Spilled: Avoid breathing vapors. Ventilate area. Contain and
remove with inert absorbent and non-sparking tools.
Waste Disposal Method: Dispose of in accordance with state and federal regulations. Do not incinerate closed
container.
Precautions To Be Taken In Handling And Storing: Do not store above 100潞F. Keep containers closed when not in
use and upright to prevent leakage. Store in cool, well-ventilated area away from heat and out of direct sunlight. Protect
from freezing.
Other Precautions: Do not take internally, USE WITH ADEQUATE VENTILATION. Avoid breathing vapors or
spray mist. Open windows and doors, use exhaust fans or other means to insure fresh air entry during application and
drying. Avoid prolonged or repeated contact with skin. Refer to OSHA Standard 29 CFR 1910.94 for technical
guidelines on keeping air contamination below acceptable exposure limits.
SECTION VIII 鈥? CONTROL MEASURES
Respiratory Protection (Specify Type): None normally required when used according to label directions. Avoid
breathing spray mist. If sprayed, wear mechanical filter respirator to remove solid particles of overspray. Provide general
clean air dilution per good engineering practices.
Ventilation:
Local Exhaust = Not required Mechanical (General) = Recommended Special = N/A Other = N/A
with normal use
vinyl gloves if unable to avoid skin contact Eye Protection: Not necessary with normal use
Protective Gloves:
Other Protective Clothing or Equipment: None normally required. If unable to avoid prolonged or repeated contact
with skin, wear impervious clothing.
Work / Hygienic Practices: Wash thoroughly after handling. Upon contact remove contaminated clothing and shoes;
wash before reuse (including shoes).
SECTION IX 鈥? TRANSPORTATION INFORMATION
Applicable regulations: 49 CFR = No; IMCO = No; IATA = No
Proper shipping name: Varnish
UN No.: Not applicable; Limited Qty.: Not applicable; Hazard Class: Not applicable
Labels required: Not required DOT Exception: Not applicable
EPA Hazardous waste number / code: Not listed
Hazardous waste characteristics:
Ignitability = Not applicable; Corrosivity = Not applicable; Reactivity = Not applicable
DISCLAIMER OF WARRANTIES
NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, OR OF ANY NATURE ARE MADE WITH RESPECT TO THE PRODUCT(S) OR
INFORMATION CONTAINED IN THIS MATERIAL SAFETY DATA SHEET.
The information and recommendations contained in this Material Safety Data Sheet are supplied pursuant to 29 CFR
1910.1200 of the Occupational Safety and Health Standards Hazard Communication Rule. All information contained herein
is presented in good faith and is believed to be appropriate and accurate.
THE BUYER OR USER ASSUMES ALL RISKS ASSOCIATED WITH THE USE, MISUSE OR DISPOSAL OF THIS
PRODUCT. THE BUYER OR USER IS RESPONSIBLE TO COMPLY WITH ALL FEDERAL, STATE OR LOCAL
REGULATIONS CONCERNING THE USE, MISUSE OR DISPOSAL OF THESE PRODUCTS.
#496B
MATERIAL SAFETY DATA SHEET
NFPA RATING: Health = 3 Flammability = 1 Reactivity = 1
HMIS RATING: Health = 3 Flammability = 1 Reactivity = 1
SECTION I 鈥? IDENTITY AND MANUFACTURER'S INFORMATION (521N100A)
Manufacturer's Name: HILLYARD INDUSTRIES Product Name: COVER 2 (PART B)
Address: 302 North Fourth Street Date Prepared: June 30,2004
St. Joseph, MO 64501 Prepared by: Regulatory Affairs Department
Emergency Telephone No.: (800) 424-9300 (Only in the event of chemical emergency involving a spill, leak, fire, exposure or
accident involving chemicals.) Other information calls: (816) 233-1321 (Ext. 8285)
SECTION II 鈥? INGREDIENTS/IDENTITY INFORMATION
Components
(Specific Chemical Identity: OTHER LIMITS
Common Name(s) CAS# OSHA PEL ACGIH TLV RECOMMENDED %
Water 7732-18-5 none none N/A ---
Polyfunctional aziridine 64265-57-2 NA NA N/A 99.7%
75-55-8 2ppm 5 mg/m3
Propyleneimine 2 ppm 2ppm 5 mg/m3 <0.00005
per NIOSH
SECTION III 鈥? PHYSICAL / CHEMICAL CHARACTERISTICS
No data Specific Gravity (H2O = 1): 25潞C = 1.07 39潞C = 1.07
Boiling Point:
Vapor Pressure (mm Hg.): negligible No data
Percent Volatile by Volume (%):
>1 Evaporation Rate (ethyl ether = 1): slower than 1
Vapor Density (AIR = 1):
complete White emulsion; non-objectionable odor
Solubility in Water: Appearance and Odor:
SECTION IV 鈥? FIRE AND EXPLOSION HAZARD DATA
Flash point: >200.01 (P.M.C.C.) Flammable Limits: LEL = not determined UEL = N/A
Extinguishing Media: Carbon dioxide, dry chemical, halogenated agents. Water may be used to cool closed containers to prevent
pressure buildup.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus with full facepiece and full protective clothing. If
contact occurs with material or its solutions, immediately flush with water and remove contaminated clothing.
Unusual Fire and Explosion Hazards: Heat/impurities may increase temperature/build pressure/rupture closed containers,
spreading fire, increasing risk of burns/injuries.
SECTION V 鈥? PHYSICAL HAZARDS
Stability: unstable Avoid elevated temperatures and pressures or may react with
Conditions to Avoid:
water or acids with some release of energy, but not violently.
Incompatibility (Materials to Avoid): Avoid contamination with acidic materials, heat, direct sunlight, ultraviolet radiation, strong
oxidizing conditions and freezing conditions.
Hazardous Decomposition Products or Byproducts: Thermal decomposition may produce many various hydrocarbons and
irritating, vapors.
Hazardous Polymerization: Will not occur Conditions to Avoid: Freezing temperatures <32潞C
SECTION VI 鈥? HEALTH HAZARD DATA
Routes of entry: Inhalation? Yes Skin? Yes Ingestion? no
HEALTH HAZARDS (1. Acute and 2. Chronic)
1.This product is an eye corrosive based on animal studies. This product is a moderate skin irritant based on animal
studies. This product induced skin sensitization in an animal study. This product may induce skin sensitization in
humans. The acute oral toxicity of this material is between 500 and 50000 mg./kg. Relative to other materials this
material is classified as slightly toxic by ingestion. In humans, irritation of the mouth, pharynx, esophagus, and stomach
can develop following ingestion of this material. Vapors and/or aerosols of this material will probably irritate mucous
membranes, eyes, nose, and respiratory passages. This material may induce respiratory allergy/sensitization. Symptoms
include: cough, tightness in chest, and/or asthmatic wheezing. 2. None known to manufacturer on reacted product (after
part A and B are mixed). Unreacted Part B should be treated as a potential carcinogen. Aziridine based crosslinkers
caused mutations and chromosomal aberrations in several in vitro and in vivo genotoxicity studies. Based on these
studies and animal carcinogenicity data on similar substances, this material should be treated as a potential carcinogen.
Chemical listed as Carcinogen or Potential Carcinogen:
National Toxicology Program = No I.A.R.C. Monographs = No OSHA = No
Signs and Symptoms of Exposure: Product is a skin irritant and eye corrosive. Skin sensitizer. Ingestion will cause gastrointestinal
irritation. It is a respiratory sensitizer and irritant. Symptoms are cough, tightness in chest, and/or asthmatic wheezing.
Medical Conditions Generally Aggravated by Exposure: Medical personnel should evaluate persons with chronic pulmonary disease
before those workers handle this product.
page 2 of #496 鈥? Cover 2 (Part B)
SECTION VI 鈥? HEALTH HAZARD DATA cont.
Emergency and First Aid Procedures: Inhalation - Remove victim to fresh air. If not breathing, give artificial respiration, preferably
mouth-to-mouth. Consult medical personnel. If breathing is labored, give oxygen. Skin contact 鈥? Wash off skin with plenty of soap and
water. If redness, itching or burning sensation develops, get medical attention. Wash contaminated clothing and decontaminate footwear
before reuse. Eye contact 鈥? Immediately flush the eyes with large quantities of running water for a minimum of 15 minutes. Hold the
eyelids apart during the flushing to ensure rinsing of the entire surface of the eye and lids with water. Do not attempt to neutralize with
chemical agents. Obtain medical attention as soon as possible. Oils or ointments should not be used at this time. Continue the flushing for
an additional 15 minutes if a physician is not immediately available. Ingestion 鈥? DO NOT INDUCE VOMITING. Give one or two glasses
of water to drink and refer to medical personnel or take direction from either a physician or poison control center. Never give anything by
mouth to an unconscious person.
SECTION VII 鈥? PRECAUTIONS FOR SAFE HANDLING AND USE
Steps To Be Taken In Case Material Is Released Or Spilled: Wear skin, eye, and respiratory protection during cleanup. Contain spill.
Soak up material with absorbent and shovel into a chemical waste container. Decontaminate with 1% acetic acid solution or one part white
vinegar to four parts water. Keep spills and cleaning runoffs out of municipal sewers and open bodies of water.
Waste Disposal Method: Spills should be picked up with wet vac or absorbent material. Dispose of liquid per federal, state and local
regulations. Waste from normal product use may be sewered to a public-owned treatment works (POTW) in compliance with applicable
federal, state and local requirements. This product does not contain any chemicals subject to the reporting requirements of SARA Section
313. Discarded product is not a hazardous waste under EPA RCRA, but may be regulated by other jurisdictions.
Precautions To Be Taken In Handling And Storing: Freezing of product may rupture container. Product shelf life is best retained by
storage at 45-100掳F temperatures. Protect from freezing. Untreated material should not be released to the environment. Container disposal:
Empty container retains potentially hazardous residue. Observe all hazard precautions. May contain corrosive material. Do not distribute,
make available, furnish or reuse empty container except for storage and shipment of original product. Remove all product residue from
container and puncture or otherwise destroy empty container before disposal.
Other Precautions: Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. USE ONLY WITH
ADEQUATE VENTILATION. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you
experience eye watering, headache, or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an
appropriate, properly fitted respirator (NIOSH/MSHA approved) during and after application. Follow respirator manufacturer鈥檚 directions
for respirator use. Close container after each use. Avoid contact with eyes, skin, or clothing. Wash thoroughly after handling. Do not take
internally. A sensitized individual should not be exposed to the product which caused the sensitization. Keep container tightly sealed.
Store in a cool, well ventilated area away from heat, sources of ignition, direct sunlight, and acidic materials, anhydrides and strong
oxidizers. Avoid contamination with acidic materials, heat, direct sunlight, ultraviolet radiation, strong oxidizing conditions and freezing
conditions.
SECTION VIII 鈥? CONTROL MEASURES
Respiratory Protection (Specify Type): Good general ventilation should be sufficient to control airborne levels of irritating vapors. Spray
application is not recommended by Hillyard. Engineering measures: while Part B has a very low vapor pressure, precluding significant
inhalation exposure under normal conditions, uses which may generate aerosol mist , such as spray application, need to be well controlled
to prevent significant inhalation exposure, which presents serious health risks such as respiratory sensitization. Where aerosol mist may be
generated, the operation should be enclosed as much as possible, with extraction ventilation provided at any required openings. A properly
engineered spray booth, equipped with downdraft or lateral flow ventilation, is a possible engineering control measure. Air exhausted from
the enclosure should be filtered and discharged to a safe location, preferably outdoors.
Ventilation:
N/A Mechanical (General) = Adequate ventilation required Special = N/A Other = N/A
Local Exhaust =
Protective Gloves: Rubber, nitrile or neoprene gloves to prevent Eye Protection: Wear chemical tight goggles and full faceshield
skin contact. where splashing is a concern.
Other Protective Clothing or Equipment: Eyewash station and safety shower in work area. Use gloves, arm covers, and apron that has
been determined to be impervious und the conditions of use.
Work / Hygienic Practices: Wash hands before eating or using washroom.
SECTION IX 鈥? TRANSPORTATION INFORMATION
Applicable regulations: 49 CFR = noU; IMCO = noU; IATA = noU
U U U
Proper shipping name: VanishU UN No.: not applicableU; Limited Qty.: not applicableU; Hazard Class: not applicableU
U U U U
Labels required: not requiredU DOT Exception: not applicableU EPA Hazardous waste number / code: not listed
U U U
Hazardous waste characteristicsU:
Ignitability = not applicableU; Corrosivity = not applicableU; Reactivity = not applicableU
U U U
DISCLAIMER OF WARRANTIES
NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OF ANY NATURE ARE MADE WITH RESPECT TO THE PRODUCT(S) OR INFORMATION CONTAINED IN THIS MATERIAL
SAFETY DATA SHEET. The information and recommendations contained in this Material Safety Data Sheet are supplied pursuant to 29 CFR 1910.1200
of the Occupational Safety and Health Standards Hazard Communication Rule. All information contained herein is presented in good faith and is believed
to be appropriate and accurate.
THE BUYER OR USER ASSUMES ALL RISKS ASSOCIATED WITH THE USE, MISUSE OR DISPOSAL OF THIS PRODUCT. THE BUYER OR
USER IS RESPONSIBLE TO COMPLY WITH ALL FEDERAL, STATE OR LOCAL REGULATIONS CONCERNING THE USE, MISUSE OR
DISPOSAL OF THESE PRODUCTS.
#496 A & B
MATERIAL SAFETY DATA SHEET
NFPA RATING: Health = 1 Flammability = 0 Reactivity = 0
HMIS RATING: Health = / 1 Flammability = 0 Reactivity = 0
SECTION I 鈥? IDENTITY AND MANUFACTURER'S INFORMATION (521N-100A)
Manufacturer's Name: HILLYARD INDUSTRIES Product Name: COVER 2 (Part A & B mixed)
Address: 302 North Fourth Street Date Prepared: September 15, 2004
St. Joseph, MO 64501 Prepared by: Regulatory Affairs Department
Emergency Telephone No.: (800) 424-9300 (Only in the event of chemical emergency involving a spill, leak, fire,
exposure or accident involving chemicals.) Other information calls: (816) 233-1321 (Ext. 8285)
SECTION II 鈥? INGREDIENTS/IDENTITY INFORMATION
Components
(Specific Chemical Identity: OTHER LIMITS
Common Name(s) CAS # OSHA PEL ACGIH TLV RECOMMENDED %
Water 7732-18-5 none none N.A. ---
Styrene Acrylic Copolymer Unknown to not established not established N.A. ---
Emulsion Hillyard
1-Phenoxy-2-Propanol 770-35-4 not established not established N.A. ---
Volatile Organic Compounds = 170 grams per liter/less water / Volatile Organic Substances = 0.4 pounds per gallon
SECTION III 鈥? PHYSICAL / CHEMICAL CHARACTERISTICS
Specific Gravity (HB2O = 1): 25潞C = 1.03 39潞C = 1.03
Boiling Point: 214掳F B
Vapor Pressure (mm Hg.): 18.8 74.1
Percent Volatile by Volume (%):
Vapor Density (AIR = 1): 0.62 Evaporation Rate (ethyl ether = 1): slower than 1
complete Appearance and Odor: Milky white liquid; non-objectionable odor
Solubility in Water:
pH = 9.2
SECTION IV 鈥? FIRE AND EXPLOSION HAZARD DATA
None to 200潞F (T.C.C.) Flammable Limits: LEL = N.A. UEL = N/A
Flash point:
Extinguishing Media: Water fog, foam, carbon dioxide, dry chemical, halogenated agents.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus with full facepiece and protective
clothing.
Unusual Fire and Explosion Hazards: None known to manufacturer
SECTION V 鈥? PHYSICAL HAZARDS
Stability: Stable Conditions to Avoid: Elevated temperatures
Incompatibility (Materials to Avoid): None known to manufacturer.
Hazardous Decomposition Products or Byproducts: When exposed to fire, produces smoke, soot, carbon
monoxide and carbon dioxide.
Hazardous Polymerization: Will not occur Conditions to Avoid: None known to Hillyard
SECTION VI 鈥? HEALTH HAZARD DATA
Routes of entry: Inhalation? Yes Skin? Yes Ingestion? Yes
HEALTH HAZARDS (1. Acute and 2. Chronic)
1. Prolonged contact may cause skin irritation. Excessive exposure to vapors or spray mist can cause irritation of
the nose and throat. Not acutely toxic when administered orally at a dose level of 5.0 g./kg.; however, ingestion
may be harmful and cause irritation of the digestive tract. Inhalation - Not expected to be acutely toxic.
2. None known to Hillyard.
Chemical listed as Carcinogen or Potential Carcinogen:
National Toxicology Program = No I.A.R.C. Monographs = No OSHA = No
This product has no carcinogens listed by IARC, NTP, NIOSH, or ACGIH as of this date, greater than or equal
to 0.1%.
Signs and Symptoms of Exposure: Prolonged skin contact may cause irritation. Excess inhalation may irritate
nose and throat. Ingestion may cause gastrointestinal irritation.
page 2 of #496 鈥? Cover 2 (Part A & B mixed)
SECTION VI 鈥? HEALTH HAZARD DATA continued
Medical Conditions Generally Aggravated by Exposure: None known to manufacturer.
Emergency and First Aid Procedures: In case of eye contact, immediately flush with plenty of water for at least 15
minutes. If redness, itching, or a burning sensation develops, have eyes examined and treated by medical personnel. In
case of skin contact, immediately flush skin with plenty of water for 15 minutes. If redness, itching, or burning sensation
develops, get medical attention. Wash contaminated clothing and decontaminate footwear before reuse. Ingestion: DO
NOT INDUCE VOMITING. Give one or more glasses of water to drink and refer to medical personnel, physician, or
poison control center. Never give anything by mouth to an unconscious person. Inhalation: Remove victim to fresh air.
If a cough or other respiratory symptoms develop, consult medical personnel.
SECTION VII 鈥? PRECAUTIONS FOR SAFE HANDLING AND USE
Steps To Be Taken In Case Material Is Released Or Spilled: Avoid breathing vapors. Ventilate area. Contain and
remove with inert absorbent and non-sparking tools.
Waste Disposal Method: Dispose of in accordance with state and federal regulations. Do not incinerate closed
container.
Precautions To Be Taken In Handling And Storing: Do not store above 100潞F. Keep containers closed when not in
use and upright to prevent leakage. Store in cool, well-ventilated area away from heat and out of direct sunlight. Protect
from freezing.
Other Precautions: Do not take internally. USE WITH ADEQUATE VENTILATION. Avoid breathing vapors or
spray mist. Open windows and doors, use exhaust fans or other means to insure fresh air entry during application and
drying. Avoid prolonged or repeated contact with skin. Refer to OSHA Standard 29 CFR 1910.94 for technical
guidelines on keeping air contamination below acceptable exposure limits.
SECTION VIII 鈥? CONTROL MEASURES
Respiratory Protection (Specify Type): None normally required when used according to label directions. Avoid
breathing spray mist. If sprayed, wear mechanical filter respirator to remove solid particles of overspray. Provide general
clean air dilution per good engineering practices.
Ventilation:
Local Exhaust = Not required Mechanical (General) = Recommended Special = N/A Other = N/A
with normal use
Protective Gloves: vinyl gloves if unable to avoid skin contact Eye Protection: Not necessary with normal use
Other Protective Clothing or Equipment: None normally required. If unable to avoid prolonged or repeated contact
with skin, wear impervious clothing.
Work / Hygienic Practices: Wash thoroughly after handling. Upon contact, remove contaminated clothing and shoes;
wash before reuse (including shoes).
SECTION IX 鈥? TRANSPORTATION INFORMATION
Applicable regulations: 49 CFR = No IMCO = No IATA = No
Proper shipping name: Varnish
UN No.: Not applicable Limited Qty.: Not applicable Hazard Class: Not applicable.
Labels required: Not required DOT Exception: Not applicable
EPA Hazardous waste number / code: Not listed
Hazardous waste characteristics:
Ignitability = Not applicable Corrosivity = Not applicable Reactivity = Not applicable
DISCLAIMER OF WARRANTIES
NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR OF ANY NATURE ARE MADE WITH RESPECT TO THE PRODUCT(S) OR INFORMATION
CONTAINED IN THIS MATERIAL SAFETY DATA SHEET.
The information and recommendations contained in this Material Safety Data Sheet are supplied pursuant to 29 CFR 1910.1200 of the
Occupational Safety and Health Standards Hazard Communication Rule. All information contained herein is presented in good faith and
is believed to be appropriate and accurate.
THE BUYER OR USER ASSUMES ALL RISKS ASSOCIATED WITH THE USE, MISUSE OR DISPOSAL OF THIS PRODUCT. THE
BUYER OR USER IS RESPONSIBLE TO COMPLY WITH ALL FEDERAL, STATE OR LOCAL REGULATIONS CONCERNING
THE USE, MISUSE OR DISPOSAL OF THESE PRODUCTS.
|