Krystol Plug
Material Safety Data Sheet
May 2008
Section I 鈥? Product Identification
This MSDS covers all products listed
Product Code: K-315, K-510, K-511, K-520, K-620, K-630
Product Name: Krystol Bari-cote; Krystol Grout 500; Krystol Plasti-patch; Krystol Grout 700; Krystol
Plug; Krystol Poly Top Mortar; Kryton Patching Mortar.
Note: This MSDS covers each of the above named products.
Intended Use: Concrete Patch/Repair
WHMIS: D2b (materials causing other toxic effects: skin or eye irritant)
Section II 鈥? Hazardous Ingredients
Ingredient: % by weight CAS# Exposure Limits
ACGIH TLV - TWA
0.5 mg respirable dust / m3
Silica, crystalline, quartz 15-40 14808-60-7
10 mg total dust / m3
Portland cement 15-40 65997-15-1
Section III 鈥? Physical Data
Colour: Grey
Appearance: Powder
Physical State: Solid
Odour: Odourless
Vapour Density: Not applicable
(compared to air=1)
Soluble in Water: 5-15%
Boiling Point: N/D
Specific Gravity: 1.3
pH: Not available
Section IV 鈥? Fire and Explosion Data
Flammable (Y/N): No
Flash Point and Method: Not applicable
Hazardous Combustion None
Products:
Firefighting Measures: Use methods for surrounding fire; material will not burn.
Page 2 of 2
MSDS: Krystol Plug
Section V 鈥? Reactivity Data
Chemical Stability: Stable
Incompatibility with other Mixture with strong acids and bases will cause rapid decomposition which may
substances: release CO or CO2
Reactivity: Becomes caustic when mixed with water
Hazardous Decomposition None
Products:
Section VI 鈥? Health Hazard Data
Route(s) of Exposure: Eyes, skin, inhalation, ingestion
Exposure Limits: TWA 10 mg per cubic meter of airborne dust
Acute Exposure Effects: Contact with eyes will cause severe irritation; wet material may cause irritation of
the skin; inhalation of dust may cause respiratory tract irritation
Chronic Exposure Effects: Prolonged inhalation of silica dust has been known to result in silicosis. Prolonged
or repeated exposure of wet material to the skin may cause chemical burns.
Mutagenicity: No data
Carcinogenicity: No data
Irritancy: Moderate
Sensitization: N/D
Section VII 鈥? Preventative Measures
Protective Clothing to be Wear protective goggles, long sleeves and rubber gloves
Worn:
Respirator: Dry material may produce airborne dust which may require a dust mask.
Ventilation: Adequate ventilation must be provided for all enclosed work spaces.
Storage: Store in the original sealed container.
Spill Procedures: Replace in the original sealable container
Disposal Procedures: Dispose of in accordance with local regulations.
Section VIII 鈥? First Aid Measures
Skin contact: Flush with large amounts or clean water, use non-abrasive soap if available. Remove
any contaminated clothing. If irritation persists, seek medical attention.
Eye Contact: Remove any contact lenses. Flush with large amounts of clean water for 15 minutes.
If irritation persists, seek medical attention.
Inhalation: Immediately move victim to fresh air.
Ingestion: Do not induce vomiting. Guard against aspiration into lungs. Get prompt medical
attention. Material is not toxic. If victim is conscious and alert, give two glasses of
water.
In case of a dangerous goods emergency, call: (613) 996-6666
Prepared by: Dept. Group #7, Contect Testing, May 29, 1995
Reviewed and/or Revised Kryton International Inc., May 2008
by:
|