MATERIAL SAFETY DATA SHEET
Revised/ Reviewed: July 25, 2007
INSTRUMENT LUBRICANT REF 3-705
A lubricant for hand-held surgical instruments.
Section 1- Product and Company Information
Manufactured for: Miltex, Inc; 589 Davies Drive, York, PA 17402
Information: 717-840-9335, 717-840-9347 (fax)
Chemical Name & Synonyms: --
Chemical Formula: --
Section 2 鈥? Composition/ Information on Ingredients
No hazardous ingredients. All ingredients in this product are on the TSCA list. This product does not
contain an amount of any chemical required to be reported under SARA 313.
Section 3 - Health Identification
No inhalation hazard expected under normal conditions of use. Prolonged inhalation of mist may
cause irritation of the respiratory tracts, difficulty breathing, lightheadedness, drowsiness, and
headache. Eye contact may cause slight irritation in the form of discomfort, excess blinking and tear
production, and redness. Prolonged or repeated skin contact may cause slight irritation and redness.
Ingestion may cause stomach distress, headache, and dizziness. Accidental swallowing of large doses
may result in nausea, vomiting, diarrhea, and weakness.
Primary Route(s) of Entry: Skin and ingestion.
Carcinogen: ARC Program- No IARC Program- No OSHA Program- No
Medical Conditions Aggravated by Exposure: Pre-existing skin disorders may be aggravated.
Section 4 - First Aid Measures
Eyes: Flush with tepid water for at least 15 minutes. If irritation persists, immediately seek medical
attention.
Skin: Wash with soap and water. If irritation persists, seek medical attention.
Ingestion: Rinse mouth and throat with water. Drink 1-2 glasses of water. Do not induce vomiting.
Immediately get medical attention.
Inhalation: Remove person to fresh air. If person is having difficultly breathing, give oxygen and
immediately call a physician.
Section 5 鈥? Fire Fighting Measures
Flash Point (Test Method): >200掳F (200掳C) (method unknown)
Auto Ignition Temperature: unknown
Flammable Limits- LEL: not established UEL: not established
Extinguishing Media: Foam, dry chemical powder, and carbon dioxide.
Special Fire Fighting Procedures: None.
Unusual Fire and Explosion Hazards: None.
Page 1 of 2 Instrument Lube (Milk) MSDS
Section 6 - Physical and Chemical Properties
Physical State: Milky white liquid. No odor.
Appearance and Odor: Clear with an odor characteristic to mineral oil.
Boiling Point (掳C): Not determined
Specific Gravity (H2O=1): 0.98 Vapor Density (Air=1): Not determined
3
Density: 850 kg/m @ 59掳F (15掳C) Solubility in Water: Partial
Vapor Pressure (mm Hg): Not determined pH: 6.5
Evaporation Rate (Butyl Acetate=1): Not applicable
Section 7 鈥? Stability and Reactivity
Stability: Stable
Conditions to Avoid: None.
Incompatibility/ Materials to Avoid: Strong oxidizing agents
Hazardous Decomposition Products: May include and are not limited to oxides of carbon, aldehydes,
and ketones.
Hazardous Polymerization: Will not occur.
Section 8 鈥? Accidental Release, Disposal, and Ecological Information
Spill Response: Absorb spill with an absorbent material and place in container for disposal. Wash the
contaminated area with soap and water.
Waste Disposal Method: Dispose of in accordance with all applicable federal, state, and local
regulations.
Ecological, General: --
Section 9 鈥? Exposure Controls/ Personal Protection
Eye Protection: Safety glasses.
Respiratory Protection: Not normally required.
Ventilation Recommendations: General ventilation normally adequate.
Skin Protection: Latex, rubber, nitrile, or polyethylene gloves recommended for prolonged contact.
Other: None.
Section 10 鈥? Storage and Handling
Storage: Store in a cool, dry area. Keep out of reach of children.
Handling: Read and follow label instructions.
Section 11 鈥? Miscellaneous
Toxicological Information: --
Transportation Information: Not a DOT hazardous material.
Other: --
Liability Disclaimer: MSDS information is provided based on OSHA鈥檚 Hazardous Communication Regulation and for use of the persons
required to receive this information under this regulation. The information is neither designed nor recommended for any other use or for
use by any other person, including compliance with other laws. Miltex does not warrant the suitability for use of this MSDS for any
other material or product not specifically identified herein. Miltex does not warrant the accuracy or authenticity of this MSDS unless it
has been obtained directly from Miltex, or posted or viewed on a Miltex website. This MSDS is based on information that is believed to
be reliable, but may be subject to change as new information becomes available. Because it is not possible to anticipate all conditions of
use, additional safety precautions may be required. Since the use of this material is not under Miltex鈥檚 control, each user is responsible
for making their own determination as to the safe and proper handling of this material in their own particular use of this material. Miltex
makes no representation or warranty, either express or implied, including as to merchantability or fitness for a particular purpose.
Page 2 of 2 Instrument Lube (Milk) MSDS
|