MATERIAL SAFETY DATA SHEET
Revised/ Reviewed: July 23, 2007
SLIDE鈩?
An endodontic file lubricant to facilitate file movement within and debris removal from the root canal.
Section 1- Product and Company Information
Manufactured by: Miltex, Inc.; 589 Davies Drive, York, PA 17402
Information: 717-840-9335, 717-840-9347 (fax)
Chemical Name & Synonyms: 1,2,3-Propanetriol/ Urea peroxide/ Polyethylene glycol
Chemical Formula: Product is a mixture
Section 2 鈥? Composition/ Information on Ingredients
Glycerin; CAS # 56-81-5; < 90% w/v; ACGIH TLV = 10 mg/m3
Urea Peroxide; CAS # 124-43-6; < 10% w/v; no information on threshold limit
Polyethylene Glycol 200; CAS # 25322-68-3; < 5% w/v; no information on threshold limit
Section 3 - Health Identification
Potential Health Effects: Inhalation of mist or spray can cause respiratory distress. Allergic reaction
possible from prolonged contact.
Primary Route(s) of Entry: Ingestion, Inhalation, and Skin Contact
Carcinogen: No information available. None of the material鈥檚 components are carcinogenic.
Medical Conditions Aggravated by Exposure: No information available
HMIS Ratings: Health = 2; Flammability = 1; Reactivity = 0; PPE = B
Section 4 - First Aid Measures
Eyes: Flush with water for at least 15 minutes. Seek immediate medical attention.
Skin: Remove any contaminated clothing. Wash affected area with soap and water.
Ingestion: Not likely to be a hazard when used as directed. Seek medical attention should
complications develop.
Inhalation: Not likely to be a hazard when used as directed. Remove person to fresh air.
Section 5 鈥? Fire Fighting Measures
Flash Point (Test Method): 320掳F (closed-cup)
Auto Ignition Temperature: No information available
Flammable Limits- No information available
Extinguishing Media: Use suitable for surrounding materials.
Special Fire Fighting Procedures: If necessary, wear self-contained breathing apparatus and protective
clothing.
Unusual Fire and Explosion Hazards: Hazardous when exposed to flames, heat, or oxidizers.
Page 1 of 2, Slide MSDS
Section 6 - Physical and Chemical Properties
Physical State: Liquid pH: No information available
Appearance and Odor: A clear, colorless, viscous liquid.
Melting Point (掳C): Not applicable Solubility in Water: Soluble
Specific Gravity (H2O=1): No information available; likely greater than 1.
Vapor Pressure (mm Hg): No information available
Vapor Density (Air=1): No information available
Evaporation Rate (butyl acetate=1): No information available
Section 7 鈥? Stability and Reactivity
Stability: No information available, thought to be stable.
Conditions to Avoid: Heat and open flame
Incompatibility/ Materials to Avoid: Contact with strong oxidizing agents may cause explosion.
Hazardous Polymerization: No information available, believed that it will not occur.
Hazardous Decomposition Products: Carbon oxides and acrolein
Section 8 鈥? Accidental Release, Disposal, and Ecological Information
Spill Response: Absorb with sand or vermiculite, scoop up and containerize for proper disposal.
Waste Disposal Method: Dispose of in accordance with all applicable federal, state, and local
regulations.
Ecological, General: No information available
Section 9 鈥? Exposure Controls/ Personal Protection
Eye Protection: Safety glasses or goggles
Respiratory Protection: Wear self-contained breathing apparatus in high vapor areas.
Ventilation Recommendations: Provide adequate general and local exhaust ventilation.
Skin Protection: Impervious gloves
Other: As required to prevent skin, eye, and clothing contact. Do not breathe vapors.
Section 10 鈥? Storage and Handling
Storage: Store in a cool, dry, well-ventilated area. Keep container tightly-closed.
Handling: Wash thoroughly after handling. Keep away from acids, oxidizers, and ignition sources.
Section 11 鈥? Miscellaneous
Toxicological Information: Glycerin LD50 (oral, rat) = 12,600 mg/kg; Polyethylene Glycol 200 LD50
(oral, rat) = 28 gm/kg
Transportation Information: Material is not a U.S. DOT Hazardous Material
Other: --
Liability Disclaimer: MSDS information is provided based on OSHA鈥檚 Hazardous Communication Regulation and for use of the persons
required to receive this information under this regulation. The information is neither designed nor recommended for any other use or for
use by any other person, including compliance with other laws. Miltex does not warrant the suitability for use of this MSDS for any
other material or product not specifically identified herein. Miltex does not warrant the accuracy or authenticity of this MSDS unless it
has been obtained directly from Miltex or posted or viewed on a Miltex website. This MSDS is based on information that is believed to
be reliable, but may be subject to change as new information becomes available. Because it is not possible to anticipate all conditions of
use, additional safety precautions may be required. Since the use of this material is not under Miltex鈥檚 control, each user is responsible
for making their own determination as to the safe and proper handling of this material in their own particular use of this material. Miltex
makes no representation or warranty, either express or implied, including as to merchantability or fitness for a particular purpose.
Page 2 of 2, Slide MSDS
|