MATERIAL SAFETY DATA SHEET
Revised/ Reviewed: February 20, 2007
Prophy and Handpiece Lube
A lubricant for dental handpieces and prophy angles.
Section 1- Product and Company Information
Manufacturer: Miltex, Inc; 589 Davies Drive, York, PA 17402
Information: 717-840-9335, 717-840-9347 (fax)
Chemical Name & Synonyms: Mineral oil
Chemical Formula: --
Section 2 鈥? Composition/ Information on Ingredients
No hazardous ingredients. The product is a blend of highly-refined mineral oils.
Section 3 - Health Identification
Not considered a health hazard under normal conditions of use. Contains mineral oil for which
exposure limits for oil mist apply. Prolonged and/or frequent exposure can result in de-fatting of the
skin, particularly at elevated temperatures. This can lead to irritation and possibly dermatitis,
especially under conditions of poor personal hygiene.
Primary Route(s) of Entry: Inhalation and ingestion.
Carcinogen: ARC Program- No IARC Program- No OSHA Program- No
Medical Conditions Aggravated by Exposure: None known.
Section 4 - First Aid Measures
Not expect to give rise to an acute hazard under normal conditions of use. Treat symptomatically.
Eyes: Flush with tepid water for at least 15 minutes. If persistent irritation occurs, seek medical
attention.
Skin: Remove contaminated clothing and wash affected area with soap and water. If persistent
irritation occurs, obtain medical attention.
Ingestion: Do not induce vomiting. Wash out mouth with water and seek medical attention.
Inhalation: In the event of dizziness or nausea, remove person to fresh air. If symptoms persist, seek
medical attention.
Page 1 of 3 Prophy/Handpiece Lube MSDS
Section 5 鈥? Fire Fighting Measures
Flash Point (Test Method): 392掳F (200掳C) (method unknown)
Auto Ignition Temperature: >608掳F (320掳C) (typical)
Flammable Limits- LEL: 1% V/V (typical) UEL: 10% V/V (typical)
Extinguishing Media: Foam and dry chemical powder. Carbon dioxide, sand, or earth may be used for
small fires only.
Special Fire Fighting Procedures: DO NOT use a water jet as an extinguishing media.
Unusual Fire and Explosion Hazards: Not classified as flammable, but will burn. Combustion is likely
to give rise to a complex mixture of airborne solid and liquid particulates and gases, including carbon
monoxide, oxides or sulfur, and unidentified organic and inorganic compounds.
Section 6 - Physical and Chemical Properties
Physical State: Liquid at ambient temperature.
Appearance and Odor: Clear with an odor characteristic to mineral oil.
Boiling Point (掳C): >280 (536掳F)
Density: 850 kg/m3 @ 59掳F (15掳C)
Vapor Pressure: <0.5 pascals at 68掳F (20掳C)
Vapor Density (Air=1): >1 at 68掳F (20掳C)
Solubility in Water: Poorly soluble
Section 7 鈥? Stability and Reactivity
Stability: Stable
Conditions to Avoid: Extremes of temperature and direct sunlight
Incompatibility/ Materials to Avoid: Strong oxidizing agents
Hazardous Decomposition Products: None expected to form during normal storage.
Section 8 鈥? Accidental Release, Disposal, and Ecological Information
Spill Response: Avoid contact with skin and eyes. Wear impermeable gloves and boots. Absorb
liquid with sand or earth. Prevent from spreading or entering into drains, ditches, or waterways.
Waste Disposal Method: Dispose of in accordance with all applicable federal, state, and local
regulations.
Ecological, General: Liquid under most environmental conditions. Product floats on water. If it enters
soil, it will adhere to soil particles and will not be mobile. Major constituents are expected to be
inherently biodegradable, but the product contains components that may persist in the environment.
Product has the potential to bio-accumulate.
Section 9 鈥? Exposure Controls/ Personal Protection
Eye Protection: Wear safety glasses or full-face shield if splashes are likely to occur.
Respiratory Protection: Not normally required
Ventilation Recommendations: Use local exhaust if a risk of inhalation of vapors, mist, or aerosols
exists.
Skin Protection: PVC or nitrile gloves are recommended
Other: Wash hands before eating, drinking, smoking, and going to the toilet.
Page 2 of 3 Prophy/Handpiece Lube MSDS
Section 10 鈥? Storage and Handling
Storage: Keep in a cool, dry, well-ventilated place. Use properly labeled and closeable containers.
Avoid direct sunlight, heat sources, and strong oxidizing agents. Store between 32掳F (0掳C) and 122掳F
(50掳C).
Handling: Avoid making product into a mist or aerosol and then breathing it in.
Section 11 鈥? Miscellaneous
Toxicological Information: Acute toxicity (oral) = LD50 expected to be 2,000-mg/kg
Acute toxicity (dermal) = LD50 expected to be 2,000-mg/kg
Eye irritant = expected to be a slight irritant
Skin irritant = expected to be a slight irritant
Respiratory irritant = If mists inhaled, slight irritation of the respirator
track may occur.
Skin sensitization = Not expected to be a skin sensitizer
Mutagenicity = Not considered to be a mutagenic agent
Transportation Information: Not a DOT hazardous material.
Other: Not classified as dangerous under EC Directive 88/379/EEC or U.S. EPA Recovery Act
Liability Disclaimer: MSDS information is provided based on OSHA鈥檚 Hazardous Communication Regulation and for use of the persons
required to receive this information under this regulation. The information is neither designed nor recommended for any other use or for
use by any other person, including compliance with other laws. Miltex does not warrant the suitability for use of this MSDS for any
other material or product not specifically identified herein. Miltex does not warrant the accuracy or authenticity of this MSDS unless it
has been obtained directly from Miltex, or posted or viewed on a Miltex website. This MSDS is based on information that is believed to
be reliable, but may be subject to change as new information becomes available. Because it is not possible to anticipate all conditions of
use, additional safety precautions may be required. Since the use of this material is not under Miltex鈥檚 control, each user is responsible
for making their own determination as to the safe and proper handling of this material in their own particular use of this material. Miltex
makes no representation or warranty, either express or implied, including as to merchantability or fitness for a particular purpose.
Page 3 of 3 Prophy/Handpiece Lube MSDS
|