MATERIAL SAFETY DATA SHEET
Revised/ Reviewed: July 23, 2007
SLIDE鈩? SH (a.k.a. Slide鈩? SH Juniors)
An endodontic file lubricant to facilitate file movement within and debris removal from the root canal.
Section 1- Product and Company Information
Manufactured by: Miltex, Inc.; 589 Davies Drive, York, PA 17402
Information: 717-840-9335, 717-840-9347 (fax)
Chemical Name & Synonyms: 1,2,3-Propanetriol/ Sodium Hypochlorite
Chemical Formula: Poly alcohols/ Bleach/ Water
Section 2 鈥? Composition/ Information on Ingredients
Glycerin; CAS # 56-81-5; < 80% w/v; ACGIH TLV = 10 mg/m3
Sodium Hypochlorite; CAS # 7681-52-9; < 0.1% w/v; no information on threshold limit
The balance is material is water.
Section 3 - Health Identification
Potential Health Effects: Inhalation of mist or spray can cause respiratory distress. Allergic reaction possible
from prolonged contact.
Primary Route(s) of Entry: Ingestion, Inhalation, and Skin Contact
Carcinogen: None of the materials components are known to be carcinogenic.
Medical Conditions Aggravated by Exposure: No information available
HMIS Ratings: Health = 1; Flammability = 1; Reactivity = 0; PPE = B
Section 4 - First Aid Measures
Seek medical attention for all cases of overexposure.
Eyes: Flush with tepid water for at least 15 minutes. Seek medical attention.
Skin: Remove any contaminated clothing. Wash affected area with soap and water.
Ingestion: Seek medical attention should complications develop.
Inhalation: Remove person to fresh air. As needed, seek medical attention.
Section 5 鈥? Fire Fighting Measures
Flash Point (Test Method): 320掳F (closed-cup)
Auto Ignition Temperature: No information available Flammable Limits- No information available
Extinguishing Media: Use suitable for surrounding materials.
Special Fire Fighting Procedures: If necessary, wear self-contained breathing apparatus and protective
clothing.
Unusual Fire and Explosion Hazards: Hazardous when exposed to flames, heat, or oxidizers.
Page 1 of 2, Slide SH MSDS
Section 6 - Physical and Chemical Properties
Physical State: Liquid at ambient temperature.
Appearance and Odor: A clear, colorless, viscous, gel-like liquid.
Melting Point (掳C): Not applicable
Specific Gravity (H2O=1): No information available, likely greater than 1.
Vapor Pressure (mm Hg): No information available Vapor Density (Air=1): No information available
Evaporation Rate (butyl acetate=1): No information available
Solubility in Water: Soluble pH: No information available
Section 7 鈥? Stability and Reactivity
Stability: No information available, thought to be stable.
Conditions to Avoid: Heat and open flame
Incompatibility/ Materials to Avoid: Contact with strong oxidizing agents may cause explosion.
Hazardous Polymerization: No information available, believed that it would not occur.
Hazardous Decomposition Products: Carbon oxides and acrolein
Section 8 鈥? Accidental Release, Disposal, and Ecological Information
Spill Response: Absorb with sand or vermiculite, scoop up and containerize for proper disposal.
Waste Disposal Method: Dispose of in accordance with all applicable federal, state, and local regulations.
Ecological, General: No information available
Section 9 鈥? Exposure Controls/ Personal Protection
Eye Protection: Safety glasses or goggles
Respiratory Protection: None normally required. Wear self-contained breathing apparatus in high vapor
areas.
Ventilation Recommendations: Local and general as needed.
Skin Protection: Impervious gloves
Other: As required to keep materials from eyes, skin, or clothing and from inhaling vapors.
Section 10 鈥? Storage and Handling
Storage: Store in a cool, dry, well-ventilated area. Keep container tightly closed. Keep away from oxidizers,
acids, and ignition sources.
Handling: Wash thoroughly after handling.
Section 11 鈥? Miscellaneous
Toxicological Information: Glycerin LD50 (oral, rat) = 12,600 mg/kg
Transportation Information: Material is not a U.S. DOT Hazardous Material
Other: --
Liability Disclaimer: MSDS information is provided based on OSHA鈥檚 Hazardous Communication Regulation and for use of the persons
required to receive this information under this regulation. The information is neither designed nor recommended for any other use or for use by
any other person, including compliance with other laws. Miltex does not warrant the suitability for use of this MSDS for any other material or
product not specifically identified herein. Miltex does not warrant the accuracy or authenticity of this MSDS unless it has been obtained directly
from Miltex or posted or viewed on a Miltex website. This MSDS is based on information that is believed to be reliable, but may be subject to
change as new information becomes available. Because it is not possible to anticipate all conditions of use, additional safety precautions may be
required. Since the use of this material is not under Miltex鈥檚 control, each user is responsible for making their own determination as to the safe
and proper handling of this material in their own particular use of this material. Miltex makes no representation or warranty, either express or
implied, including as to merchantability or fitness for a particular purpose.
Page 2 of 2, Slide SH MSDS
|