Bonstone Materials Corporation Page 1 of 2
1. Product Nam e 5. Installation 6. Availability
Boncrete鈩? 414 General Instructions Packaging and Storage
(If using cartridges, additional Boncrete鈩? 414 is available in
2. Manufacturer
usage directions are available. See quarts, gallons, 5 gallon pails,
our information sheet labeled and 55 gallon drums, and also
Bonstone Materials Corporation "Cartridge use directions".) CSI in 300ml cartridges. Shelf life is
format specifications are available. approximately one year if kept
in unopened containers in a dry
3. Product Description
area at 75 掳F. If BONCRETE鈩?
Surface Preparation and Use
414 Part A is exposed to
A two -component, exterior grade, gray, self- below room te mperature
le veling epoxy. Use gloves, wear eye protection, conditions for extended
and avoid skin contact. When periods of time, it may
grinding cured joints, wear a dust
Basic Uses crystallize, giving it a stiff,
mask. Substrate to be bonded must grainy consistency. The
be completely dry and dust-free. product must be
Stone or concrete crack injection, Mix only the amount of epoxy, reconstituted before use by
patching and mending which can be used in 10 minutes. heating it to 150 掳F degrees.
Avoid stressing joint before
Self-le veling flooring Stir until it becomes a
complete cure of epoxy. Mask homogeneous liquid.
Self-le veling machinery grout areas, which must be kept free of
Pick-proof sealant/adhesive epoxy. Clean uncured epoxy from
7. Warranty
tools with toluene or xylene.
Bonding stone or hardened concrete to
Remove cured epoxy mechanically.
hardened concrete
This warranty is limited to
Anchor bolt adhesive
re placement of defective
Mix ing Ins truc tions
Bonding stone to other construction material and freight charges to
materials destination only. Bonstone
All ma terials should be at or above Materials Corp. is not
General purpose adhesive for wood,
55掳F. Co mbine the two ingredients re sponsible for consequential
concrete, metal
at the following volume ratio: one damages.
part Boncrete鈩? 414 Part A to one
part Boncrete鈩? 414 Part B. Mix
8. Maintenance
Lim itations thoroughly--- in gredients must be
blended homogeneously for proper
cure.
Use on stone free of oil, grease, wax, coatings Designed for application in
and other contaminates. areas inaccessible to
maintenance procedures.
Temperature Dependency
4. Technical Data
Temperature will affect the working 9. Technical Service
properties of the material.
Cured Properties Approximately every 15掳F re sults in
Specification Service
doubling the speed of cure.
1 part 414 Pa rt A, to 1 part 414
Mix ratio
Therefore, at 90掳F set time is cut in
Part B b y volume
half, at 60 掳F the set time is Specifications for
Pot life
10 minutes doubled. Do not use on a substrate various applications
@ 75 掳F
at a temperature below 55 掳
Specification writing
Mix ed Properties F.Temp erature will affect the
dept. for unique
working properties of the material.
Init ial Set T ime applications
2 hours Approximately every 15掳F re sults in
@ 75 掳F
doubling the speed of cure.
Full cu re time @ 75 掳F: Within 24 hours
Therefore, at 90掳F set time is cut in
half, at 60 掳F the set time is
Test
Pro p erty Value
doubled. Do not use on a substrate
Meth o ds
at a temperature below 55 掳F.
Tensile Stre ngth 4816 p si ASTM D -638
Tensile Modu lus 37000 psi ASTM D -638
Cov erage
Tensile Elo ngation 0.105 ASTM D -638
Comp ressive Strengt h 29000 psi ASTM D -695 Approximately 30 square feet per
gallon when applied at 50 mils
154000
Comp ressive M odulus ASTM D -695
(1 /16th of an inch). 231 cubic
psi
in ches per gallon.
Flexura l Strength 29000 psi ASTM D -790
375000
Flexura l M odulus ASTM D -790
psi
ASTM D -
Shore D H ardn ess 89
2240
Heat D isto rtion
132掳C ASTM D -648
Tem pera ture
Thi s i nfo rm a tio n i s fu rn is he d w ith o ut w a rra n ty, re pr es e nta tio n , in d uc em e n t, o r l ice n se o f a n y k in d , e x ce pt th a t i s is
ac cu ra te to the b e st of B on s to n e Ma te ria l C o rp o ra tio n 's ( BM C ) kn o wl e dg e o r ob ta in e d fr om so u rce s b e li e ve d b y B MC to
be a ccu ra te , an d BM C do e s n o t a ss u me a ny le g al re sp o ns ib il ity fo r u se o f re li an ce u p on sa m e . U s er m u st d ete rm in e if
th e p ro du ct, p ro ce ss , o r i n fo rm a tio n de sc ri be d is s u ita bl e to th e i n te n d ed a p pl ic a ti o n. B efo re u si ng a ny ch e mi ca l, re a d i ts
la b el an d Ma te ri al Sa fe ty D ata Sh e e t.
Bonstone庐 Materials Corporation
http://www.bonstone.com/tds/technical data.asp 3/4/2004
Bonstone Materials Corporation Page 2 of 2
707 Swan Drive 鈥? Mukwonago, WI 53149
Local (262) 363-9877 鈥? Toll-Free (800) 425-2214
Fax (262) 363-9879 鈥? Email general@ bons tone.com
漏 1999-2002 Bonstone Materials Corporation.
http://www.bonstone.com/tds/technical data.asp 3/4/2004
|