Bonstone Materials Corporation Page 1 of 2
1. Product Nam e 5. Installation 6. Availability
Bonstone庐 Match Family (A-101-T/B -431) General Instructions Packaging and Storage
(S ee separate doweling, Bonstone庐 A-101-T a nd B -431
2. Manufacturer
la minating, and patching are available in quarts, gallons,
in structions for more specific and 5 gallon pails. Shelf life is
Bonstone Materials Corporation in structions. CSI format approximately one year if kept
specifications are available.) in unopened cans in a dry area
at 75掳F. **If BONSTONE鈩? A-
3. Product Description
101-T is exposed to below
Surface Preparation and Use
room te mperature conditions
A two -component exterior grade epoxy for extended periods of time,
adhesive, Thick paste. Thickening powders Use gloves, wear eye protection, it m ay crystallize, giving it a
available to make this product knifegrade and avoid skin contact. When stiff, grainy consistency. The
(Family Includes A-101-T, A -111-T, A-121-T, grinding cured joints, wear a dust product must be
A-131-T, A -181-T, A-191-T). mask. Substrate to be bonded must reconstituted before use by
be completely dry and dust-free. heating it to 150 掳F. Stir until it
Mix only the amount of epoxy
Basic Uses becomes a homogeneous
which can be used in 10 minutes. liquid.
Avoid stressing joint before
Patching and mending stone complete cure of epoxy. Mask
7. Warranty
areas which must be kept free of
Laminating stone to other construction
epoxy. Clean uncured epoxy from
materials
tools with toluol (toluene) or xylol This product鈥檚 warranty is
Bonding stone to stone
(xyle ne). (Use caution, these limite d to replacement of
Anchoring bolts in stone and concrete solvents are flammable. Ensure defective material and freight
lo cal ventilation.) Remove cured charges to destination only.
epoxy mechanically. Bonstone Materials Corp. is not
Lim itations
re sponsible for consequential
damages.
Mix ing Ins truc tions
Use on stone free of oil, grease, wax, coatings
and other contaminates. Some yellowing and
8. Maintenance
chalking will occur when exposed to ultra-violet All ma terials should be at or above
lig ht. 50掳F. Co mbine the two ingredients
at the following weight ratio: two Designed for application in
parts A -101-T to one part B-431.
Color areas inaccessible to
Mix th oroughly--- in gredients must maintenance procedures.
be blended homogeneously for
Cream, rust, buff(tan), gray, red, white. proper cure. Best to mix using
Custom colors available. 9. Technical Service
double mix method, see reverse
side.
Applicable Standards Specification Service
Temperature Dependency
Indiana Limestone Institute specification for Specifications on file
units preassembled with thermosetting resins. Temperature will affect the working
Development of
properties of the material.
proposed specifications
Approximately every 10掳F re sults in
4. Technical Data for special projects.
doubling the speed of cure.
Therefore, at 85掳F set time is cut in
half, at 65 掳F the set time is Lab Service
Cured Properties
doubled. Do not use on a substrate
2 parts Match Part A-101-T, to
Mix ratio with a temperature below 45掳F.
1 part Match B -431 by w eig ht
Spectrophotometric
color matching is
Mixed viscosity Cre amy Paste
Cov erage available.
Pot life
20 minutes
Sample patches can be
@ 75 掳F
Approximately 30 square feet per made on stone
Mix ed Properties gallon when applied at 50 mils forwarded to lab.
(1 /16th of an inch). 231 cubic
Init ial Set T ime
2 hours in ches per gallon.
@ 75 掳F
Full cu re time @ 75 掳F: Within 24 hours
Test
Pro p erty Value
Meth o ds
Tensile Stre ngth 3800 p si ASTM D -638
Tensile Modu lus 48050 psi ASTM D -638
Tensile Elo ngation 0.083 ASTM D -638
Comp ressive Strengt h 26000 psi ASTM D -695
164000
Comp ressive M odulus ASTM D -695
psi
Flexura l Strength 8300 p si ASTM D -790
420000
Flexura l M odulus ASTM D -790
psi
ASTM D -
Shore D H ardn ess 90
1706
Heat D isto rtion
130 掳F ASTM D -648
Tem pera ture
Water Absorption (24
0.0006 ASTM D -570
hours):
http://www.bonstone.com/tds/technical data.asp 3/4/2004
Bonstone Materials Corporation Page 2 of 2
Thi s i nfo rm a tio n i s fu rn is he d w ith o ut w a rra n ty, re pr es e nta tio n , in d uc em e n t, o r l ice n se o f a n y k in d , e x ce pt th a t i s i s
ac cu ra te to the b e st of B on s to n e Ma te ria l C o rp o ra tio n 's ( BM C ) kn o wl e dg e o r ob ta in e d fr om so u rce s b e li e ve d b y B MC to
be a ccu ra te , an d BM C do e s n o t a ss u me a ny le g al re sp o ns ib il ity fo r u se o f re li an ce u p on sa m e . U s er m u st d ete rm in e if
th e p ro du ct, p ro ce ss , o r i n fo rm a tio n de sc ri be d is s u ita bl e to th e i n te n d ed a p pl ic a ti o n. B efo re u si ng a ny ch e mi ca l, re a d i ts
la b el an d Ma te ri al Sa fe ty D ata Sh e e t.
Bonstone庐 Materials Corporation
707 Swan Drive 鈥? Mukwonago, WI 53149
Local (262) 363-9877 鈥? Toll-Free (800) 425-2214
Fax (262) 363-9879 鈥? Email general@ bons tone.com
漏 1999-2002 Bonstone Materials Corporation.
http://www.bonstone.com/tds/technical data.asp 3/4/2004
|