Bonstone Materials Corporation Page 1 of 2
1. Product Nam e 5. Installation 6. Availability
Bonstone庐 Anchor (A-100/B -412X) General Instructions Packaging and Storage
(S ee separate doweling,
Bonstone庐 A-100 and B-412X
2. Manufacturer
la minating, and patching
are available in quarts, gallons,
in structions for more specific
and 5 gallon pails. Shelf life is
Bonstone Materials Corporation in structions. CSI format
approximately one year if kept
specifications are available.)
in unopened cans in a dry area
at 75掳F. **If Bonstone A-100
3. Product Description
is exposed to below room
Surface Preparation and Use
te mperature conditions for
A two -component exterior grade epoxy extended periods of time, it
adhesive. Six hour initial cure. Flowing paste Use gloves, wear eye protection, may crystallize, giving it a
viscosity (Family includes A-100, A-110, A- and avoid skin contact. When stiff, grainy consistency. The
120, A-130, A-180, & A -190). grinding cured joints, wear a dust product must be reconsti-
mask. Substrate to be bonded must tuted before us e by heating it
be completely dry and dust free.
Basic Uses to 1 50掳F degrees. Stir until it
Mix only the amount of epoxy becomes a homogeneous
which can be used in 10 minutes. liquid.
Setting anchor bolts Avoid stressing joint before
Laminating stone to other construction complete cure of epoxy. Mask
7. Warranty
areas which must be kept free of
material
epoxy. Clean uncured epoxy from
Stone to stone bonding tools with toluol (toluene) or xylol This product鈥檚 warranty is
(xy-le ne). ( Use caution, these limite d to replacement of
Lim itations solvents are flammable. Ensure defective material and freight
lo cal ventilation.) Remove cured charges to destination only.
Use on stone free of oil, grease, wax, coatings epoxy mechanically. Bonstone Materials Corp. is not
re sponsible for consequential
and other contaminates. Some yellowing and
damages.
chalking will occur when exposed to ultra-violet Mix ing Ins truc tions
lig ht.
8. Maintenance
All ma terial should be at or above
Color 60掳F. Co mbine the two ingredients
at the following weight ra-tio: One Designed for application in
part of A-100 to one part B-412X. areas inaccessible to
Six standard colors. Custom color matching
Mix th oroughly--- in gredients must maintenance procedures
available.
be blended homogene -ously for
proper cure. Best to mix using
9. Technical Service
Applicable Standards double mix method. See reverse
side.
Indiana Limestone Institute specifications for Specification Service
units preassembled with ther -mosetting resin. Temperature Dependency
Specifications for many
4. Technical Data The adhesive, substrate, and applications
environment鈥檚 temperature will
Specification writing
affect the working properties of the
dept. for unique
Cured Properties ma -terial. Approximately every 10 掳
applications
F re sults in doubling the speed of
1 part Anchor Part A -100, to 1
cure. Therefore, at 85 掳F set time is
Mix ratio part Anch or Pa rt B -412X by
weight cut in half, at 65 掳F the set time is Lab Service
doubled. Do not use on sub- stra te
Mixed viscosity Cre amy Paste
at a temperature below 55 掳F.
Spectrophotometric
Pot life
35 minutes
@ 75 掳F color matching available
Cov erage
Mix ed Properties
Init ial Set T ime Approximately 30 square feet per
6 hours
@ 75 掳F gallon when applied at 50 mils
(1 /16th of an inch). One gallon
Full cu re time @ 75 掳F: Within 24 hours
equals 231 cubic inches.
Test
Pro p erty Value
Meth o ds
Tensile Stre ngth 2464 p si ASTM D -638
Tensile Modu lus 74000 psi ASTM D -638
Tensile Elo ngation 0.038 ASTM D -638
Comp ressive Strengt h 61000 psi ASTM D -695
Comp ressive M odulus 67000 psi ASTM D -695
Flexura l Strength 5168 p si ASTM D -790
541000
Flexura l M odulus ASTM D -790
psi
ASTM D -
Shore D H ardn ess 91
1706
Heat D isto rtion
120 掳F ASTM D -648
Tem pera ture
Water Absorption (24
0.0004 ASTM D -570
hours):
Thi s i nfo rm a tio n i s fu rn is he d w ith o ut w a rra n ty, re pr es e nta tio n , in d uc em e n t, o r l ice n se o f a n y k in d , e x ce pt th a t i s i s
http://www.bonstone.com/tds/technical data.asp 3/4/2004
Bonstone Materials Corporation Page 2 of 2
ac cu ra te to the b e st of B on s to n e Ma te ria l C o rp o ra tio n 's ( BM C ) kn o wl e dg e o r ob ta in e d fr om so u rce s b e li e ve d b y B MC to
be a ccu ra te , an d BM C do e s n o t a ss u me a ny le g al re sp o ns ib il ity fo r u se o f re li an ce u p on sa m e . U s er m u st d ete rm in e if
th e p ro du ct, p ro ce ss , o r i n fo rm a tio n de sc ri be d is s u ita bl e to th e i n te n d ed a p pl ic a ti o n. B efo re u si ng a ny ch e mi ca l, re a d i ts
la b el an d Ma te ri al Sa fe ty D ata Sh e e t.
Bonstone庐 Materials Corporation
707 Swan Drive 鈥? Mukwonago, WI 53149
Local (262) 363-9877 鈥? Toll-Free (800) 425-2214
Fax (262) 363-9879 鈥? Email general@ bons tone.com
漏 1999-2002 Bonstone Materials Corporation.
http://www.bonstone.com/tds/technical data.asp 3/4/2004
|