MSDS PAGE: CAS N/A MSDS technologylubricants_com---sumtech_sg

Material Safety Data Sheet
Product Name: SUMTECH SG 460
Date: September 29, 2004
Printed: 09/29/04
Replaces: May 27, 2004
Page: 1 Of 4
Section 1 – Product and Company Identification

Company: Summit Industrial Products, Inc.
9010 County Road 2120
Tyler, Texas 75707
Phone: (903) 5348021
Fax: (903) 5814376
Emergency Telephone# 18004249300 (Chemtrec)

Product Name: Sumtech 460
Product Use: Lubricating Paste

Section 2 �? OSHA Hazardous Ingredients

Ingredient TLV PEL
Synthetic Hydrocarbon Oil N/Ap N/Ap
Lithium Soap Thickener N/Ap N/Ap
Mineral Oil 5 mg/m3 5 mg/m3
Zinc Compound N/Ap N/Ap

Section 3 Hazards Identification

Eye Contact: May cause mild irritation upon immediate contact.
Skin contact: Prolonged or repeated contact may cause the removal of skin oils, possibly leading to
irritation or dermatitis.
Inhalation: Vapor inhalation under ambient conditions will not occur. The inhalation of vapors
(generated at extremely high temperature only) or mist may cause a mild irritation of the mucous
membranes of the upper respiratory tract. Harmful concentrations of mists and/or vapors are unlikely to
occur through reasonable and customary use of this product.
Ingestion: No acute or chronic effects expected. However, minute amounts aspirated into the lungs during
ingestion or vomiting may cause mild to severe pulmonary injury.

Section 4 Emergency and First Aid Procedures

After contact with eyes: Flush eyes with plenty of water for 15 minutes. If irritation persists, or if an
infection develops, seek medical attention.
After contact with skin: Wash off with soap and plenty of water. Apply skin cream if necessary. Seek
medical attention if irritation or infection occurs. Remove contaminated clothing and wash before reuse.
After inhalation: If overcome by product vapor heated to extreme temperatures, immediately move from
exposure and get medical attention. If breathing is irregular, start resuscitation or administer oxygen if
available. If overexposed to mist, remove from further exposure until excessive mist condition subsides.
After ingestion: If large amounts are swallowed, do not induce vomiting. Get medical attention.
Advice to doctor: Treat symptomatically.
Do not induce vomiting.  Get medical attention
After ingestion:

The information herein is given in good faith, but without warranty, express or implied.  All risks of use of
the product are therefore assumed by the user.  Appropriate warnings and safe handling procedures must be
provided to handlers and users.
Material Safety Data Sheet
Product Name: SUMTECH SG 460
Date: September 29, 2004
Printed: 09/29/04
Replaces: May 27, 2004
Page: 2 Of 4

Section 5 Exposure Controls

Wear safety goggles if splashes may occur.  Do not wear contact lenses
Eye protection:
when using chemicals.
Wear chemical resistant gloves
Hand protection:
Wear clean, bodycovering clothing to minimize dermal exposure.
Body protection:
Under normal conditions of use, no special ventilation is required; however,
Ventilation:
if vaporized or misted, use local exhaust if possible.
No special respiratory protection is required.  However, if product is
Respiratory protection:
overheated beyond conditions of normal use, or misted, wear the
appropriate NIOSHapproved respiratory protection.
Other protection measures: Safety showers, eye wash fountains, and washing facilities should be
readily available.

Section 6 – Fire Fighting Measures

Flash point: N/Av Method: ASTM D 92
Lower explosion limit: N/Av
Upper explosion limit: N/Av
Extinguishing media: Water spray, foam, dry powder, carbon dioxide (CO2)
Unusual fire and explosion hazards: Empty metal containers retain product residue. Do not
pressurize, cut, weld, drill, solder or expose container to heat, flame, sparks, or other sources of ignition:
it may explode, causing serious injury or death. Exposure to heat builds up pressure in container. Cool
with water spray.
Special fire Fighting Procedures: If leak or spill has not ignited, use water spray to disperse any vapor
and to flush spills away from ignition sources. Use selfcontained breathing apparatus for enclosed or
confined spaces or as otherwise needed. Do not use direct stream of water, material may float and reignite.

Section 7 – Accidental Release Measures

If product leaks or is inadvertently spilled, eliminate ignition sources and isolate surrounding spill area with
the proper containment system to prevent the spill from reaching waterways.  Add absorbent and soak up
the product.  Collect product and absorbent, place in a chemical waste container for proper disposal.

Section 8 �? Handling and Storage
Avoid contact with skin and remove soiled or soaked clothing.  Wash hands with soap and water before
eating drinking and/or smoking.  Clean skin thoroughly after work and if necessary, apply skin cream.

Store product under normal temperature and pressure.
Store product away from heat sources and food products.

The information herein is given in good faith, but without warranty, express or implied.  All risks of use of
the product are therefore assumed by the user.  Appropriate warnings and safe handling procedures must be
provided to handlers and users.
Material Safety Data Sheet
Product Name: SUMTECH SG 460
Date: September 29, 2004
Printed: 09/29/04
Replaces: May 27, 2004
Page: 3 Of 4

Section 9 Physical and Chemical Properties

Boiling Point: N/Av
Pour Point: N/Av
Vapor Pressure (mm Hg.): N/Av
Vapor Density (Air = 1 ): N/Av
Solubility in Water: Insoluble
Specific gravity (H20 = 1): 0.89
Evaporation rate (ether = 1): N/Av
Appearance and odor: Yellowish paste with a neutral odor.

Section 10 Stability and Reactivity

Stability: Stable
Conditions to avoid: Open flames and other sources of heat
Materials to avoid: Strong oxidizing agents such as pure oxygen
Hazardous decomposition products: Fumes, smoke, carbon monoxide and carbon dioxide.
Hazardous polymerization: Will not occur.

Section 11 �? Toxicological Information

Acute toxicity: N/Av for this product.
Chronic toxicity: N/Av for this product.

Section 12 �? Disposal Considerations

Under RCRA, it is the user’s responsibility to determine, at the time of disposal, whether the product meets
any of the criteria for a hazardous waste defined in 40 CFR 261 Subpart C.

Section 13 Transportation Information
Proper Shipping Name Hazard Class or Division UN ID Packing Group
N/Ap

The information herein is given in good faith, but without warranty, express or implied.  All risks of use of
the product are therefore assumed by the user.  Appropriate warnings and safe handling procedures must be
provided to handlers and users.
Material Safety Data Sheet
Product Name: SUMTECH SG 460
Date: September 29, 2004
Printed: 09/29/04
Replaces: May 27, 2004
Page: 4 Of 4

Section 14 Regulatory Information

All product components comply with all applicable rules and orders under the Toxic Substance Control
Act (TSCA).
The Zinc Compound (~1) in this product is a SARA Title III Section 313 chemical.

Section 15 Additional Information

HMIS Rating: Health 1 Flammability 1 Reactivity 0 Personal Protection B

Unk. = Unknown N/Ap = Not Applicable N/Av = Not Available ~ = Approximately

The information herein is given in good faith, but without warranty, express or implied.  All risks of use of
the product are therefore assumed by the user.  Appropriate warnings and safe handling procedures must be
provided to handlers and users.

ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP

NAME	CAS
technologylubricants_com---pgi_68.asp	9003-13-8
technologylubricants_com---pgs10x_pds.asp	N/A
technologylubricants_com---pgs2_0507.asp	31694-55-0
technologylubricants_com---pgs2_pds.asp	N/A
technologylubricants_com---pgsseries_pds.asp	N/A
technologylubricants_com---pgs_10xa.asp	9038-95-3
technologylubricants_com---pm1740.asp	64742-54-7 64741-88-4 68649-42-3
technologylubricants_com---prem_go_mp.asp	N/A
technologylubricants_com---procool_premixed_coolant.asp	N/A
technologylubricants_com---proeco346.asp	N/A
technologylubricants_com---proeco__300_series_.asp	N/A
technologylubricants_com---psseries.asp	N/A
technologylubricants_com---psv_22.asp	N/A
technologylubricants_com---ps_150.asp	N/A
technologylubricants_com---ps_200.asp	N/A
technologylubricants_com---ps_400.asp	N/A
technologylubricants_com---pyroplex_blue.asp	64742-01-4 64742-58-1
technologylubricants_com---pyroplex_grease.asp	N/A
technologylubricants_com---rabseries_pds.asp	N/A
technologylubricants_com---rht68.asp	N/A
technologylubricants_com---rhtseries_pds.asp	N/A
technologylubricants_com---rlx_super_40.asp	N/A
technologylubricants_com---rock_drill_msds.asp	N/A
technologylubricants_com---rpaseries_pds.asp	N/A
technologylubricants_com---rust-o-lene_110.asp	N/A
technologylubricants_com---sh_series_32_46_68.asp	N/A
technologylubricants_com---sliderite.asp	N/A
technologylubricants_com---sublime.asp	7647-01-0
technologylubricants_com---sumclean.asp	111-76-2 27323-41-7
technologylubricants_com---sumtechaq32.asp	8012-95-1
technologylubricants_com---sumtechgrease.asp	N/A
technologylubricants_com---sumtechsg_pds.asp	N/A
technologylubricants_com---sumtech_sg_220.asp	N/A
technologylubricants_com---sumtech_sg_460.asp	N/A
technologylubricants_com---superhydraulicoil.asp	N/A
technologylubricants_com---super_all_season.asp	N/A
technologylubricants_com---supracoolant.asp	N/A
technologylubricants_com---supra_coolant.asp	9003-13-8 16958-92-2 68515-47-9
technologylubricants_com---synconhp_msds.asp	N/A
technologylubricants_com---synconsynrooil.asp	N/A
technologylubricants_com---syncon_synthetic_r&o_32_46_68_100.asp	N/A
technologylubricants_com---syndustrialro32_150.asp	N/A
technologylubricants_com---syngard_32_68.asp	N/A
technologylubricants_com---syngearfgseries.asp	N/A
technologylubricants_com---syngear_75w_90.asp	68037-01-4 151006-63-2 151006-62-1
technologylubricants_com---syngear_fg_pg150.asp	9038-95-3
technologylubricants_com---syngear_fg_pg220.asp	9038-95-3
technologylubricants_com---syngear_fg_pg460.asp	9038-95-3
technologylubricants_com---syngear_fg_pg680.asp	9038-95-3
technologylubricants_com---syngear_pg220.asp	9038-95-3