www.tra-con.com
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name: Date Printed: 2/10/2006
TRA-BOND 2151 Hardener
Revision Date: 2/9/2006
TRA-CON, INC.
45 Wiggins Avenue Revision: D
Bedford, MA 01730
781-275-6363
1-800-872-2661
Emergency Telephone: 1-800-424-9300 (24 hours, CHEMTREC)
2. COMPOSITION/INFORMATION ON INGREDIENTS
TWA STEL Ceiling
Component CAS Number %
OSHA
ACGIH ppm mg/m3 ppm mg/m3 ppm mg/m3
1-propanamine,3,3'-(oxybis(2,1-- 004246-51-9 75-85
ethanediyloxy))bis-
Bisphenol A/Epichlorohydrin Based Epoxy 025068-38-6 10-20
Resin
3. HAZARDS IDENTIFICATION
Effects of Overexposure Contact may serious eye, mouth and/or skin irritation or burns; corrosive. Material is a
strong sensitizer. Ames test negative.
4. FIRST AID MEASURES
Eyes Flush with water, get medical attention.
Skin Wash with soap and water; remove contaminated clothing.
Inhalation Remove to fresh air.
Ingestion No known antidote but give milk or water; do NOT induce vomitting if swallowed; get
medical attention.
5. FIREFIGHTING MEASURES
Flashpoint > 250掳F
Flashpoint Method PMCC
Extinguishing Media Dry chemicals, chemical foam, carbon dioxide, water.
Special Firefighting Measures Avoid breathing smoke. Addition of water may reduce flame intensity.
Fire and Explosion Hazards Toxic gases may be liberated; handle as combustible; store in a cool place.
Flammable Limits N/AV
LEL N/A
UEL N/A
6.ACCIDENTAL RELEASE MEASURES
Spill and Leak Procedures Prevent skin and eye contact. Soak up in absorbent material, or scrape up, and transfer
to disposal container. Wipe up remaining residue with solvents, observing solvent
flammability cautions, or use detergents.
7. HANDLING AND STORAGE
Handling and Storage For industrial use only. WARNING: May cause sensitization, irritation or other allergic
responses. Avoid eye and/or skin contact and prolonged inhalation of vapors.
Special Sensitivity Store in a cool place in closed containers.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Local Exhaust Recommended
Mechanical Exhaust Recommended
Eye Protection Requirements Safety glasses or goggles
Glove Requirements Rubber or plastic disposable.
QAF-1058 Rev D Date Printed: 2/10/2006 Page 1 of 8 2151 Hardener
Other Protection As required to prevent all body contact; eye bath and/or safety shower.
Respirator Requirements Air supplied or organic canister, mask in confined areas.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance and Odor Light amber liquid, slight amine odor.
Boiling Point (掳F) > 400
Solubility in Water high
Specific Gravity (H2O=1) 1.0
Evaporation Rate (BuAc=1) low
Vapor Pressure (mm Hg.) low
Vapor Density (air = 1) >2
Percent Volatile ND
10. STABILITY AND REACTIVITY
Stability Stable
Conditions to Avoid (Stability) Avoid uncontrolled excess heating over long periods; avoid uncontrolled amine reactions.
Incompatibility (Materials to Avoid) Strong acids and bases, strong oxidizing agents.
Hazardous Decomposition Products Carbon monoxide, carbon dioxide, aldehydes, nitrogen oxides, thermal products.
Hazardous Polymerization Will Not Occur
Conditions to Avoid (Reactivity) High temperatures, strong acids; certain organics, metallic acids.
11. TOXICOLOGICAL INFORMATION
Primary Entry Route(s) Skin, eyes, inhalation.
Oral, LD50 Ingestion > 5000 mg/kg.
12. ECOLOGICAL INFORMATION
Not available
13. DISPOSAL CONSIDERATIONS
Waste Disposal Methods Dispose of as hazardous waste according to local, state and federal regulations. Disposal
method can be land burial or chemical incineration as regulated by all governmental
agencies.
14. TRANSPORTATION INFORMATION
Not Applicable
15. REGULATORY INFORMATION
TSCA: All components are on the TSCA inventory.
The information given and the recommendations made herein apply to our product(s) alone and are not combined with other product(s). Such are
based on our research and on data from other reliable soruces and are believed to be accurate. no guaranty of accuracy is made. it is the purchaser's
responsibility before using any product to verify this data under their own operating conditions and to determine whether the product is suitable for their
purposes.
16. OTHER INFORMATION
This MSDS applies to all sizes of 2151 including but not limited to the following part numbers:
BA-2151 BB-2151 BC-2151 BD-2151
BE-2151 CBA-4908 CBA-4915 CBA-4924
CBA-4949 CBB-4383 CBC-4950 CHECF-4919
CQ-2151 HBAB-2151 HEBF-2151 HECF-2151
HEQP-2151
MSDS Date: 2/9/2006 Revision: D
QAF-1058 Rev D Date Printed: 2/10/2006 Page 2 of 8 2151 Hardener
www.tra-con.com
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name: Date Printed: 2/10/2006
TRA-BOND 2151 Pre-Mixed and Frozen
Revision Date: 2/9/2006
TRA-CON, INC.
45 Wiggins Avenue Revision: D
Bedford, MA 01730
781-275-6363
1-800-872-2661
Emergency Telephone: 1-800-424-9300 (24 hours, CHEMTREC)
2. COMPOSITION/INFORMATION ON INGREDIENTS
TWA STEL Ceiling
Component CAS Number %
OSHA
ACGIH ppm mg/m3 ppm mg/m3 ppm mg/m3
Phenol,4,4'-(1-methylethylidene)bis-, 025068-38-6 20 - 40
polymer with (chloromethyl) oxirane
Silica,amorphous,fumed, crystilline-free 112945-52-5 <5
Phenol, 4,4'-(1-methylethylidene)bis- 068585-28-4 < 10
,polymer with (chloromethyl) oxirane,
reaction products wtih 3,3'-[oxybis(2,1-
ethanediyloxy)]bis [1-propanamine]
3. HAZARDS IDENTIFICATION
Effects of Overexposure Repeated contact or breathing of vapors may cause irritation; material is also a strong
sensitizer. Eye and skin contact may cause transient irritation.
4. FIRST AID MEASURES
Eyes Flush with water, get medical attention.
Skin Wash with soap and water; remove contaminated clothing.
Inhalation Remove to fresh air.
Ingestion No known antidote but give milk or water; induce vomitting if large amount swallowed.
5. FIREFIGHTING MEASURES
Flashpoint 164掳F
Flashpoint Method setaflash
Extinguishing Media Dry chemicals, chemical foam, carbon dioxide, water.
Special Firefighting Measures Avoid breathing smoke. Use self-contained breathing apparatus.
Fire and Explosion Hazards Toxic gases may be liberated; handle as combustible; store in a cool place.
Flammable Limits N/AV
LEL N/A
UEL N/A
6.ACCIDENTAL RELEASE MEASURES
Spill and Leak Procedures Prevent skin and eye contact. Soak up in absorbent material or scrape up and transfer to
disposal container. Wipe up remaining residue with solvents, observing solvent
flammability cautions or use detergents.
7. HANDLING AND STORAGE
Handling and Storage For industrial use only. WARNING: May cause sensitization, irritation or other allergic
responses. Avoid eye and/or skin contact and prolonged inhalation of vapors.
Special Sensitivity Store in freezer at minium -40掳F. Thaw cartridges in upright position, dispensing tip up, to
release air in tip cap, if any.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
QAF-1058 Rev D Date Printed: 2/10/2006 Page 3 of 8 2151 Pre-Mixed and Frozen
Local Exhaust Recommended
Mechanical Exhaust Recommended
Eye Protection Requirements Safety glasses or goggles
Glove Requirements Rubber or plastic disposable.
Other Protection As required to prevent all body contact; eye bath and/or safety shower.
Respirator Requirements Air supplied or organic canister, mask in confined areas.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance and Odor Blue, medium viscosity liquid, slight amine odor.
Boiling Point (掳F) 340
Solubility in Water partial
Specific Gravity (H2O=1) 2.3
Evaporation Rate (BuAc=1) low
Vapor Pressure (mm Hg.) low
Vapor Density (air = 1) >2
Percent Volatile ND
10. STABILITY AND REACTIVITY
Stability Unstable
Conditions to Avoid (Stability) Avoid uncontrolled excess heating over long periods; avoid uncontrolled amine reactions. Will
react at room temp. Keep frozen at all times.
Incompatibility (Materials to Avoid) Carbon monoxide, carbon dioxide, aldehydes, phenol.
Hazardous Decomposition Products Carbon monoxide, carbon dioxide, aldehydes, nitrogen oxides.
Hazardous Polymerization May Occur
Conditions to Avoid (Reactivity) Moderate temperatures, strong acids; certain organics, metallic acids.
11. TOXICOLOGICAL INFORMATION
Primary Entry Route(s) Skin, eyes, inhalation
Oral, LD50 Ingestion LD50 900 mg/kg. Dermal LD50 > 20 ml/kg. Inhalation LC50 > 3500 ppm.
12. ECOLOGICAL INFORMATION
Not available
13. DISPOSAL CONSIDERATIONS
Waste Disposal Methods Dispose of as hazardous waste according to local, state and federal regulations. Disposal
method can be land burial or chemical incineration as regulated by all governmental
agencies.
14. TRANSPORTATION INFORMATION
Not Applicable
15. REGULATORY INFORMATION
TSCA: All components are on the TSCA inventory.
The information given and the recommendations made herein apply to our product(s) alone and are not combined with other product(s). Such are
based on our research and on data from other reliable soruces and are believed to be accurate. no guaranty of accuracy is made. it is the purchaser's
responsibility before using any product to verify this data under their own operating conditions and to determine whether the product is suitable for their
purposes.
16. OTHER INFORMATION
This MSDS applies to all sizes of 2151 including but not limited to the following part numbers:
BA-2151 BB-2151 BC-2151 BD-2151
BE-2151 CBA-4908 CBA-4915 CBA-4924
CBA-4949 CBB-4383 CBC-4950 CHECF-4919
CQ-2151 HBAB-2151 HEBF-2151 HECF-2151
HEQP-2151
QAF-1058 Rev D Date Printed: 2/10/2006 Page 4 of 8 2151 Pre-Mixed and Frozen
MSDS Date: 2/9/2006 Revision: D
QAF-1058 Rev D Date Printed: 2/10/2006 Page 5 of 8 2151 Pre-Mixed and Frozen
www.tra-con.com
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name: Date Printed: 2/10/2006
TRA-BOND 2151 Resin
Revision Date: 2/9/2006
TRA-CON, INC.
45 Wiggins Avenue Revision: D
Bedford, MA 01730
781-275-6363
1-800-872-2661
Emergency Telephone: 1-800-424-9300 (24 hours, CHEMTREC)
2. COMPOSITION/INFORMATION ON INGREDIENTS
TWA STEL Ceiling
Component CAS Number %
OSHA
ACGIH ppm mg/m3 ppm mg/m3 ppm mg/m3
Phenol,4,4'-(1-methylethylidene)bis-, 025068-38-6 10 - 30
polymer with (chloromethyl) oxirane
n-Butyl glycidyl ether 002426-08-6 <1 50 270 -- -- -- --
25 133 -- -- -- --
COMMENTS: a. NIOSH - Value based on 15
minutes.
a-Alumina 001344-28-1 70 - 90 -- 15,5a -- -- -- --
-- 10b -- -- -- --
COMMENTS: SYN - Aluminum oxide. a. OSHA, CANADA -
total dust; respirable fraction respectively. b. ACGIH -
Inhalable (total) particulate matter containing no asbestos
and < 1% crystalline
silica.
Silica,amorphous,fumed, crystilline-free 112945-52-5 <1
Epichlorohydrin 000106-89-8 <1 5 19 -- -- -- --
0.5 1.9 -- -- -- --
COMMENTS: a. NIOSH - Lowest feasible
concentration.
3. HAZARDS IDENTIFICATION
Effects of Overexposure Skin or eye contact or breathing of vapors may cause irritation; material is also a strong
sensitizer. Chronic exposure may be mutagenic.
4. FIRST AID MEASURES
Eyes Flush with water, get medical attention.
Skin Wash with soap and water; remove contaminated clothing.
Inhalation Remove to fresh air.
Ingestion No known antidote but give milk or water; induce vomitting if large amount swallowed.
5. FIREFIGHTING MEASURES
Flashpoint 164掳F
Flashpoint Method setaflash
Extinguishing Media Dry chemicals, chemical foam, carbon dioxide, water.
Special Firefighting Measures Avoid breathing smoke. Addition of water may reduce flame intensity.
QAF-1058 Rev D Date Printed: 2/10/2006 Page 6 of 8 2151 Resin
Fire and Explosion Hazards Toxic gases may be liberated; handle as combustible; store in a cool place.
Flammable Limits N/AV
LEL N/A
UEL N/A
6.ACCIDENTAL RELEASE MEASURES
Spill and Leak Procedures Prevent skin and eye contact. Soak up in absorbent material or scrape up and transfer to
disposal container. Wipe up remaining residue with solvents, observing solvent
flammability cautions or use detergents.
7. HANDLING AND STORAGE
Handling and Storage For industrial use only. WARNING: May cause sensitization, irritation or other allergic
responses. Avoid eye and/or skin contact and prolonged inhalation of vapors.
Special Sensitivity Store in a cool place in closed containers. Handle per Hazard Potential of Hardener.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Local Exhaust Recommended
Mechanical Exhaust Recommended
Eye Protection Requirements Safety glasses or goggles
Glove Requirements Rubber or plastic disposable.
Other Protection As required to prevent all body contact; eye bath and/or safety shower.
Respirator Requirements Air supplied or organic canister, mask in confined areas.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance and Odor Blue, medium viscosity paste, slight sweet odor.
Boiling Point (掳F) > 350
Solubility in Water low
Specific Gravity (H2O=1) 2.5
Evaporation Rate (BuAc=1) low
Vapor Pressure (mm Hg.) <1
Vapor Density (air = 1) >1
Percent Volatile ND
10. STABILITY AND REACTIVITY
Stability Stable
Conditions to Avoid (Stability) Avoid uncontrolled excess heating over long periods; avoid uncontrolled amine reactions.
Incompatibility (Materials to Avoid) Strong acids and bases, strong oxidizing agents.
Hazardous Decomposition Products Carbon monoxide, carbon dioxide, aldehydes, phenol.
Hazardous Polymerization Will Not Occur
Conditions to Avoid (Reactivity) High temperatures, strong acids; certain organics, metallic acids.
11. TOXICOLOGICAL INFORMATION
Primary Entry Route(s) Skin, eyes, inhalation.
Oral, LD50 Ingestion LD50 900 mg/kg. Dermal LD50 > 20 ml/kg. Inhalation LC50 > 3500 ppm.
Other Notes on Toxicity Considered Mutagenic
12. ECOLOGICAL INFORMATION
Not available
13. DISPOSAL CONSIDERATIONS
Waste Disposal Methods Dispose of as hazardous waste according to local, state and federal regulations. Disposal
method can be land burial or chemical incineration as regulated by all governmental
agencies.
14. TRANSPORTATION INFORMATION
Not Applicable
QAF-1058 Rev D Date Printed: 2/10/2006 Page 7 of 8 2151 Resin
15. REGULATORY INFORMATION
TSCA: All components are on the TSCA inventory.
SARA TITLE III:
This product contains the following substances which are on the SARA, Title III, Section 313 list:
CAS # Chemical Name % in Product Reportable Qty
000106-89-8 Epichlorohydrin <1 0.1
CALIFORNIA PROPOSITION 65 CHEMICALS
000106-89-8 Epichlorohydrin <1
FLORIDA TOXIC SUBSTANCE LIST
000106-89-8 Epichlorohydrin <1
MASSACHUSETTS HAZARDOUS SUBSTANCE LIST
000106-89-8 Epichlorohydrin <1
MICHIGAN CRITICAL MATERIALS LIST
000106-89-8 Epichlorohydrin <1
MINNESOTA HAZARDOUS SUBSTANCE LIST
001344-28-1 a-Alumina 70 - 90
000106-89-8 Epichlorohydrin <1
NEW YORK HAZARDOUS SUBSTANCE LIST
000106-89-8 Epichlorohydrin <1
The information given and the recommendations made herein apply to our product(s) alone and are not combined with other product(s). Such are
based on our research and on data from other reliable soruces and are believed to be accurate. no guaranty of accuracy is made. it is the purchaser's
responsibility before using any product to verify this data under their own operating conditions and to determine whether the product is suitable for their
purposes.
16. OTHER INFORMATION
This MSDS applies to all sizes of 2151 including but not limited to the following part numbers:
BA-2151 BB-2151 BC-2151 BD-2151
BE-2151 CBA-4908 CBA-4915 CBA-4924
CBA-4949 CBB-4383 CBC-4950 CHECF-4919
CQ-2151 HBAB-2151 HEBF-2151 HECF-2151
HEQP-2151
MSDS Date: 2/9/2006 Revision: D
QAF-1058 Rev D Date Printed: 2/10/2006 Page 8 of 8 2151 Resin
|