Personalformulator.com
97 S. Red Willow Rd.
Evanston, WY 82930
US 1-800-426-2457 Ext. 1003
Material Safety Data Sheet
Propylparaben
1. Product Identification 7. Hazards Identification
Product Name: Propylparaben General: Signs and symptoms of exposure to this material through
INCI Name: Propylparaben breathing, swallowing, and/or passage of the material through the skin may
Chem. N.: No data include: stomach or intestinal upset (nausea, vomiting, diarrhea), irritation
CAS Number: 94-13-3 (nose, throat, airways).
EINECS Number: No data Inhalation: This material is a dust or may produce dust.
Eye Contact: Can cause eye irritation. Symptoms include stinging,
2. Physical and Chemical Properties tearing, redness, and other skin damage.
Skin Contact: Can cause skin irritation. Symptoms may include
Melting Point: No data redness and burning of skin, and other skin damage.
Boiling Point: Not applicable Ingestion: Swallowing small amounts of this material during normal
Refractive Index: No data handling is not likely to cause harmful effects. Swallowing large amounts
Evaporation Rate: Not applicable may be harmful.
Specific Gravity: .000
8. First Aid Measures
Solubility in Water: No data
pH Value: Not applicable Eyes: If symptoms develop, immediately move individual away from
Appearance & Odor: Solid, powder, white crystalline exposure and into fresh air. Flush eyes gently with water for at least 15
minutes while holding eyelids apart; seek immediate medical attention.
3. Stability and Reactivity Skin: Remove contaminated clothing. Wash exposed area with soap
and water. If symptoms persist, seek medical attention. Launder clothing
Chemical Stability: Stable
before reuse.
Incompatibility: Avoid contact with: strong oxidizing agents.
Inhalation: If symptoms develop, move individual away from exposure
Hazardous Decomposition: May form: carbon dioxide and carbon
and into fresh air. If symptoms persist, seek medical attention. If breathing
monoxide, phenols.
is difficult administer oxygen. Keep person warm and quiet; seek immediate
Hazardous Polymerization: Product will not undergo hazardous
medical attention.
polymerization.
Ingestion: Seek medical attention. If individual is drowsy or
4. Handling and Storage unconscious, do not give anything by mouth; place individual on the left side
with the head down. Contact a physician, medical facility, or poison control
Containers of this material may be hazardous when emptied. Since
center for advice about whether to induce vomiting. If possible, do not leave
emptied containers retain product residues (vapor, liquid, and/or solid), all
individual unattended.
hazard precautions given in the data sheet must be observed.
9. Fire Fighting Measures
5. Accidental Release Measures
Flash Point: Not applicable
Small spill: Sweep up material for disposal or recovery.
Auto-ignition Temp: No data
Large spill: Shovel material into containers. Thoroughly sweep area of
Extinguishing Media: carbon dioxide, dry chemical
spill to clean up any residual material. Persons not wearing protective
Fire Fighting Procedures: Wear a self-contained breathing apparatus
equipment should be excluded from area of spill until clean up has been
with a full-face piece operated in the positive pressure demand mode with
completed.
appropriate turnout gear and chemical resistant personal protective
6. Exposure Controls & Personal Protection equipment. Refer to the personal protective equipment section of this
MSDS.
Respiratory Protection: If needed, use a NIOSH/MSHA jointly
10. Toxicological Information
approved dust respirator. (Ask your safety representative.)
Protective Clothing: Wear resistant gloves (consult your safety
Acute Oral LD50: No data
equipment supplier). Wear normal work clothing covering arms and legs.
Dermal and Eye Irritation Test: No data
Chemical splash goggles in compliance with OSHA regulations are advised;
Carcinogenicity: No data
however, OSHA regulations also permit other type safety glasses. Consult
Mutagenicity: No data
your safety representative.
Other Protective Measures: Provide sufficient mechanical (general
11. Disposal Considerations
and/or local exhaust) ventilation to maintain exposure below TLV(s).
Dispose of in accordance with all applicable local, state and federal
regulations.
Important Notice: The information presented herein is based on experimental data submitted by the manufacturers
of the raw materials and is considered scientifically correct; however, no warrant or representation, express or implied, is
made as to the accuracy or suitability of this information for application to the purchaser鈥檚 intended purpose or for
consequences of its use and we assume no responsibility for any loss, damage or expense, direct or consequential, arising
out of its use. Use these materials only as directed. If you have any questions regarding the proper interpretation of this
sheet or the meanings of any terms used, we strongly urge you to speak with your physician. For further information
concerning product safety and proper use, call the number listed on the front of the MSDS.
|