Material Safety Data Sheet
TM
BLUE OX 901 - Polyurethane Adhesive
庐
TELEPHONE 715-832-4557
1. Product Information
Product Name BX901-B
Proper Shipping Name NA
Product Class Polyol
U.S.D.O.T. Hazard Class NA
U.S.D.O.T. Hazard Number NA
U.S.D.O.T. Label None
HMIS CODES: Health 1 Flammability 1 Reactivity 0
Hazard Ratings: 4 = Severe 3 = Serious 2 = Moderate 1 = Slight 0 = Minimal
2. Hazardous Ingredients
Ingredients CAS# TLV** Percent*
NJTSRN-BX901-B 鈥? 鈥?
*Major = Over 25%, Minor = 6%-25%, Trace = Under 6%, Residue = Unknown % Residue Possible
**TLV as established by ACGIH and or OSHA Standard
*** If no components are listed then this material contains non-hazardous substances according to 29CFR1910.1200.
3. Physical and Chemical Properties
Physical State Liquid
Color White
Solubility Negligible
LBS/Gallon 11.75
Vapor Density Heavier than air
Boiling Point NA
Liquid Density Lighter than water
Note: These physical data are typical values based on material tested but may vary from sample to sample. Typical values should
not be construed as a guarantee analysis of any specific lot or as specifications for the product.
4. Fire and Explosion Data
Flash Point >325藲F (PMCC)
Flammability Limits UEL % Not established
Extinguishing Media: Foam, CO2, Dry Chemical, Water Fog
Special Fire Fighting Procedures For large fires, alcohol resistant foams(ATC type) are preferred if available. General
purpose synthetic foams(including AFFF) or protein foams may function but much less
effectively. Water is not recommended but may be applied in very large quantities as
a fine spray when other extinguishing media are not available.
Unusual Fire and Explosion Hazards Full emergency equipment with self-contained breathing apparatus should be worn.
During a fire irritating, toxic gases (see Reactive Data ) and smoke are present from
decomposition/combustion. Product reacts with water. Reaction may produce heat
and/or gases.
5. Health Hazards Data
Effects of Over Exposure Acute
Eyes: Can cause eye irritation.
Skin: Can cause skin irritation. Repeated or prolonged exposure may cause sensitization. Acute:- Isocyanates
reacts with skin protein & moisture & cause irritation which may include reddening, swelling, rash,
scaling or blistering.
Ingestion: May cause nausea, vomiting or other signs of illness.
Inhalation: MDI vapors at concentrations above TLV can irritate the mucous membranes in the respiratory Tract
(nose, throat, lungs) causing a runny nose, soar throat, coughing, chest discomfort, shortness of breath
and reduced lung function. Persons with pre-existing , nonspecific bronchial hyperreactitty can respond
to concentrations below TLV with similar systems as well as asthma attack. Overexposure to isocyanates
has also been reported to cause lung damage (including decrease in lung function) which may be permanent.
6. First Aid Procedures
Eye Contact Flush immediately with clean, lukewarm water (low pressure) for at least 15 minutes while holding eye
lids open. Obtain medical attention immediately.
Skin Contact Remove contaminated clothing. Wash affected areas thoroughly with soap and water, warm water is prefer
able if readily available. Wash contaminated clothing before reuse. Contact physician if irritation occurs.
Inhalation Move to fresh air. Administer oxygen or artificial respiration as needed. Obtain medical attention.
Asthmatic 鈥搕ype symptoms may develop and may be immediate or delayed up to several hours.
Ingestion Do not give any liquids ( do not induce vomiting ). Get medical help immediately. Give 1 to 2 cups of
milk or water to drink. DO NOT GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
CONSULT PHYSICIAN IMMEDIATELY.
7. Special Protection Information.
Eye Protection Liquid chemical goggles or full-face shield.
Skin Protection Chemical resistant gloves (natural latex and neoprene recommended). Cover as much
of the exposed skin area as possible with appropriate clothing. If skin creams are
used, keep the area covered by the cream to a minimum.
Ventilation and Respiratory Protection Exhaust ventilation sufficient to keep airborne concentrations of the hazardous
constituents below TLV or other appropriate exposure limit must be utilized. When
respiratory protection is required for certain operations, use an approved positive-
pressure supplied 鈥? air respirator. Avoid breathing vapors which may be produced under
some conditions such as heating. Avoid breathing aerosols and mists. Use NIOSH/MSHA
approved respiratory protection equipment when airborne exposure is excessive.
Observe OSHA regulations for respirator use (29 CFR 1910.134)
Other Safety showers and eye wash stations should be easily accessible to the work area.
Worker training is important. Follow all label precautions.
8. Reactivity Data
Stability STABLE UNDER NORMAL STORAGE, POLYMERIZATION WILL NOT OCCUR. Product is
VERY UNSTABLE when contaminated with water.
Conditions to Avoid Avoid temperatures above 86掳F. Avoid temperatures below 64掳F. Avoid moisture.
Product can decompose at elevated temperature.
Materials to Avoid Avoid water.
Hazardous Polymerization Will not occur under normal conditions.
Decomposition Products By heat and fire: Carbon dioxide, carbon monoxide, Aldehydes, acids and other organic
substances may be formed.
9. Spill, Leak and Disposal Procedures
Action to be taken if material is
released or spilled Remove all sources of ignition. Avoid contact with material. Ventilate the area. Equip
clean-up crew with appropriate protective equipment. Persons not wearing proper
protective equipment should be excluded from the area until cleanup is complete.
Dike or impound spilled material and control further spillage if feasible. Notify appro-
priate authorities if necessary. Cover spill area with sawdust, vermiculite, or other
absorbent material; collect material in open containers. Attempt to neutralize by adding
a mixture of: water(80%), with non-ionic surfactant Tergitol TMN-10 (20%), or water
(90%), concentrated ammonia (3-8%) and detergent (2%). Add about 10 parts of
neutralizer per part of Isocyanate while mixing. Allow to stand uncover for 48 hours
to let CO2 escape. If ammonia is used, use good ventilation to prevent vapor exposure.
Large quantities may be pumped into closed, but not sealed containers. Refer to
section IX for disposal information. Remove containers to safe place and cover.
Waste Disposal Method Dispose of waste in accordance with Federal, State, and Local regulations. Incineration
is the preferred method. Empty containers must be handled with care due to product
residue. Do not heat or cut empty containers with electric or gas torch.
10. Special Precautions and Storage Data
Contact Avoid skin and eye contact. Avoid breathing vapor, mist of fumes. Ensure that all
containers are properly labeled to prevent accidental ingestion or improper disposal.
Reseal partly used containers. Wash with soap and water before eating, drinking or
using toilet facilities. Store under cool, dry conditions away from open flames and high
temperatures. Observe conditions of good industrial hygiene and safe working practice.
Storage Store indoors in a dry place away from heat between the temperatures 64 to 86掳F.
Keep containers tightly closed when not in use. Keep product from exposing to
atmospheric moisture and maintain a nitrogen atmosphere in the containers at all
times. Do not store product contaminated with water to prevent potential hazardous
reaction. Refer to section VIII of the MSDS for Reactivity and Stability data.
11. Regulatory Information
TSCA All components of this product are registered under the regulations of the Toxic
Substance Control Act.
SARA TITLE III Section 302 Extremely Hazardous Substance: None
We believe the information contained herein is current and accurate as of this date of this Material Safety Data Sheet. Since the use of this information and these opinions and the
conditions of use of this product are not under the control of ADHESIVE R&D庐, Inc. or it鈥檚 agents or distributors, it is the user鈥檚 obligation to determine the conditions of safe use of
this product. The buyer should conduct its own tests of this product before use to determine proper preparation technique and suitability for proposed application. ADHESIVE R&D庐,
Inc. warrants that the product conforms with ADHESIVE R&D庐鈥檚 written specifications, and is free from defects and disclaims all other warranties, expressed or implied and is
not responsible for loss claim of damages resulting from the use of it鈥檚 products. Rev 01/03
|