Material Safety Data Sheet
TM
BLUE OX EP 100 PART B
庐
TELEPHONE 715-832-4557
1. Product Information
Product Name EP 100 B
Proper Shipping Name 2,4,6 tri (dimethylaminomethyl) phenol
Product Class Epoxy Hardeners
Chemical Family Mercaptan Amine Blend, tertiary amine
U.S.D.O.T. Hazard Class Corrosive Liquid
U.S.D.O.T. Hazard Number UN 1760
U.S.D.O.T. Label Corrosive Liquid
HMIS CODES Health 3 Flammability 1 Reactivity 0
Hazard Ratings 4 = Severe 3 = Serious 2 = Moderate 1 = Slight 0 = Minimal
2. Hazardous Ingredients
Ingredients CAS# TLV** Percent*
tris phenol
(2,4,6 tridimethylaminomethyl) 90-72-2 5ppm TWA 1-25%
*Major = Over 25%, Minor = 6%-25%, Trace = Under 6%, Residue = Unknown % Residue Possible
**TLV as established by ACGIH and or OSHA Standard
*** If no components are listed then this material contains nonhazardous substances according to 29CFR1910.1200.
3. Physical and Chemical Properties
Physical State Liquid
Color Clear
Specific Gravity 1.15
LBS/Gallon 9.580
Solubility in Water None
4. Fire and Explosion Data
Flash Point 215藲F (CC)
Flammability Classification Combustible
Extinguishing Media: Foam, CO2, Dry Chemical, Water
Special Fire Fighting Procedures
Unusual Fire and Explosion Hazards Full emergency equipment with self-contained breathing apparatus should be worn.
During a fire irritating, toxic gases (see Reactive Data) and smoke are present from
decomposition/combustion. Closed container may explode when exposed to extreme
heat. Solid residue will support combustion when water has evaporated.
5. Health Hazards Data
Effects of Over Exposure Acute
Eyes: Can cause eye irritation and possibly permanent injury.
Skin: Can cause sever skin irritation. Substance can be aabsorbed through the skin in harmful amounts.
Ingestion: May cause nausea, vomiting, abdominal pain or other signs of illness.
Inhalation: Vapors or fumes can irrate nose and throat.
Chronic: Prolonged skin contact may cause delayed and serious injury.
6. First Aid Procedures
Eye Contact Flush immediately with clean, lukewarm water (low pressure) for at least 15 minutes while holding eye
lids open. Obtain medical attention immediately.
Skin Contact Remove contaminated clothing. Wash affected areas thoroughly with soap and water. Wash contaminated
clothing before reuse. Contact physician if irritation occurs.
Inhalation Move to fresh air. Administer oxygen or artificial respiration as needed. Obtain medical attention.
Ingestion Induce vomiting only on the advise of a physician. Treat Symptomatically. CONSULT PHYSICIAN IMMEDIATELY.
Do not give anything by mouth to an unconscious person.
7. Special Protection Information.
Eye Protection Liquid chemical goggles or full-face shield. Contact lenses should not be worn.
Skin Protection Chemical resistant gloves (natural latex and neoprene recommended). Cover as much
of the exposed skin area as possible with appropriate clothing. If skin creams are
used, keep the area covered by the cream to a minimum.
Ventilation and Respiratory Protection Exhaust ventilation sufficient to keep airborne concentrations of the hazardous
constituents below TLV or other appropriate exposure limit must be utilized. Exhaust
air may need to be cleaned by scrubbers or filters to reduce environmental contami-
nation. Curing ovens must be ventilated to prevent the build up of explosive atoms-
pheres and to prevent off gases from entering the work place. In addition, a respirator
that is recommended or approved for use in organic vapor containing environments
(air purifying or fresh air supplied) may be necessary. In spray applications an organic
vapor/particulate respirator or air supplied unit is necessary. Consider the type of
application and environmental concentrations. Take into account other materials being
used concurrently. Observe OSHA regulations for respiratory use (29CFR1910.134).
Other Safety showers and eye wash stations should be easily accessible to the work area.
Worker training is important. Follow all label precautions.
8. Reactivity Data
Stability Stable under normal storage, polymerization will not occur.
Incompatibility/Avoid Acids, oxidizing materials, aldehydes, keystones and organic halides
Hazardous Decomposition Products by Fire CO, CO2, Oxides of nitrogen, ammonia and other unknown organic compounds.
9. Spill, Leak and Disposal Procedures
Action to be taken if material is
released or spilled Remove all sources of ignition. Avoid contact with material. Ventilate the area. Equip
clean-up crew with appropriate protective equipment. Persons not wearing proper
protective equipment should be excluded from the area until cleanup is complete.
Dike or impound spilled material and control further spillage if feasible. Notify appro-
priate authorities if necessary. Cover spill area with sawdust, vermiculite, or other
absorbent material; collect material in open containers. Remove containers to safe
place and cover. Flush spill area with water.
Waste Disposal Method Dispose of waste in accordance with Federal, State, and Local regulations.
10. Special Precautions and Storage Data
Avoid skin and eye contact. Avoid breathing vapor, mist of fumes. Ensure that all containers are properly labeled to prevent accidental
ingestion or improper disposal. Reseal partly used containers. Wash with soap and water before eating, drinking or using toilet
facilities. Store under cool, dry conditions away from open flames and high temperatures. Observe conditions of good industrial
hygiene and safe working practice.
11. Regulatory Information
TSCA All components of this product are registered under the regulations of the Toxic
Substance Control Act.
SARA TITLE III (Applicable) Applicable.
We believe the information contained herein is current and accurate as of this date of this Material Safety Data Sheet. Since the use of this information and these opinions and the
conditions of use of this product are not under the control of ADHESIVE R&D庐, Inc. or it鈥檚 agents or distributors, it is the user鈥檚 obligation to determine the conditions of safe use of
this product. The buyer should conduct its own tests of this product before use to determine proper preparation technique and suitability for proposed application. ADHESIVE R&D庐,
Inc. warrants that the product conforms with ADHESIVE R&D庐鈥檚 written specifications, and is free from defects and disclaims all other warranties, expressed or implied and is
not responsible for loss claim of damages resulting from the use of it鈥檚 products. Rev 01/03
|