Material Safety Data Sheet
Renew Silicone OO-50 MSDS No. 898
Date Of Preparation: October 11, 2007 Revision: 0000
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: Renew Silicone OO-50 Part A
General Use: Silicone Elastomer
Manufacturer: 95 W. Main Street, Suite 5117, Chester, NJ 07930
Phone (888) 765-9835
Emergency Contact: Chem-Tel
Domestic 800-255-3924
International 813-248-0585
Section 2 - Composition / Information on Ingredients
Component CAS ACGIH TWA Exposure Limits Weight
Number OSHA PEL Percent
(%)
Polyorganosiloxanes Mixed Not Established Not Established 75-85
112926-00-8 10 mg/m3 (as dust) 20 mg/m3 (as dust)
Silica, Amorphous 20-25
Platinum-Siloxane Complex 73018-55-0 Not Established Not Established 0.1
Section 3 - Hazards Identification
HMIS
Potential Health Effects 2
H
1
F
1
R
Primary Entry Routes: Dermal
Acute Effects Inhalation: This is a viscous fluid that does not easily form a mist or vapor and,
therefore, inhalation hazards are minimal.
Eye: Similar silicone fluids are non-irritating to eyes. A slight transient irritation is possible.
Skin: Similar silicone fluids are non-irritating to intact and abraded skin.
Ingestion: Animal tests for similar silicone fluids suggest very low acute oral toxicity.
Carcinogenicity: IARC, NTP, and OSHA do not list any components of this product as a
carcinogen.
Medical Conditions Aggravated by Long-Term Exposure: No Data Found
Section 4 - First Aid Measures
Inhalation: Remove source(s) of contamination and move victim to fresh air. Contact physician
immediately.
Eye Contact: Flush eyes with plenty of water. If irritation persists, seek medical attention.
Skin Contact: In case of skin contact, wash thoroughly with soap and water; remove contaminated
clothing and launder before reuse; seek medical attention if rash develops.
Ingestion: Do not induce vomiting unless instructed by a physician. Contact physician
immediately
After first aid, get appropriate in-plant, paramedic, or community medical support.
MSDS No. 898 Revision: 0000
Section 5 - Fire-Fighting Measures
Flash Point: >300 掳F
Flash Point Method: PMCC NFPA
LEL: Not Established
1
UEL: Not Established
1
2
Flammability Classification: Non-Flammable
鈥?
Extinguishing Media: Dry Chemical, Carbon Dioxide, and Foam
Unusual Fire or Explosion Hazards: None
Fire-Fighting Instructions: Fire fighters should wear self-contained breathing apparatus.
Do not release runoff from fire control methods to sewers or waterways.
Fire-Fighting Equipment: Because fire may produce toxic thermal decomposition products, wear
a self-contained breathing apparatus (SCBA) with a full face piece operated in pressure-demand
or positive-pressure mode.
Section 6 - Accidental Release Measures
Spill /Leak Procedures: Dike and contain spill; absorb or scrape up excess into suitable container
for disposal. Stop or reduce discharge if it can be done safely.
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Section 7 - Handling and Storage
Handling Precautions: Minimize breathing of vapors and avoid prolonged or repeated contact
with skin. Wear proper protective equipment. Use good general housekeeping procedures.
Storage Requirements: Store in cool dry, well-ventilated area.
Section 8 - Exposure Controls / Personal Protection
Engineering Controls:
Ventilation: Provide general or local exhaust ventilation systems to maintain airborne
concentrations below OSHA PELs (Sec. 2). Local exhaust ventilation is preferred because it
prevents contaminant dispersion into the work area by controlling it at its source.
Administrative Controls:
Protective Clothing/Equipment: Wear chemically protective gloves. Wear protective eyeglasses
per OSHA eye and face protection regulations (29 CFR 1910.133). Contact lenses are not eye
protective devices. Appropriate eye protection must be worn instead of, or in conjunction with
contact lenses.
Comments: Never eat, drink, or smoke in work areas. Practice good personal hygiene after using
this material, especially before eating, drinking, smoking, using the toilet, or applying cosmetics
Page 2
MSDS No. 898 Revision: 0000
Section 9 - Physical and Chemical Properties
Physical State: Viscous Liquid Water Solubility: Insoluble
Appearance : Off White viscous liquid Boiling Point: None (Polymeric Resin)
Odor : Sweet odor % Volatile: Nil
Vapor Pressure: None (Polymeric Resin) Freezing/Melting Point: None (Polymeric
Vapor Density (Air=1): >1 Resin)
Viscosity: 100 poise
Specific Gravity (H2O=1, at 4 掳C): 1.07
Evaporation Rate: Not Applicable
Section 10 - Stability and Reactivity
Stability: This product is stable at room temperature in closed containers under normal storage and
handling conditions.
Polymerization: Hazardous polymerization can not occur.
Chemical Incompatibilities: Strong bases, and acids.
Hazardous Decomposition Products: Silica, carbon monoxide and carbon dioxide
Section 11- Toxicological Information
Carcinogenicity: None Determined
Eye Effects: Irritation
Mutagenicity: None Determined
Skin Effects: Irritation
Teratogenicity: None Determined
Section 12 - Ecological Information
None Established
Section 13 - Disposal Considerations
Disposal: Must be disposed of in accordance with applicable Federal, state and local regulations.
Section 14 - Transport Information
DOT IATA IMDG
Not Regulated Not Regulated Not Regulated
Section 15 - Regulatory Information
EPA Regulations:
RCRA Hazardous Waste Number: Not listed (40 CFR 261.33)
CERCLA Hazardous Substance (40 CFR 302.4) listed specific per RCRA, Sec. 3001; CWA, Sec.
311 (b)(4); CWA, Sec. 307(a), CAA, Sec. 112: None
SARA Toxic Chemical (40 CFR 372.65): None
SARA EHS (Extremely Hazardous Substance) (40 CFR 355): None
Page 3
MSDS No. 898 Revision: 0000
Section 15 - Regulatory Information (continued)
This product does not contain chemicals that are subject to release reporting requirements under
section 313 of SARA Title III.
TSCA Inventory Status (40 CFR710): All components of this formulation are listed in the TSCA
Inventory.
State Regulations:
California Proposition 65: This product does not contain any chemical, which has been identified
by the state of California to cause cancer, birth defects or other reproductive harm.
Massachusetts and Washington Right To Know, Substance List:
Chemical Name CAS # % by Weight
Silica, Amphorus 112926-00-8 25 Max.
Section 16 - Other Information
Prepared By: The Safety Department of Renew
Disclaimer: The information contained in this MSDS is considered accurate as of the version date.
However, no warranty is expressed or implied regarding the accuracy of the data. Since the use of
this product is not within the control of Renew, it is the user鈥檚 obligation to determine the suitability
of the product for its intended application and assumes all risk and liability for its safe use.
Page 4
Material Safety Data Sheet
Renew Silicone OO-50 MSDS No. 898
Date Of Preparation: October 11, 2007 Revision: 0000
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: Renew Silicone OO-50 Part B
General Use: Silicone Elastomer
Manufacturer: 95 W. Main Street, Suite 5117, Chester, NJ 07930
Phone (888) 765-9835
Emergency Contact: Chem-Tel
Domestic 800-255-3924
International 813-248-0585
Section 2 - Composition / Information on Ingredients
Component CAS Number ACGIH TWA Exposure Limits Weight
OSHA PEL Percent
(%)
Polyorganosiloxanes Mixed Not Established Not Established 65-70
10 mg/m3 (as dust) 20 mg/m3 (as dust)
Silica, Amorphous 112926-00-8 20-25
Section 3 - Hazards Identification
HMIS
Potential Health Effects 1
H
1
F
1
R
Primary Entry Routes: Dermal
Acute Effects Inhalation: This is a viscous fluid that does not easily form a mist or vapor and,
therefore, inhalation hazards are minimal.
Eye: Similar silicone fluids are non-irritating to eyes. A slight transient irritation is possible.
Skin: Similar silicone fluids are non-irritating to intact and abraded skin.
Ingestion: Animal tests for similar silicone fluids suggest very low acute oral toxicity.
Carcinogenicity: IARC, NTP, and OSHA do not list any components of this product as a
carcinogen.
Medical Conditions Aggravated by Long-Term Exposure: No Data Found
Section 4 - First Aid Measures
Inhalation: Remove source(s) of contamination and move victim to fresh air. Contact physician
immediately.
Eye Contact: Flush eyes with plenty of water. If irritation persists, seek medical attention.
Skin Contact: In case of skin contact, wash thoroughly with soap and water; remove contaminated
clothing and launder before reuse; seek medical attention if rash develops.
Ingestion: Do not induce vomiting unless instructed by a physician. Contact physician
immediately
After first aid, get appropriate in-plant, paramedic, or community medical support.
MSDS No. 898 Revision: 0000
Section 5 - Fire-Fighting Measures
Flash Point: >300 掳F
N FPA
Flash Point Method: PMCC
LEL: Not Established
1
UEL: Not Established
1
1
Flammability Classification: Non-Flammable 鈥?
Extinguishing Media: Dry Chemical, Carbon Dioxide, and Foam
Unusual Fire or Explosion Hazards: None
Fire-Fighting Instructions: Fire fighters should wear self-contained breathing apparatus. Do not
release runoff from fire control methods to sewers or waterways.
Fire-Fighting Equipment: Because fire may produce toxic thermal decomposition products, wear
a self-contained breathing apparatus (SCBA) with a full face piece operated in pressure-demand
or positive-pressure mode.
Section 6 - Accidental Release Measures
Spill /Leak Procedures: Dike and contain spill; absorb or scrape up excess into suitable container
for disposal. Stop or reduce discharge if it can be done safely.
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Section 7 - Handling and Storage
Handling Precautions: Minimize breathing of vapors and avoid prolonged or repeated contact
with skin. Wear proper protective equipment. Use good general housekeeping procedures.
Storage Requirements: Store in cool dry, well-ventilated area.
Section 8 - Exposure Controls / Personal Protection
Engineering Controls:
Ventilation: Provide general or local exhaust ventilation systems to maintain airborne
concentrations below OSHA PELs (Sec. 2). Local exhaust ventilation is preferred because it
prevents contaminant dispersion into the work area by controlling it at its source.
Administrative Controls:
Protective Clothing/Equipment: Wear chemically protective gloves. Wear protective eyeglasses
per OSHA eye and face protection regulations (29 CFR 1910.133). Contact lenses are not eye
protective devices. Appropriate eye protection must be worn instead of, or in conjunction with
contact lenses.
Comments: Never eat, drink, or smoke in work areas. Practice good personal hygiene after using
this material, especially before eating, drinking, smoking, using the toilet, or applying cosmetics
Page 6
MSDS No. 898 Revision: 0000
Section 9 - Physical and Chemical Properties
Physical State: Viscous Liquid Water Solubility: Insoluble
Appearance : Off White viscous liquid Boiling Point: None (Polymeric Resin)
Odor : Sweet odor % Volatile: Nil
Vapor Pressure: None (Polymeric Resin) Freezing/Melting Point: None (Polymeric
Vapor Density (Air=1): >1 Resin)
Viscosity: 100 poise
Specific Gravity (H2O=1, at 4 掳C): 1.07
Evaporation Rate: Not Applicable
Section 10 - Stability and Reactivity
Stability: This product is stable at room temperature in closed containers under normal storage and
handling conditions.
Polymerization: Hazardous polymerization can not occur.
Chemical Incompatibilities: Strong bases, and acids.
Hazardous Decomposition Products: Silica, carbon monoxide and carbon dioxide
Section 11- Toxicological Information
Carcinogenicity: None Determined
Eye Effects: Irritation
Mutagenicity: None Determined
Skin Effects: Irritation
Teratogenicity: None Determined
Section 12 - Ecological Information
None Established
Section 13 - Disposal Considerations
Disposal: Must be disposed of in accordance with applicable Federal, state and local regulations.
Section 14 - Transport Information
DOT IATA IMDG
Not Regulated Not Regulated Not Regulated
Section 15 - Regulatory Information
EPA Regulations:
RCRA Hazardous Waste Number: Not listed (40 CFR 261.33)
CERCLA Hazardous Substance (40 CFR 302.4) listed specific per RCRA, Sec. 3001; CWA, Sec.
311 (b)(4); CWA, Sec. 307(a), CAA, Sec. 112: None
SARA Toxic Chemical (40 CFR 372.65): None
SARA EHS (Extremely Hazardous Substance) (40 CFR 355): None
Page 7
MSDS No. 898 Revision: 0000
Section 15 - Regulatory Information (continued)
This product does not contain chemicals that are subject to release reporting requirements under
section 313 of SARA Title III.
TSCA Inventory Status (40 CFR710): All components of this formulation are listed in the TSCA
Inventory.
State Regulations:
California Proposition 65: This product does not contain any chemical, which has been identified
by the state of California to cause cancer, birth defects or other reproductive harm.
Massachusetts and Washington Right To Know, Substance List:
Chemical Name CAS # % by Weight
Silica, Amphorus 112926-00-8 25 Max.
Section 16 - Other Information
Prepared By: The Safety Department of Renew
Disclaimer: The information contained in this MSDS is considered accurate as of the version date.
However, no warranty is expressed or implied regarding the accuracy of the data. Since the use of
this product is not within the control of Renew, it is the user鈥檚 obligation to determine the suitability
of the product for its intended application and assumes all risk and liability for its safe use.
Page 8
|