Material Safety Data Sheet
Renew Replicator Release MSDS No. 842
Date Of Preparation: February 15, 2006 Revision: 0000
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: Renew Replicator Release
General Use: Silicone Elastomer
Manufacturer: 95 W. Main Street, Suite 511, Chester, NJ 07930
Phone (888) 765-9835
Emergency Contact: Chem-Tel
Domestic 800-255-3924
International 813-248-0585
Section 2 - Composition / Information on Ingredients
Component ACGIH TLV Exposure Limits Weight Percent
OSHA PEL (%)
New Jersey Trade Secret None Established None Established 100
#221290880-5052P
Section 3 - Hazards Identification
Acute Effects
Inhalation: Unknown
Eye: Eye Contact with liquid may cause mild irritation.
Ingestion: If swallowed symptoms may include: gastrointestinal irritation such as, nausea,
vomiting and diarrhea.
Carcinogenicity: This product contains no components listed as carcinogenic by IARC, NTP, and
OSHA 1910(Z).
Section 4 - First Aid Measures
Inhalation: N/A. HMIS
0
H
Eye Contact: Flush eyes with plenty of water. If irritation persists, seek medical 1
F
attention. 0
R
Ingestion: Do not induce vomiting. Seek medical attention immediately.
Section 5 - Fire-Fighting Measures
Flash Point: None NFPA
Flash Point Method: None 1
Flammability Classification: None 0
0
鈥?
Extinguishing Media: Water Fog, Dry Chemical, and Carbon Dioxide Foam
Unusual Fire or Explosion Hazards: None
Fire-Fighting Instructions: Fire fighters should wear self-contained breathing apparatus. Do not
release runoff from fire control methods to sewers or waterways.
Fire-Fighting Equipment: Because fire may produce toxic thermal decomposition products, wear
a self-contained breathing apparatus (SCBA) with a full facepiece operated in pressure-demand or
positive-pressure mode.
MSDS No. 842 Revision: 0000
Section 6 - Accidental Release Measures
Spill /Leak Procedures: Dike larger spills to minimize the contaminated area and facilitate
salvage or disposal. Avoid run-off into storm sewers and ditches, which may lead to natural
waterways. Material should be recovered, if possible or collected by absorbent materials such as
dry clay, sand or sawdust.
Section 7 - Handling and Storage
Storage Requirements: Store in cool dry, well-ventilated area away from all sources of ignition.
Section 8 - Exposure Controls / Personal Protection
Engineering Controls:
Ventilation: Provide adequate ventilation it at its source.
Safety Stations: Make emergency eyewash stations, safety/quick-drench showers, and washing
facilities available in work area.
Comments: Never eat, drink, or smoke in work areas. Practice good personal hygiene after using
this material, especially before eating, drinking, smoking, using the toilet, or applying cosmetics.
Section 9 - Physical and Chemical Properties
Product Form: Cream Water Solubility: Insoluble
Appearance and Odor: Pale Yellow, mild odor Boiling Point: None Established
Vapor Pressure: None Established Evaporation Rate None Established
Vapor Density (Air=1): None Established (BuAc=1):
Specific Gravity: 0.90-0.95
Section 10 - Stability and Reactivity
Stability: This product is stable at room temperature.
Polymerization: Hazardous polymerization cannot occur.
.
Section 11- Toxicological Information
None Established
Section 12 - Ecological Information
None Established
Section 13 - Disposal Considerations
Disposal: Contact your supplier or a licensed contractor for detailed recommendations. Follow
applicable Federal, state, and local regulations.
Section 14 - Transport Information
DOT IATA IMDG
Not Regulated Not Regulated Not Regulated
Page 2
MSDS No. 842 Revision: 0000
Section 15 - Regulatory Information
EPA Regulations:
SARA EHS (Extremely Hazardous Substance) (40 CFR 355): None
TSCA Inventory Status (40 CFR710): All components of this formulation are listed in the TSCA
Inventory.
California Proposition 65: This product contains no chemicals, which in the State of California
has found to cause Cancer, birth defects or other reproductive harm
Section 16 - Other Information
Prepared By: The Safety Department of Renew
Disclaimer: The information contained in this MSDS is considered accurate as of the version date.
However, no warranty is expressed or implied regarding the accuracy of the data. Since the use of
this product is not within the control of Renew, it is the user鈥檚 obligation to determine the suitability
of the product for its intended application and assumes all risk and liability for its safe use.
Page 3
|