Search   
MSDS 
:
 Trimethylsilyl Trifluoromethanesulfonate,  99%
CAS 
:
 27607-77-8
SYNONYMS 
:
 Trimethylsilyl Triflate; Trifluoromethanesulfonic Acid Trimethylsilyl     Ester
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 27607-77-8 |Trimethylsilyl Trifluoromethanesulfona| 99% | 248-565-4 |
| |te | | |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: F C
Risk Phrases: 10 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Flammable. Causes burns.Corrosive.

Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns.
Inhalation:
May cause irritation of the respiratory tract with burning pain in
the nose and throat, coughing, wheezing, shortness of breath and
pulmonary edema. Causes chemical burns to the respiratory tract.
Inhalation may be fatal as a result of spasm, inflammation, edema of
the larynx and bronchi, chemical pneumonitis and pulmonary edema.
Vapors may cause dizziness or suffocation.
Chronic:
None

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Flush skin with plenty of water for at
least 15 minutes while removing contaminated clothing and shoes.
Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Never give anything by mouth to an
unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Do NOT use mouth-to-mouth
resuscitation.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Will burn if involved in a fire. Use
water spray to keep fire-exposed containers cool. Containers may
explode in the heat of a fire. Flammable liquid and vapor. Reacts
violently with water. Vapors may be heavier than air. They can
spread along the ground and collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT get water inside
containers. Do NOT use straight streams of water.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. A
vapor suppressing foam may be used to reduce vapors.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Use only in a well-ventilated area.
Ground and bond containers when transferring material. Use
spark-proof tools and explosion proof equipment. Avoid contact with
eyes, skin, and clothing. Empty containers retain product residue,
(liquid and/or vapor), and can be dangerous. Keep container tightly
closed. Keep away from heat, sparks and flame. Avoid ingestion and
inhalation. Discard contaminated shoes. Do not pressurize, cut, weld,
braze, solder, drill, grind, or expose empty containers to heat,
sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Keep container closed when not in use. Store in a tightly
closed container. Keep under a nitrogen blanket. Store in a cool,
dry, well-ventilated area away from incompatible substances.
Flammables-area.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 27607-77-8:
United Kingdom, WEL - TWA: (listed as silica, amorphous): 6 mg/m3
(inhalable dust); 2.4 mg/m3 TWA (respirable dust)
United Kingdom, WEL - STEL: (listed as silica, amorphous): 18 mg/
STEL (inhalable dust); 7.2 mg/m3 STEL (respirable dust)

Russia: (listed as silica, amorphous): 1 mg/m3 TWA

Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear a chemical apron. Wear appropriate protective
clothing to prevent skin exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use. Follow the OSHA
respirator regulations found in 29 CFR 1910.134 or
European Standard EN 149. Use a NIOSH/MSHA or
European Standard EN 149 approved respirator if
exposure limits are exceeded or if irritation or
other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: clear slightly yellow
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 77 deg C @ 80.00mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 25 deg C ( 77.00 deg F)
Explosion Limits, lower: N/A
Explosion Limits, upper: N/A
Decomposition Temperature:
Solubility in water: reacts
Specific Gravity/Density: 1.1500g/cm3
Molecular Formula: C4H9F3O3SSi
Molecular Weight: 222.26

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable at room temperature in closed containers under normal storage
and handling conditions.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat, exposure to
moist air or water.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, oxides of sulfur, carbon dioxide, hydrogen fluoride
gas, silicon dioxide.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 27607-77-8 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Trimethylsilyl Trifluoromethanesulfonate -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****

Other
No information available.

**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.*
Hazard Class: 3 (8)
UN Number: 2924
Packing Group: III
IMO
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.
Hazard Class: 3.3 (8)
UN Number: 2924
Packing Group: III
RID/ADR
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.
Hazard Class: 3
UN Number: 2924
Packing group: III

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: F C
Risk Phrases:
R 10 Flammable.
R 34 Causes burns.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 25 Avoid contact with eyes.
S 33 Take precautionary measures against static
discharges.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 27607-77-8: No information available.
Canada
CAS# 27607-77-8 is listed on Canada's NDSL List.
CAS# 27607-77-8 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 27607-77-8 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 6/12/1998 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Cholesteryl Crotylcarbonate 62637-94-9
Chloroacetonitrile, 98+% 107-14-2
3-Quinuclidinone hydrochloride, 99% (tlc) 1193-65-3
2'-me-2',3',10,11-tetrahydrospiro(5h-diben 35926-76-2
l-Leucine methyl ester hydrochloride, 98% 7517-19-3
3-Methylbenzylamine, 98% 100-81-2
3-Amino-4-methylbenzoic acid, 99% 2458-12-0
Methyl 4-Nitrobutyrate, Tech. 80% 13013-02-0
2,3,4-Trimethoxybenzonitrile, 97% 43020-38-8
1-Phenyl-3-(2-Thiazolyl)-2-Thiourea, 97+% 14901-16-7
Hydrogen fluoride, 37 wt% solution in triethylamine 73602-61-6
Ammonium Sodium Phosphate Tetrahydrate 99% 0-00-1
5,6-Benzoquinoline, 99+% 85-02-9
4-Methoxy-2-nitrophenol, 99+% 1568-70-3
4-Hydroxybenzyl Alcohol, 97% (TLC) 623-05-2
1-(2-Fluorophenyl)piperazine, 97%(GC) 1011-15-0
Hexamethyl dewar benzene, 97% 7641-77-2
Triaza-12-Crown-4, 99% 0-01-1
alpha-Angelicalactone, 98% 591-12-8
3-Acetamidocoumarin 779-30-6
4,6-Dihydroxy-2-Methylpyrimidine, 99% 40497-30-1
Purpurogallin, tech. 569-77-7
2,3-Dimethyl-P-Nitroanisole, 98% 81029-03-0
4-Nitro-p-terphenyl 10355-53-0
2,3-Dimethylcyclohexylamine, mixture of isomers, 99+% 42195-92-6
Epibromohydrin, 98% 3132-64-7
Stearic Anhydride 638-08-4
Ethyl Vinyl Ether, 99% (gc) 109-92-2
Fluoresceinamine Isomer I, 99% (UV-Vis) 3326-34-9
2-Methyl-1,3-cyclohexanedione, 98+% 1193-55-1
(2S,3S)-2-Amino-3-Ethoxybutanoic Acid Hydrochloride, 99+%, (80% e.e.) 0-01-1
Thioflavin t 2390-54-7
Methyl dichloroacetate, 99+% 116-54-1
Trimethylsilyl Trifluoromethanesulfonate, 99% 27607-77-8
3,4-Dihydro-2H-Pyran, 99% 110-87-2
2-Nitrophenyl Disulfide, 95% 1155-00-6
Methylenedi-p-phenyl diisocyanate 101-68-8
1-Bromo-2,3-Dichlorobenzene, 99% 56961-77-4
n-Butyric Anhydride, 99% 106-31-0
2,2',4'-Trichloroacetophenone, 95%, containing up to 10% water, 4252-78-2
10-Nonadecanone, 99% 504-57-4
Hydrogen hexachloroiridate(IV) hexahydrate, approx. 40% Iridium 16941-92-7
3-(3,4,5-Trimethoxyphenyl)Propionic Acid, 98+% 25173-72-2
Tetrodotoxin, Citrate Free 4368-28-9
Acid Green 25 4403-90-1
Coumalic Acid, 97+% 500-05-0
7,8-Benzoquinoline, 97% 230-27-3
1,10-Diaminodecane, 97+% 646-25-3
Inositol, 98+% (HPLC) 87-89-8
Thallium (III) Nitrate Trihydrate, 99.5% 13453-38-8

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net