Search   
MSDS 
:
 3-Amino-2,4-dimethylpentane, 98+%
CAS 
:
 4083-57-2
SYNONYMS 
:
 (Diisopropylmethyl)amine; 1-(1-Methylethyl)-2-Methylpropanamine.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 4083-57-2 |3-Amino-2,4-dimethylpentane | >98 | 223-809-2 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: F C
Risk Phrases: 11 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Highly flammable. Causes burns.Air sensitive.Highly
flammable.Corrosive.

Potential Health Effects
Eye:
Causes eye burns. May cause chemical conjunctivitis and corneal
damage.
Skin:
Causes skin burns. May cause skin rash (in milder cases), and cold
and clammy skin with cyanosis or pale color.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns. May cause perforation of the digestive
tract. May cause systemic effects.
Inhalation:
Causes chemical burns to the respiratory tract. Aspiration may lead
to pulmonary edema. Vapors may cause dizziness or suffocation. May
cause systemic effects.
Chronic:
Effects may be delayed.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Never give anything by mouth to an
unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Do NOT use mouth-to-mouth
resuscitation. If breathing has ceased apply artificial respiration
using oxygen and a suitable mechanical device such as a bag and a
mask.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Use water spray to keep fire-exposed
containers cool. Water may be ineffective. Material is lighter than
water and a fire may be spread by the use of water. Flammable liquid
and vapor. Vapors may be heavier than air. They can spread along
the ground and collect in low or confined areas. Will be easily
ignited by heat, sparks or flame. Containers may explode if exposed
to fire.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. Water may be ineffective. Water may spread
fire. If water is the only media available, use in flooding amounts.
For large fires, use water spray, fog or alcohol-resistant foam. Do
NOT use straight streams of water. Cool containers with flooding
quantities of water until well after fire is out.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Scoop up
with a nonsparking tool, then place into a suitable container for
disposal. Remove all sources of ignition. Provide ventilation. Place
under an inert atmosphere.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Use only in a well-ventilated area. Ground and bond containers when
transferring material. Do not breathe dust, vapor, mist, or gas. Do
not get in eyes, on skin, or on clothing. Empty containers retain
product residue, (liquid and/or vapor), and can be dangerous. Keep
container tightly closed. Keep away from heat, sparks and flame.
Handle under an inert atmosphere. Store protected from air. Discard
contaminated shoes. Do not pressurize, cut, weld, braze, solder,
drill, grind, or expose empty containers to heat, sparks or open
flames.
Storage:
Keep away from heat, sparks, and flame. Keep container closed when
not in use. Store in a cool, dry, well-ventilated area away from
incompatible substances. Flammables-area. Do not expose to air.
Store under an inert atmosphere.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 4083-57-2:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: clear, colorless
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: 0.8 MPA 20.00 deg C
Boiling Point: 132 deg C @ 760.00mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: 390 deg C ( 734.00 deg F)
Flash Point: 20 deg C ( 68.00 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: +/- 12 G/L (20C)
Specific Gravity/Density: .7760g/cm3
Molecular Formula: C7H17N
Molecular Weight: 115.22

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, exposure to air, excess
heat, strong oxidants.
Incompatibilities with Other Materials:
Air, strong acids, strong bases, strong oxidizing agents.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, irritating and toxic fumes and
gases, carbon dioxide, nitrogen.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 4083-57-2 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
3-Amino-2,4-dimethylpentane -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: AMINES, FLAMMABLE, CORROSIVE, N.O.S.*
Hazard Class: 3 (8)
UN Number: 2733
Packing Group: II
IMO
Shipping Name: AMINES, FLAMMABLE, CORROSIVE, N.O.S.
Hazard Class: 3.2 (8)
UN Number: 2733
Packing Group: II
RID/ADR
Shipping Name: AMINES, FLAMMABLE, CORROSIVE, N.O.S.
Hazard Class: 3
UN Number: 2733
Packing group: II

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: F C
Risk Phrases:
R 11 Highly flammable.
R 34 Causes burns.
Safety Phrases:
S 16 Keep away from sources of ignition - No
smoking.
S 23 Do not inhale gas/fumes/vapour/spray.
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 4083-57-2: No information available.
Canada
CAS# 4083-57-2 is listed on Canada's NDSL List.
CAS# 4083-57-2 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 4083-57-2 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 9/02/1997 Revision #7 Date: 7/22/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Antimony Silicate (Tungsten Doped) 1314-35-8
Beryllium atomic absorption standard solution, 1mg/ml Be in 2% HNO3 7440-41-7
Ammonium Standard, 1000ppm (as N) 7732-18-5
1-Bromopropane, 99% 106-94-5
Thallium Atomic Absorption Standard Solution, 1mg.ml Tl in 2% HNO3 7440-28-0
1,4-Dioxane, Reagent ACS 123-91-1
GASAB 0-01-1
Nicotine Solution, Cigarette 0-01-1
1,6-Heptadien-4-ol, 97% 2883-45-6
Carbol Fuchsin 108-95-2
(S)-2-Amino-3-Methoxypropanoic Acid, 98% 32620-11-4
(R)-(-)-5-Hydroxymethyl-2-Pyrroldinone 66673-40-3
(S)-(+)-5-Triloxymethyl-2-Pyrrolidinone 105526-85-0
N,N-Didecyl-1-Decanamine (Pract) (Isomeric Mixture) 1070-01-5
R-(+)-3-Pyrrolidinol 2799-21-5
Ruthenium atomic absorption standard solution, 1 mg/ml ru in 10% hcl
Isophthalaldehyde, 99% 626-19-7
3-(Methylthio)propionaldehyde, 95% (GC) 3268-49-3
3-Nitropropionic acid, 99% 504-88-1
Chromium standard metal solution in 2% nitric acid 7440-47-3
Cobalt Chloride 7646-79-9
Arsenic standard metal solution, 1000 ppm in 2% HNO3 1327-53-3
n-(3-Bromopropyl)-phthalimide 5460-29-7
2-Hydroxymethyl-1,4-Benzodioxan, 98%(GC) 3663-82-9
Cyclohexanebutyric acid, 99% 4441-63-8
ICP Standard Metal Solution in Hydrochloric Acid 0-00-0
Arsenic standard metal solution, 10000 ppm in 5% HNO3 1327-53-3
2-Methyl-3-Methoxypyrazine, 70-90%, Balance 10-30% 63450-30-6
CRANCO 67-64-1
2,4'-Dibromoacetophenone, 98% 99-73-0
2,3-Diaminopropionic Acid Hydrobromide 98 % 18635-45-5
Matrix 1 7732-18-5
Matrix 2 7664-39-3
Matrix 3 7664-39-3
Beryllium acetate 19049-40-2
Hafnium oxychloride octahydrate 13759-17-6
Ammonium Hexafluorotantalate 33380-11-9
Ammonium Tetraborate 0-01-1
3-Amino-2,4-dimethylpentane, 98+% 4083-57-2
3-Bromo-4-Fluorobenzonitrile, 98% 79630-23-2
Sodium dichromate 10588-01-9
2,4-Dinitrofluorobenzene 70-34-8
Phenylmalonic acid, 99% 2613-89-0
Carbonylbis-(triphenylphosphine)-rhodium (I) chloride 13938-94-8
2,2'-Methylenebisbenzothiazole, 97% 1945-78-4
Chromosulfuric acid 7664-93-9
Lead (II) Hydroxyacetate 0-01-1
Ethyl 3,4,5-Trimethoxybenzoylacetate
Hydrofluoric Acid (Hydrogen Fluoride, liquefied) 7664-39-3
Lactic acid, reagent ACS 50-21-5

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net