**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 546-68-9 |Titanium(IV) isopropoxide | > 98 | 208-909-6 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: None Listed.
Risk Phrases: 10
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable.Moisture sensitive.
Potential Health Effects
Eye:
May cause eye irritation.
Skin:
May cause irritation and dermatitis.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. Ingestion of large amounts may cause CNS depression.
Inhalation:
May cause respiratory tract irritation.
Chronic:
Effects may be delayed.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Never give anything by mouth to an
unconscious person. Get medical aid.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid. Do NOT use mouth-to-mouth
resuscitation.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Will burn if involved in a fire. Use
water spray to keep fire-exposed containers cool. Containers may
explode in the heat of a fire. Flammable liquid and vapor. Vapors
may be heavier than air. They can spread along the ground and
collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Water may be ineffective. Do NOT get water
inside containers. Do NOT use straight streams of water. Cool
containers with flooding quantities of water until well after fire is
out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Use water spray to dilute spill to
a non-flammable mixture. Avoid runoff into storm sewers and ditches
which lead to waterways. Remove all sources of ignition. Use a
spark-proof tool. Do not get water inside containers. A vapor
suppressing foam may be used to reduce vapors.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Use only in a well-ventilated area.
Ground and bond containers when transferring material. Use
spark-proof tools and explosion proof equipment. Avoid contact with
eyes, skin, and clothing. Empty containers retain product residue,
(liquid and/or vapor), and can be dangerous. Keep container tightly
closed. Keep away from heat, sparks and flame. Avoid ingestion and
inhalation. Do not pressurize, cut, weld, braze, solder, drill,
grind, or expose empty containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a cool, dry, well-ventilated area away from
incompatible substances. Keep away from water. Flammables-area. Keep
containers tightly closed. Store protected from moisture.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 546-68-9:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: light yellow
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: 4.3 cP 25 deg C
Boiling Point: 240 deg C @ 760 mm Hg
Freezing/Melting Point: 18 - 20 deg C
Autoignition Temperature: Not applicable.
Flash Point: 46 deg C ( 114.80 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: Decomposes rapidly in water.
Specific Gravity/Density: .950 g/ml
Molecular Formula: C12H28O4Ti
Molecular Weight: 284.26
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures. Substance is readily
hydrolyzed. Isopropanol is susceptible to autoxidation and therefore
should be classified as peroxidizable.
Conditions to Avoid:
Ignition sources, excess heat, exposure to moist air or water.
Incompatibilities with Other Materials:
Anhydrous hydrazine, strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, carbon dioxide, titanium/titanium oxides.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 546-68-9: NT8060000
LD50/LC50:
CAS# 546-68-9: Draize test, rabbit, eye: 20 mg/24H Moderate; Draize
test, rabbit, skin: 500 mg/24H Mild; Oral, rat: LD50 = 7460 uL/kg;
Skin, rabbit: LD50 = >16 mL/kg.
Not available.
Carcinogenicity:
Titanium(IV) isopropoxide -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: FLAMMABLE LIQUID, N.O.S.*
Hazard Class: 3
UN Number: 1993
Packing Group: III
IMO
Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Class: 3.3
UN Number: 1993
Packing Group: III
RID/ADR
Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Class: 3
UN Number: 1993
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: Not available.
Risk Phrases:
R 10 Flammable.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 33 Take precautionary measures against static
discharges.
WGK (Water Danger/Protection)
CAS# 546-68-9: No information available.
Canada
CAS# 546-68-9 is listed on Canada's DSL List.
CAS# 546-68-9 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 546-68-9 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 11/05/1997 Revision #6 Date: 8/11/2004
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Tropylium Hexafluorophosphate
| 29663-54-5 |
|
3-(4-Cyanobenzoyl)-5,7-Dimethoxycoumarin
| 83179-55-9 |
|
Adenine-9-Beta-D-Arabinofuranoside- 5'-Monophosphate, 98%
| 29984-33-6 |
|
4-Tert-Butylaniline, 99%
| 769-92-6 |
|
4,4'-Dicyanobibenzyl
| |
|
Isoquinoline, 99% (GC)
| 119-65-3 |
|
(2-Naphthoxy)Acetic Acid, N-Hydroxysuccinimide Ester, 98%
| 81012-92-2 |
|
Pentafluorophenylhydrazine, 97%
| 828-73-9 |
|
Diphenyl Phosphate, 99%
| 838-85-7 |
|
Manganese(II) bromide tetrahydrate, 98%
| 10031-20-6 |
|
Sulfur trioxide, stabilized, 99%
| 7446-11-9 |
|
epsilon-Caprolactam
| 105-60-2 |
|
2-Bromo-1-Phenylpropane, 98%
| 2114-39-8 |
|
1,1-Bis(Methylseleno)-Ethane
| 56051-04-8 |
|
4-Chloro-2-methylthiopyrimidine, 98%
| 49844-90-8 |
|
4-Cyanobenzoic Acid, 99%
| 619-65-8 |
|
2,2'-Diaminobibenzyl, 96%
| 0-00-1 |
|
(-)-Dihydrocarvyl acetate, mixture of isomers, 99%
| 20777-49-5 |
|
Cyclobutanecarboxylic Acid Chloride, 99%
| 5006-22-4 |
|
4-Methoxybenzylisothiocyanate
| 3694-57-3 |
|
Bis(MSB), scintillation grade, 99.5%
| 13280-61-0 |
|
1-Octene, 97%
| 111-66-0 |
|
Bromoacetaldehyde dimethyl acetal, 97%, stabilized with 0.2%
| 7252-83-7 |
|
d-Histidine hydrochloride monohydrate 99%
| 6341-24-8 |
|
Pimelic acid, 98%
| 111-16-0 |
|
Trans-Beta-Hydromuconic Acid, 98%
| 4436-74-2 |
|
Nickel(ii) acetylacetonate dihydrate, 99+% (titr.)
| 3264-82-2 |
|
Ethyl Allophanate
| 626-36-8 |
|
2,6-Dimethylpyrazine, ca 96% (nmr), balanc e 2,5-isomer
| 108-50-9 |
|
(1,3-Dioxolan-2-ylmethyl)triphenyl phosphonium bromide, 98%
| 52509-14-5 |
|
3,3'-Thiodipropanol, 98%
| 10595-09-2 |
|
2-Imidazolidinethione, paraffinic oil coated powder
| 96-45-7 |
|
Coumarin 7, Laser Grade, 99% (UV-Vis)
| 27425-55-4 |
|
Bemegride, 99+%
| 64-65-3 |
|
DL-3(Methylthio)-2-Butanone 99%
| 53475-15-3 |
|
Methyl (trimethylsilyl)acetate, 98%
| 2916-76-9 |
|
3-Methylindole, 98%
| 83-34-1 |
|
Titanium(IV) isopropoxide, 98+%
| 546-68-9 |
|
2-Hydroxy-4,5-Dimethylacetophenone, 98%
| 36436-65-4 |
|
Allyl sulfide, 97%
| 592-88-1 |
|
Dehydroacetic acid, 98%
| 520-26-3 |
|
Lactulose, 50 Wt% Solution in Water
| 4618-18-2 |
|
Ethylene/propylene copolymer, low molecular weight
| 9010-79-1 |
|
D-(+)-Altrose, 99%
| 1990-29-0 |
|
Ftorafur, 99%
| 17902-23-7 |
|
L(-)-Perillaldehyde, 90% (Titr.)
| 18031-40-8 |
|
3-Amino-5-Methylisoxazole, 98+%
| 1072-67-9 |
|
Yttrium atomic absorption standard solution, 1 mg/ml Y in 2% HNO3
| 7440-65-5 |
|
1,6-Dibromo-2-Naphthol, 99%
| 16239-18-2 |
|
4,4'-Dimethoxytrityl chloride 98%
| 40615-36-9 |
|
|