**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 6180-99-0 |Tributyltin deuteride | 96 | unlisted |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: T N
Risk Phrases: 10 21 25 36/38 48/23/25 50/53
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Harmful in contact with skin. Toxic if swallowed.
Irritating to eyes and skin. Toxic : danger of serious damage to
health by prolonged exposure through inhalation and if swallowed.
Very toxic to aquatic organisms, may cause long-term adverse effects
in the aquatic environment.Moisture sensitive.Air sensitive.
Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation. Harmful if absorbed through the skin.
Ingestion:
Harmful if swallowed. May cause irritation of the digestive tract.
Inhalation:
Harmful if inhaled. Causes respiratory tract irritation.
Chronic:
The critical effect of tributyltin compounds in rats is on the
immune system (ACGIH 7th Edition Documentation of the TLVs).
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Antidote:
None reported.
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. Use water
spray to keep fire-exposed containers cool. Containers may explode
in the heat of a fire. Flammable liquid and vapor. Vapors may be
heavier than air. They can spread along the ground and collect in
low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT get water inside
containers. Do NOT use straight streams of water.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Remove all sources of ignition.
Use a spark-proof tool. Provide ventilation.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Ground and bond containers when transferring
material. Use spark-proof tools and explosion proof equipment. Avoid
contact with eyes, skin, and clothing. Empty containers retain
product residue, (liquid and/or vapor), and can be dangerous. Do not
pressurize, cut, weld, braze, solder, drill, grind, or expose empty
containers to heat, sparks or open flames. Use only with adequate
ventilation. Keep away from heat, sparks and flame. Avoid breathing
vapor or mist.
Storage:
Keep away from sources of ignition. Flammables-area. Keep
refrigerated. (Store below 4C/39F.) Do not expose to air. Store
protected from moisture. Store under an inert atmosphere.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use process enclosure, local exhaust ventilation, or other
engineering controls to control airborne levels below recommended
exposure limits. Facilities storing or utilizing this material should
be equipped with an eyewash facility and a safety shower.
Exposure Limits
CAS# 6180-99-0:
United Kingdom, WEL - TWA: (listed as tin organic compounds): 0.1
mg/m3 TWA (except cyhexatin, as Sn)
United Kingdom, WEL - STEL: (listed as tin organic compounds): 0.
mg/m3 STEL (except cyhexatin, as Sn)
United States OSHA: 0.1 mg/m3 TWA (as Sn) (listed under Tin orga
compounds).
Belgium - TWA: (listed as tin organic compounds): 0.1 mg/m3 VLE (
Sn)
Belgium - STEL: (listed as tin organic compounds): 0.2 mg/m3 VLE
Sn)
France - VME: (listed as tin organic compounds): 0.1 mg/m3 VME (a
Sn)
France - VLE: (listed as tin organic compounds): 0.2 mg/m3 VLE (a
Sn)
Germany: (listed as tin organic compounds): 0.1 mg/m3 VME (as Sn)
Germany: (listed as tin organic compounds): Skin absorber
Malaysia: (listed as tin organic compounds): 0.1 mg/m3 TWA (as Sn
Netherlands: (listed as tin organic compounds): 0.2 mg/m3 STEL (a
Sn)
Netherlands: (listed as tin organic compounds): 0.1 mg/m3 MAC (as
Spain: (listed as tin organic compounds): 0.1 mg/m3 VLA-ED (as Sn
Spain: (listed as tin organic compounds): 0.2 mg/m3 VLA-EC (as Sn
Personal Protective Equipment
Eyes:
Wear chemical splash goggles.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: colorless to very faint yellow
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 65 deg C @ .60mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 39 deg C ( 102.20 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: 1.08 g/cm3
Molecular Formula: C12H27DSn
Molecular Weight: 292.06
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stability unknown.
Conditions to Avoid:
Ignition sources, moisture, exposure to air, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, carbon dioxide, tin/tin oxides.
Hazardous Polymerization: Has not been reported
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 6180-99-0 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Tributyltin deuteride -
Not listed by ACGIH, IARC, or NTP.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
Other
No information available.
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: FLAMMABLE LIQUID, TOXIC, N.O.S.*
Hazard Class: 3 (6.1)
UN Number: 1992
Packing Group: III
IMO
Shipping Name: FLAMMABLE LIQUID, TOXIC, N.O.S.
Hazard Class: 3.3 (6.1)
UN Number: 1992
Packing Group: III
RID/ADR
Shipping Name: FLAMMABLE LIQUID, TOXIC, N.O.S.
Hazard Class: 3 (6.1)
UN Number: 1992
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: T N
Risk Phrases:
R 10 Flammable.
R 21 Harmful in contact with skin.
R 25 Toxic if swallowed.
R 36/38 Irritating to eyes and skin.
R 48/23/25 Toxic : danger of serious damage to
health by prolonged exposure through inhalation and if
swallowed.
R 50/53 Very toxic to aquatic organisms, may cause
long-term adverse effects in the aquatic environment.
Safety Phrases:
S 35 This material and its container must be
disposed of in a safe way.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
S 60 This material and its container must be
disposed of as hazardous waste.
S 61 Avoid release to the environment. Refer to
special instructions/safety data sheets.
WGK (Water Danger/Protection)
CAS# 6180-99-0: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 6180-99-0 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 6180-99-0 is not listed on the TSCA inventory.
It is for research and development use only.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 4/01/1999 Revision #3 Date: 4/22/2004
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Palladium(ii) trifluoroacetate
| 42196-31-6 |
|
Nitrilotriacetic acid, disodium salt, 99+%
| 15467-20-6 |
|
Tetramethylphosphonium Bromide, 98%
| 4519-28-2 |
|
Zinc trifluoromethanesulfonate, 98%
| 54010-75-2 |
|
Phosphomolybdic acid, ammonium salt hydrate
| 54723-94-3 |
|
Triethylphosphine, 99%
| 554-70-1 |
|
5-Chloro-N-Methyl-2-Nitrobenzenamine, 99%
| 35966-84-8 |
|
Cadmium acetate dihydrate, 98%
| 543-90-8 |
|
(1-Bromoethyl)benzene, 97%
| 585-71-7 |
|
1,2,4-Tribromobenzene
| 615-54-3 |
|
3,5-Dibromo-4-Hydroxybenzoic Acid, 99%
| 3337-62-0 |
|
3,6-Thioxanthenediamine-10,10-Dioxide
| 10215-25-5 |
|
Rubidium Carbonate, 99%
| 584-09-8 |
|
Europium(iii) carbonate hydrate, 99.9%
| 5895-48-7 |
|
Dimethylmercury, 95%
| 593-74-8 |
|
2,5-Dimethyltetrahydrofuran 99% , Mixture of Cis/Trans
| 1003-38-9 |
|
Triphenylantimony dichloride, 99%
| 594-31-0 |
|
Tetraethylgermane, 99%
| 597-63-7 |
|
Zinc Acetate Dihydrate, Reagent ACS, 98+%
| 5970-45-6 |
|
(s)-(-)-1,2-Propanediol di-p-tosylate, 99%
| 60434-71-1 |
|
Lead(II)Acetate Trihydrate, 99.999%
| 6080-56-4 |
|
Lithium Formate Monohydrate, 98%
| 6108-23-2 |
|
Niobium(iv) chloride-tetrahydrofuran complex
| 61247-57-2 |
|
Tributyltin deuteride
| 6180-99-0 |
|
Tri-m-tolylphosphine, 98%
| 6224-63-1 |
|
Chlorotriphenyltin, 95%
| 639-58-7 |
|
Triisopropylphosphine
| 6476-36-4 |
|
bis(Diethylamino)chlorophosphine, 97%
| 685-83-6 |
|
Benzylmagnesium chloride, 2.0 m solution i n tetrahydrofuran
| 6921-34-2 |
|
Calcium Iodide Hydrate, 98%
| 71626-98-7 |
|
Dysprosium, ingot, 99.9%
| 7429-91-6 |
|
Dysprosium, chip, 99.9%
| 7429-91-6 |
|
Lutetium, ingot, 99.9%
| 7439-94-3 |
|
Manganese, powder, -325 mesh, 99+%
| 7439-96-5 |
|
Neodymium, ingot, 99.9%
| 7440-00-8 |
|
Niobium, powder, -60 to -325 mesh, 99.8%
| 7440-03-1 |
|
Niobium, rod, 6.35 mm diam., 99.8%
| 7440-03-1 |
|
Niobium, powder, -325 mesh, 99.8%
| 7440-03-1 |
|
Niobium, wire, 1.0 mm diam., 99.8%
| 7440-03-1 |
|
Palladium on calcium carbonate, unreduced (5% Pd)
| 471-34-1 |
|
Palladium on Barium Sulfate, Reduced (5% Pd)
| 7440-05-3 |
|
Palladium on barium carbonate, reduced (5% pd)
| 7440-05-3 |
|
1-(2-Aminophenyl)Pyrrole, 98+%
| 6025-60-1 |
|
Praseodymium, foil, 0.25 mm thick, 99.9%
| 7440-10-0 |
|
Praseodymium, chip, 99.9%
| 7440-10-0 |
|
Praseodymium, powder, -40 mesh, 99.9%
| 7440-10-0 |
|
Praseodymium, ingot, 99.9%
| 7440-10-0 |
|
Rhenium on carbon (5% re)
| 7440-15-5 |
|
Rhenium, foil, 0.1 mm thick, 99.98%
| 7440-15-5 |
|
Silver, Wire, 0.5 mm Diam., 99.9%
| 7440-22-4 |
|
|