Search   
MSDS 
:
 bis(Diethylamino)chlorophosphine, 97%
CAS 
:
 685-83-6
SYNONYMS 
:
 Bis-(diethylamino)-phosphorochloridite
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 685-83-6 |Bis(diethylamino)chlorophosphine | 97.0 | unlisted |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 14 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Reacts violently with water. Causes burns.Water-reactive.Corrosive.

Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns.
Inhalation:
Causes chemical burns to the respiratory tract.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately. Do NOT allow victim to rub eyes or keep eyes closed.
Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Never give anything by mouth to an
unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If breathing is difficult, give oxygen. Do NOT use
mouth-to-mouth resuscitation. If breathing has ceased apply
artificial respiration using oxygen and a suitable mechanical device
such as a bag and a mask.
Notes to Physician:
Antidote:
None reported.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Water
Reactive. Material will react with water and may release a flammable
and/or toxic gas. May ignite or explode on contact with steam or
moist air.
Extinguishing Media:
Use dry sand or earth to smother fire. DO NOT USE WATER! Contact
professional fire-fighters immediately.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Provide ventilation. Do not expose spill to water.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Do not allow water to get into the container because of violent
reaction. Do not get in eyes, on skin, or on clothing. Keep
container tightly closed. Do not ingest or inhale. Use with adequate
ventilation. Do not allow contact with water. Discard contaminated
shoes. Keep from contact with moist air and steam.
Storage:
Keep container closed when not in use. Store in a cool, dry,
well-ventilated area away from incompatible substances. Keep away
from water. Corrosives area. Keep containers tightly closed.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Use explosion-proof ventilation equipment. Facilities storing or
utilizing this material should be equipped with an eyewash facility
and a safety shower. Use adequate ventilation to keep airborne
concentrations low.
Exposure Limits
CAS# 685-83-6:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to minimize
contact with skin.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use. Follow the OSHA
respirator regulations found in 29 CFR 1910.134 or
European Standard EN 149. Use a NIOSH/MSHA or
European Standard EN 149 approved respirator if
exposure limits are exceeded or if irritation or
other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: yellow
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 55 - 57 deg C @ .20mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 101 deg C ( 213.80 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: 1.0020g/cm3
Molecular Formula: C8H20ClN2P
Molecular Weight: 210.69

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Combines vigorously or explosively with water.
Conditions to Avoid:
Exposure to moist air or water.
Incompatibilities with Other Materials:
Strong oxidizing agents, alcohols, water, active metals, halogens.
Hazardous Decomposition Products:
Hydrogen chloride, phosphine, carbon monoxide, oxides of nitrogen,
oxides of phosphorus, carbon dioxide.
Hazardous Polymerization: Will not occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 685-83-6 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Bis(diethylamino)chlorophosphine -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: CORROSIVE LIQUID, N.O.S.*
Hazard Class: 8
UN Number: 1760
Packing Group: II
IMO
Shipping Name: CORROSIVE LIQUID, N.O.S.
Hazard Class: 8
UN Number: 1760
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE LIQUID, N.O.S.
Hazard Class: 8
UN Number: 1760
Packing group: II

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 14 Reacts violently with water.
R 34 Causes burns.
Safety Phrases:
S 8 Keep container dry.
S 25 Avoid contact with eyes.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 685-83-6: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 685-83-6 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 685-83-6 is not listed on the TSCA inventory.
It is for research and development use only.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 3/22/1999 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Palladium(ii) trifluoroacetate 42196-31-6
Nitrilotriacetic acid, disodium salt, 99+% 15467-20-6
Tetramethylphosphonium Bromide, 98% 4519-28-2
Zinc trifluoromethanesulfonate, 98% 54010-75-2
Phosphomolybdic acid, ammonium salt hydrate 54723-94-3
Triethylphosphine, 99% 554-70-1
5-Chloro-N-Methyl-2-Nitrobenzenamine, 99% 35966-84-8
Cadmium acetate dihydrate, 98% 543-90-8
(1-Bromoethyl)benzene, 97% 585-71-7
1,2,4-Tribromobenzene 615-54-3
3,5-Dibromo-4-Hydroxybenzoic Acid, 99% 3337-62-0
3,6-Thioxanthenediamine-10,10-Dioxide 10215-25-5
Rubidium Carbonate, 99% 584-09-8
Europium(iii) carbonate hydrate, 99.9% 5895-48-7
Dimethylmercury, 95% 593-74-8
2,5-Dimethyltetrahydrofuran 99% , Mixture of Cis/Trans 1003-38-9
Triphenylantimony dichloride, 99% 594-31-0
Tetraethylgermane, 99% 597-63-7
Zinc Acetate Dihydrate, Reagent ACS, 98+% 5970-45-6
(s)-(-)-1,2-Propanediol di-p-tosylate, 99% 60434-71-1
Lead(II)Acetate Trihydrate, 99.999% 6080-56-4
Lithium Formate Monohydrate, 98% 6108-23-2
Niobium(iv) chloride-tetrahydrofuran complex 61247-57-2
Tributyltin deuteride 6180-99-0
Tri-m-tolylphosphine, 98% 6224-63-1
Chlorotriphenyltin, 95% 639-58-7
Triisopropylphosphine 6476-36-4
bis(Diethylamino)chlorophosphine, 97% 685-83-6
Benzylmagnesium chloride, 2.0 m solution i n tetrahydrofuran 6921-34-2
Calcium Iodide Hydrate, 98% 71626-98-7
Dysprosium, ingot, 99.9% 7429-91-6
Dysprosium, chip, 99.9% 7429-91-6
Lutetium, ingot, 99.9% 7439-94-3
Manganese, powder, -325 mesh, 99+% 7439-96-5
Neodymium, ingot, 99.9% 7440-00-8
Niobium, powder, -60 to -325 mesh, 99.8% 7440-03-1
Niobium, rod, 6.35 mm diam., 99.8% 7440-03-1
Niobium, powder, -325 mesh, 99.8% 7440-03-1
Niobium, wire, 1.0 mm diam., 99.8% 7440-03-1
Palladium on calcium carbonate, unreduced (5% Pd) 471-34-1
Palladium on Barium Sulfate, Reduced (5% Pd) 7440-05-3
Palladium on barium carbonate, reduced (5% pd) 7440-05-3
1-(2-Aminophenyl)Pyrrole, 98+% 6025-60-1
Praseodymium, foil, 0.25 mm thick, 99.9% 7440-10-0
Praseodymium, chip, 99.9% 7440-10-0
Praseodymium, powder, -40 mesh, 99.9% 7440-10-0
Praseodymium, ingot, 99.9% 7440-10-0
Rhenium on carbon (5% re) 7440-15-5
Rhenium, foil, 0.1 mm thick, 99.98% 7440-15-5
Silver, Wire, 0.5 mm Diam., 99.9% 7440-22-4

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net