===================== Product Identification =====================
MSDS NAME:EPOXY PAINT (BASE)
NIIN:01-316-6741
Status Code:A
MSDS Number: CLPTF
=== Responsible Party ===
Company:HEMPEL COATINGS USA, INC.
Address:6901 CAVALCADE
City:HOUSTON
State:TX
ZIP:77028
Country:US
Info Phone Num:713-672-6641
Emergency Phone Num:713-672-6641
Preparer's Name:ERNEST CARTER
Chemtrec Ind/Phone:(800)424-9300
CAGE:UO333
=== Contractor Identification ===
Company:HEMPEL COATINGS USA, INC.
Address:6901 CAVALCADE
Box:City:HOUSTON
State:TX
ZIP:77028
Country:US
Phone:713-672-6641
CAGE:UO333
============= Composition/Information on Ingredients =============
Name:EPOXY RESIN (BISPHENOL A DIGLYCIDYL ETHER TYPE)
CAS:25068-38-6
Code:F
RTECS #:CE6880000
Minumum % Wt:45.
Maxumum % Wt:60.
Name:TITANIUM DIOXIDE
CAS:13463-67-7
RTECS #:XR2275000
Minumum % Wt:5.
Maxumum % Wt:10.
OSHA PEL:15 MG/M3
ACGIH TLV:10 MG/M3
Name:TALC
CAS:14807-96-6
RTECS #:WW2710000
Minumum % Wt:30.
Maxumum % Wt:45.
OSHA PEL:SEE TABLE Z-3
ACGIH TLV:2 MG/M3
Name:BENZYL ALCOHOL
CAS:100-51-6
RTECS #:DN3150000
Minumum % Wt:1.
Maxumum % Wt:5.
Name:XYLENE
CAS:1330-20-7
RTECS #:ZE2100000
Minumum % Wt:5.
Maxumum % Wt:10.
ACGIH TLV:434 MG/M3;100 PPM
ACGIH STEL:651 MG/M3;150 PPM
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:ETHYLBENZENE
CAS:100-41-4
RTECS #:DA0700000
Minumum % Wt:1.
Maxumum % Wt:5.
OSHA PEL:435 MG/M3;100 PPM
ACGIH TLV:434 MG/M3;100 PPM
ACGIH STEL:543 MG/M3;125 PPM
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
===================== Hazards Identification =====================
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Effects of Overexposure:INHALATION: IRRITATION OF THE RESPIRATORY TRACT
OR NERVOUS SYSTEM DEPRESSION PRODUCING SUCH AFFECTS AS
GIDDINESS,HEADACHE, DIZZINESS, NAUSEA.AND LOSS OF CONSCIOUSNESS. IF
SEVERE, DEATH MAY OCCUR. EYE : IRRITATION. SKIN:PROLONGED OR
REPEATED LIQUID CONTACT CAN RESULT IN DEFATTING AND DRYING WHICH
MAY RESULT IN IRRITATION AND DERMATITIS. PREEXISTING EYE, SKIN,
RESPIRATORY DISORDERS MAY BE AGGRAVATED BY ANY EXPOSURE TO THIS
PRODUCT. EXERCISE DUE CARE WHEN HANDLING THIS PRODUCT.
======================= First Aid Measures =======================
First Aid:INHALATION: REMOVE VICTIM TO FRESH AIR.AND PROVIDE OXYGEN OR
ARTIFICIAL RESPIRATION IF NEEDED, GET MEDICAL AID. SKIN:REMOVE WITH
WATER. FOLLOW BY WASHING WITH ADDITIONAL SOAP AND WATER. IF
IRRITATION OCCURS, GET MEDICAL AID. EYE: FLUSH WITH PLENTY OF
WATER FOR AT LEAST 15 MINUTES.GET MEDICAL AID. INGESTION: DO NOT
INDUCE VOMITING. PREVENT LIQUID ASPIRATION INTO LUNGS.
===================== Fire Fighting Measures =====================
Flash Point Method:TCC
Flash Point:=25.C, 77.F
Lower Limits:1.0%
Extinguishing Media:FOAM, CO2, DRY CHEMICAL, WATER FOG.
Fire Fighting Procedures:CONTAINERS THAT ARE EXPOSED TO INTENSE HEAT
SHOULD BE COOLED WITH WATER. AVOID SPREADING DURING LIQUID WITH
THE WATER USED FOR COOLING PURPOSES. DO NOT ENTER FIRE AREA WITHOUT
THE PROPER PROTECTION. WEAR SELF CONTAINED BREATHING APPARATUS AND
PROTECTIVE GEAR. FIGHT FIRE FROM A SAFE DISTANCE OR A PROTECTED
LOCATION.
Unusual Fire/Explosion Hazard:KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE
FROM HEAT, ELECTRICAL EQUIPMENT, SPARKS, AND OPEN FLAME. VAPORS MAY
BE HEAVIER THAN AIR AND MAY TRAVEL ALONG THE GROUND BEFORE
IGNITION/FLASHING BACK TO VAPOR SOURCE.
================== Accidental Release Measures ==================
Spill Release Procedures:SHUT OFF AND ELIMINATE ALL IGNITION SOURCES.
KEEP PEOPLE AWAY FROM SPILL. RECOVER ANY FREE PRODUCT. ADD SAND,
EARTH OR OTHER SUITABLE ABSORBENT TO SPILL AREA.MINIMIZE BREATHING
VAPORS AND SKIN CONTACT . VENTILATE CONFINED SPACES. KEEP PRODUCT
OUT OF SEWERS AND PUBLIC WATERS. PLACE ABSORBED MATERIAL IN
PROPERLY SEALED NON-LEAKING CONTAINERS FOR PROPER DISPOSAL.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:THE USE OF RESPIRATORY PROTECTION DEPENDS ON THE
VAPOR CONCENTRATION ABOVE THE TLV-PEL. USE A NIOSH/MSHA APPROVED
CARTRIDGE TYPE PARTICULATE/VAPOR RESPIRATOR OR AIR-SUPPLIED MASK
IN CONFINED AREAS.
Ventilation:LOCAL EXHAUST MUST BE PROVIDED TO KEEP LEL AND TLV-PEL OF
THE HAZARDOUS INGREDIENTS BELOW ACCEPTABLE EXPOSURE LIMITS IN
ACCORDANCE WITH OSHA 29 CFR 1910.
Protective Gloves:SHOULD BE IMPERMEABLE AND MADE OF CHEMICALLY
RESISTANT MATERIAL.
Eye Protection:SAFETY GLASSES, CHEMICAL GOGGLES/FACE SHIELDS
RECOMMENDED.
Other Protective Equipment:USE AS NECESSARY DEPENDING UPON THE METHOD
OF APPLICATION.
Supplemental Safety and Health
================== Physical/Chemical Properties ==================
Boiling Pt:B.P. Text:HI-403.0-LO-242.0-F
Vapor Density:HEAVIER
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NEGLIGIBLE
Appearance and Odor:TYPICAL OF SOLVENTS USED
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
CONTACT WITH OXIDIZING AGENTS.
Stability Condition to Avoid:HEAT, FLAME, SPARKS AND CONTACT WITH
OXIDIZING AGENTS.
Hazardous Decomposition Products:COMBUSTION MAY GENERATE CARBON
MONOXIDE, CARBON DIOXIDE, AND OTHER TOXIC VAPORS FROM ORGANIC
COMPOUNDS.
Conditions to Avoid Polymerization:WILL NOT OCCUR.
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE,
AND LOCAL REGULATIONS.
======================================================================
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|