MATERIAL SAFETY DATA SHEET
1. PRODUCT IDENTIFICATION
Product: PC-125 Rust Inhibitive Primer
Product Code: PC-125
MSDS Date: 06-10-04
2. COMPANY IDENTIFICATION
Acrymax Technologies Inc.
221 Brooke Street
Media, PA 19063
Emergency Phone # 610-566-7473
Information Phone # 800-553-0523
3. INGREDIENTS
# Ingredient CAS Reg. # Weight (%) Vapor Pressure Occupational Exposure
mm Hg @ Temp Limits
ACGIH TLV
1 Hydrous Magnesium Silicate 14807-96-6 10-15 NA 2 mg/m3 Respirable Dust
ACGIH TLV
2 Calcium Strontium Phosphosilicate 66402-68-4 8-12 NA 5 mg/m3 Respirable Dust
10 mg/m3 Total Dust
ACGIH 10 mg/m3 Total
3 Titanium Dioxide 13463-67-7 5-10 NA Dust, 8 hr. TWA
720.00 @ 80oF
4 Aqua Ammonia 7664-41-7 0鈥?5 ACGIH TWA 25 ppm
.000008 @ 68oF
5 Butyl Benzyl Phthalate 85-68-7 0鈥?5 None established
Hydrated Aluminum-Magnesium
6 8031-18-3 0鈥?5 NA None established
Silicate
7 Alkylaryl Polyether 60864-33-7 0鈥?5 NA None established
8 Petroleum Based Defoamer Trade Secret 0鈥?5 NA PEL 5 mg/m3 TWA
Proposition 65 Statement: Certain raw materials used in making this product may contain small amounts of materials as
impurities which are regulated by Propostion 65.
4. PHYSICAL AND CHEMICAL PROPERTIES
Appearance Semi viscous liquid
State Liquid
Odor Characteristic Mild ammonia odor
Vapor Density (Air = 1) Heavier than air
Vapor Pressure No data
Specific Gravity (H2O = 1) 1.25
2500F
Boiling Point
Solubility in Water Non-Soluble
VOC 0.4 lbs/gal. 48 grams/liter
Evaporation Rate Slower than ether
The physical and chemical data given in Section 4 are typical values for this product and are not intended to be product specifications.
5. FIRE AND EXPLOSION HAZARD DATA
340O PMCC
Flash Point
Flammable Limits in Air by Volume Lower: 16.000 Upper: 25.000
Extinguishing agents: Foam, CO2, Dry Chemical
Personal Protective Equipment: As in any fire, wear self-contained breathing apparatus (pressure-demand, NIOSH approved
or equivalent) and full protective gear.
MSDS 鈥? 06/01/04 鈥? Product Code: PC-125 - Page 1 of 3
Unusual Fire and Explosion Hazards: Pressure may build up in tightly closed containers exposed to fire which may result in
rupture. Keep containers cooled with water spray. Vapors may travel a considerable distance to a source of ignition or may
collect in a low area. Sources of ignition include pilot lights, electrical motors, cigarettes, etc.
6. REACTIVITY DATA
Instability: Information not available. Conditions to avoid: Keep from heat or flame, poor ventilation and corrosive
atmospheres.
Hazardous Decomposition Products: There are no known hazardous decomposition products for this material.
Hazardous Polymerization: Product will not undergo hazardous polymerization.
Incompatibility: Avoid contact with the following: Alkaline materials, strong acids and oxidizing materials
7. HEALTH HAZARD DATA
Primary Routes of Exposure: Inhalation - Skin Contact - Eye Contact
Inhalation 鈥? Excessive inhalation of vapors or mist can cause nausea, headache, irritation to the nose, throat, and lungs.
Eye Contact - Material can cause the following: -slightly irritating to the eyes
Skin Contact - Prolonged or repeated skin contact can cause the following: -moderate skin irritation 鈥? reddening
Ingestion - Material is harmful if swallowed. Material can cause the following:-gastrointestinal irritation 鈥? nausea 鈥? vomiting 鈥?
diarrhea
Medical Conditions Generally Aggravated by Exposure - High vapor concentrations (greater than approximately 1000 ppm)
are irritating to the eyes and the repiratory tract, may cause headache and dizziness, are anesthetic, and may have other central
nervous system effects.
8. FIRST AID MEASURES
Inhalation - Move subject to fresh air. If breathing is difficult, give oxygen. Give artificial respiration if breathing has stopped.
Get prompt medical attention.
Eye Contact - IMMEDIATELY flush eyes with a large amount of water for at least 15 minutes. Get prompt medical attention.
Skin Contact - Remove contaminated clothing. Wash affected areas thoroughly with soap and water. Wash contaminated
clothing thoroughly before reuse. If redness, itching or a burning sensation develops, see a physician.
Ingestion - DO NOT induce vomiting. Immediately give 1 or 2 glasses of milk or water to drink and call a physician, hospital
emergency room, or poison control center. If vomiting occurs spontaneously, keep airway clear. Careful gastric lavage may be
indicated. Get medical attention at once.
Note to Physician - No specific antidote, treat symptomatically.
9. ACCIDENTAL RELEASE MEASURES
Personal Protection
Wear compatible, chemically resistant gloves. Wear protective clothing including splash proof goggles and rubber overshoes.
Procedures: Contain spills immediately with inert materials (e.g. sand, earth). If material is spilled in a confined area ventilate
the area well. Keep spectators away. Floor may be slippery; use care to avoid falling. Transfer liquids and solid diking material
to separate suitable containers for recovery or disposal. Keep spills and cleaning runoffs out of municipal sewers and open
bodies of water. Advise authorities if product has entered or may enter sewers or waterways.
10. HANDLING & STORAGE
Storage Conditions: Avoid temperature extremes during storage; ambient temperature preferred. Store in well-ventilated area.
Keep container tightly closed when not in use.
Handling Procedures: Use in well-ventilated areas. Keep containers closed when not in use. Keep away from excessive heat
and open flames. Do not work alone! Keep out of reach of children!
Other: Improper disposal or re-use of this container may be dangerous and illegal. Refer to applicable local, state and federal
regulations.
MSDS 鈥? 06/01/04 鈥? Product Code: PC-125 - Page 2 of 3
11. EXPOSURE CONTROLS 鈥? PERSONAL PROTECTION
Respiratory Protection: A respiratory protection program meeting OSHA 1910.134 and ANSI Z88.2 requirements or
equivalent must be followed whenever workplace conditions warrant a respirator鈥檚 use. None required under normal operation
conditions. Where vapor or mists may occur, wear a MSHA/NIOSH approved (or equivalent) half-mask air-purifying
respirator. Air-purifying respirators should be equipped with NIOSH approved (or equivalent) organic vapor cartridges and N-
95 filters. If oil mist is present. Use R95 or P95 filters.
Eye Protection: Use chemical splash goggles or face shield (ANSI Z87.1 or approved equivalent). Eye protection worn must
be compatible with respiratory protection system employed.
Hand Protection: Chemical-resistant gloves should be worn whenever this material is handled to avoid prolonged or repeated
contact with skin.
Other protection: Use chemically resistant apron or other impervious clothing to avoid prolonged or repeated skin contact.
Engineering Controls (Ventilation): Use local exhaust ventilation with a minimum capture velocity of 100ft/min. (.5 m/sec.)
at the point of vapor evolution. Refer to the current edition of Industrial Ventilation: A Manual of Recommended Practice
published by the American Conference of Governmental Industrial Hygienists for information on the design, installation, use,
and maintenance of exhaust systems.
Work 鈥? Hygienic Practices: Remove contaminated clothing; launder or dry clean before reuse. Wash thoroughly with soap
and water.
12. DISPOSAL CONSIDERATIONS
Procedure: Dispose of in accordance with all local, state, and federal regulations.
13. TRANSPORT INFORMATION
US DOT Hazard Class Paint, Not Regulated
14. OTHER INFORMATION
Category HMIS 鈥? PC-125 Scale
Toxicity 1 4=Extreme
Fire 1 3=High
Reactivity 0 2=Moderate
Special - 1=Slight
0=Insignificant
Prepared by: Acrymax Technologies Inc. 鈥? Technical Department
The information contained herein relates only to the specific material identified. Acrymax Technologies Inc. believes that such
information is accurate and reliable as of the date of this Material Safety Data Sheet, but no representation, guarantee or
warranty, expressed or implied, is made as to the accuracy, reliability, or completeness of the information. Since conditions of
use are out of our control, users assume all risks associated with the use of the material and are advised to confirm in advance
that the information contained in this MSDS is correct, applicable, and suitable to their circumstances. As these are proprietary
formulations, the actual percentages of ingredients have been omitted pursuant to OSHA Federal Hazard Communication
Standard.
MSDS 鈥? 06/01/04 鈥? Product Code: PC-125 - Page 3 of 3
|