MATERIAL SAFETY
DATA SHEET
Prepared to U.S. OSHA, CMA, ANSI and Canadian WHMIS Standards
1. PRODUCT IDENTIFICATION
CHEMICAL NAME; CLASS: ACETYLENE
SYNONYMS: Ethine; Ethyne
CHEMICAL FAMILY: Alkane (hydrocarbon)
FORMULA: C2H2
Document Number: 10002
PRODUCT USE: For chemical synthesis, manufacture of carbon
black, welding, cutting, and for general
analytical or synthetic chemical uses.
MANUFACTURED/SUPPLIED FOR:
ADDRESS: 2700 Post Oak Drive
Houston, TX 77056-8229
EMERGENCY PHONE: CHEMTREC: 1-800-424-9300
BUSINESS PHONE:
General MSDS Information: 1-713/896-2896
Fax on Demand: 1-800/231-1366
2. COMPOSITION and INFORMATION ON INGREDIENTS
CHEMICAL NAME CAS # mole % EXPOSURE LIMITS IN AIR
ACGIH OSHA
TLV STEL PEL STEL IDLH OTHER
ppm ppm ppm ppm ppm
Acetylene 74-86-2 >98-99.6% Simple NE NE NE NE NIOSH REL:
Asphyxiant 2500 ppm,
ceiling
Maximum Impurities <2-.4% None of the trace impurities in this product contribute significantly to the hazards associated
with the product. All hazard information pertinent to this product has been provided in this
Material Safety Data Sheet, per the requirements of the OSHA Hazard Communication
Standard (29 CFR 1910.1200) and State equivalent standards.
NE = Not Established C = Ceiling Limit See Section 16 for Definitions of Terms Used.
NOTE: all WHMIS required information is included. It is located in appropriate sections based on the ANSI Z400.1-1993 format.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 1 OF 8
3. HAZARD IDENTIFICATION
EMERGENCY OVERVIEW: This product is a colorless, flammable gas, with a garlic-like odor, that is dissolved in
acetone. Acetylene poses an extreme fire hazard when accidentally released. The main health hazard
associated with a release of Acetylene is asphyxiation by displacement of oxygen. Acetylene is lighter than air,
and may spread long distances. Distant ignition and flashback are possible. Flame or high temperature
impinging on a localized area of the cylinder of this product can cause the cylinder to rupture violently without
activating the cylinder鈥檚 relief devices. Acetylene is an asphyxiant and presents a significant health hazard by
displacing the oxygen in the atmosphere. Provide adequate fire protection during emergency response situations.
Acetylene may decompose explosively at elevated temperatures and pressures.
SYMPTOMS OF OVER-EXPOSURE BY ROUTE OF
HAZARDOUS MATERIAL INFORMATION
EXPOSURE: The most significant route of over-exposure for this
SYSTEM
product is by inhalation.
HEALTH
INHALATION: Acetylene, at concentration below the LEL of 2.5% 0
(BLUE)
(25000 ppm), is essentially non-toxic. At higher concentrations,
Acetylene has anesthetic effects. Symptoms of over-exposure to
such high concentrations may include drowsiness, dizziness, and
a general feeling of weakness.
FLAMMABILITY 4
(RED)
High concentrations of this gas can cause an oxygen-deficient
environment. It should be noted that before suffocation could
occur, the lower flammability limit of Acetylene in air would be
REACTIVITY
exceeded; possibly causing an oxygen-deficient and explosive (YELLOW) 3
atmosphere. Individuals breathing such an atmosphere may
experience symptoms which include headaches, ringing in ears,
dizziness, drowsiness, unconsciousness, nausea, vomiting, and
PROTECTIVE EQUIPMENT B
depression of all the senses. Under some circumstances of over-
exposure, death may occur. The following effects associated with
various levels of oxygen are as follows: EYES HANDS BODY
RESPIRATORY
CONCENTRATION SYMPTOM OF EXPOSURE
See Section 8
12-16% Oxygen: Breathing and pulse rate increased,
muscular coordination slightly disturbed.
10-14% Oxygen: Emotional upset, abnormal fatigue,
For routine industrial applications
disturbed respiration.
6-10% Oxygen: Nausea and vomiting, collapse or loss of consciousness.
Below 6%: Convulsive movements, possible respiratory collapse, and death.
OTHER POTENTIAL HEALTH EFFECTS: Acetylene is generally non-irritating to the skin and eyes. Acetylene is
dissolved in a solvent, usually acetone. Any skin or eye contact with the solvent may be slightly irritating to
contaminated skin or eyes.
HEALTH EFFECTS OR RISKS FROM EXPOSURE: An Explanation in Lay Terms. Over-exposure to Acetylene
may cause the following health effects:
ACUTE: The most significant hazard associated with this product is inhalation of oxygen-deficient atmospheres.
Symptoms of oxygen deficiency include respiratory difficulty, ringing in ears, headaches, shortness of breath,
wheezing, headache, dizziness, indigestion, nausea, and, at high concentrations, unconsciousness or death may
occur. The skin of a victim of over-exposure may have a blue color.
CHRONIC: There are currently no known adverse health effects associated with chronic exposure to Acetylene.
TARGET ORGANS: Respiratory system, central nervous system.
4. FIRST-AID MEASURES
RESCUERS SHOULD NOT ATTEMPT TO RETRIEVE VICTIMS OF EXPOSURE TO THIS PRODUCT
WITHOUT ADEQUATE PERSONAL PROTECTIVE EQUIPMENT. At a minimum, Self-Contained
Breathing Apparatus and Fire-Retardant clothing should be worn. Adequate fire protection must
be provided during rescue situations.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 2 OF 8
4. FIRST-AID MEASURES (Continued)
Remove victim(s) to fresh air, as quickly as possible. Only trained personnel should administer supplemental
oxygen and/or cardio-pulmonary resuscitation, if necessary.
SKIN and EYE EXPOSURE: If contact is made with the solvent, flush area for 15 minutes with water.
Victim(s) must be taken for medical attention. Take copy of label and MSDS to physician or other health
professional with victim(s).
5. FIRE-FIGHTING MEASURES
FLASH POINT: Not applicable to a flammable gas.
AUTOIGNITION TEMPERATURE @ 1 atmosphere: 305 掳C (581掳F)
NFPA RATING
FLAMMABLE LIMITS (in air by volume, %): FLAMMABILITY
Lower (LEL): 2.5%
4
Upper (UEL): 82.0%
FIRE EXTINGUISHING MATERIALS: Extinguish fires of this gas by 3
0
HEALTH REACTIVITY
shutting-off the source of the gas, if possible. Use water spray to cool fire-
exposed cylinders, structures and equipment.
UNUSUAL FIRE AND EXPLOSION HAZARDS: When involved in a fire,
this material may decompose and produce toxic gases including carbon OTHER
monoxide and carbon dioxide. Acetylene is extremely flammable and can readily form explosive mixtures with air
over a very wide range. An explosion hazard exists in confined spaces when the gas is released. An explosive
decomposition of pure acetylene can occur under certain conditions of elevated pressure, temperature and container
size.
DANGER! Fires impinging (direct flame) on the outside surface of cylinders of Acetylene can be very dangerous.
Direct flame exposure on the cylinder wall can cause a violent rupture of the cylinder, releasing the contents into a
massive fireball and explosion of released Acetylene. The resulting fire and explosion can result in severe
equipment damage and personnel injury or death over a large area around the cylinders. For fires in large areas,
use unmanned hose holder or monitor nozzles to apply water on those cylinders involved as well as surrounding
cylinders to keep them cool. If this is not possible, withdraw from area and allow fire to burn.
Explosion Sensitivity to Mechanical Impact: Not sensitive.
Explosion Sensitivity to Static Discharge: Static discharge may cause this product to ignite explosively, if
released.
SPECIAL FIRE-FIGHTING PROCEDURES: The best fire-fighting technique may be simply to let the burning gas
escape from the pressurized cylinder or piping system. If possible, stop the leak before extinguishing fire. If the fire
is extinguished before the leak is sealed, the still-leaking Acetylene could explosively re-ignite without warning and
cause extensive damage, injury, or fatality. In this case, increase ventilation (in enclosed areas) to prevent
flammable or explosive mixture formation. Structural fire-fighters must wear Self-Contained Breathing Apparatus
and full protective equipment. Because of the potential for cylinder rupture, evacuation of non-emergency personnel
is essential. If water is not available for cooling or protection of cylinders and exposures, evacuate the area. The
North American Emergency Response Guidebook (Guide #116) recommends 0.5 miles.
6. ACCIDENTAL RELEASE MEASURES
LEAK RESPONSE: Uncontrolled releases should be responded to by trained personnel using pre-planned
procedures. Proper protective equipment should be used. In case of a release, clear the affected area, protect
people, and respond with trained personnel. Adequate fire protection must be provided. Minimum Personal
Protective Equipment should be Level B: fire-retardant protective clothing, gloves and Self-Contained
Breathing Apparatus. Use only non-sparking tools and equipment.
If possible, close the Acetylene cylinder valve to stop the leak. If this does not stop the release (or if it is not
possible to safely reach the cylinder valve), allow the gas to release in-place, or move the cylinder to a safe area,
away from ignition sources. Extreme caution should be used when moving a leaking cylinder of Acetylene.
Monitor the surrounding area for oxygen and combustible gas levels. Combustible gas concentrations must be
below 10% of the LEL (2.5%), and the oxygen content above 19.5% before entry of personnel into the area, without
Self-Contained Breathing Apparatus and protective equipment.
THIS IS AN EXTREMELY FLAMMABLE GAS. Protection of all personnel and the area must be maintained.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 3 OF 8
7. HANDLING and USE
WORK PRACTICES AND HYGIENE PRACTICES: Be aware of any signs of dizziness or fatigue; exposures to
fatal concentrations of this product could occur without any significant warning symptoms.
STORAGE AND HANDLING PRACTICES: Cylinders should be stored upright (with valve-protection cap in place)
and firmly secured to prevent falling or being knocked over. Cylinders can be stored in the open, but in such cases,
should be protected against extremes of weather and from the dampness of the ground to prevent rusting. Cylinders
should be stored in dry, well-ventilated areas away from sources of heat, ignition and direct sunlight. Keep storage
area clear of materials which can burn. Do not allow area where cylinders are stored to exceed 52 掳C (125 掳F).
Store containers away from heavily trafficked areas and emergency exits. Store away from process and production
areas, away from elevators, building and room exits or main aisles leading to exits. Protect cylinders against physical
damage. Post 鈥淣o Smoking or Open Flames鈥? signs in storage or use areas.
In the United States, cylinders of Acetylene stored inside buildings at locations of use must be limited to a total
capacity of 2500 ft3 (70m3). In Canada, the limit is for a total capacity of 2160 ft3 (60m3) in non-sprinklered buildings
and 6130 ft3 (170 m3) in buildings with sprinkler systems. After these quantities are exceeded, a special room must
be built for the storage of Acetylene. The installation of leak detection and alarms for storage areas of Acetylene
must be considered.
Storage areas must meet national electrical codes for Class 1 Hazardous Areas. Have appropriate extinguishing
equipment in the storage area (i.e. sprinkler system, portable fire extinguishers).
Cylinders should be separated from oxygen cylinders, or other oxidizers, by a minimum distance of 20 ft., or by a
barrier of non-combustible material at least 5 ft. high, having a fire-resistance rating of at least 0.5 hours. Isolate
from other incompatible chemicals (refer to Section 10, Stability and Reactivity).
It is important to note that Acetylene, in its free state, under pressure, may decompose violently. The higher the
pressure, the smaller the initial force necessary to cause a reaction. Therefore, never use Acetylene outside the
cylinder at pressures in excess of 15 psig. If pressures exceeding this limit are utilized, special explosion and fire
safety precautions must be implemented.
Keep the smallest amount on-site as is necessary. Full and empty cylinders should be segregated. Use a first-in,
first-out inventory system to prevent full containers from being stored for long periods of time.
Use non-sparking ventilation systems, approved vapor-tight or explosion-proof equipment, and appropriate electrical
systems. Electrical equipment used in gas-handling operations, or located in storage areas, should be non-sparking
or explosion proof. Use a check valve in the discharge line to prevent hazardous backflow. Never tamper with
pressure relief devices in valves and cylinders.
SPECIAL PRECAUTIONS FOR HANDLING GAS CYLINDERS: Compressed gases can present significant safety
hazards. The following rules are applicable to work situations in which cylinders are being used:
Before Use: Move cylinders with a suitable hand-truck. Do not drag, slide or roll cylinders. Do not drop cylinders or
permit them to strike each other. Secure cylinders firmly. Leave the valve protection cap (where provided) in-place
until cylinder is ready for use.
During Use: Use designated CGA fittings and other support equipment. Do not use adapters. Use piping and
equipment adequately designed to withstand pressures to be encountered. Do not heat cylinder by any means to
increase the discharge rate of the product from the cylinder. Do not use oils or grease on gas-handling fittings or
equipment. Do not 鈥渃rack鈥? valve open before connecting it, since ignition may occur. Leak check system with leak
detection solution, never with flame. Immediately contact the supplier if there are any difficulties associated with
operating cylinder valve. Never insert an object (e.g. wrench, screwdriver, pry bar, etc.) into valve cap openings,
doing so may damage valve, causing a leak to occur. Use an adjustable strap wrench to remove over-tight or rusted
caps. Never strike an arc on a compressed gas cylinder or make a cylinder part of an electric circuit.
After Use: Close valve after each use and when empty. Replace valve protection cap. Mark empty cylinders
鈥淓MPTY鈥?.
NOTE: Use only DOT cylinders designed for acetylene storage. Earth-ground and bond all piping systems and
equipment associated with this product.
For welding and brazing operations, refer to ANSI Z-49.1 鈥淪afety in Welding and Cutting鈥? and OSHA safety
regulations for welding, cutting, and brazing (29 CFR 1910.252). In addition, see the National Fire Protection
Association (NFPA) publication 51 Oxygen Fuel Gas Welding and Cutting.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 4 OF 8
7. HANDLING and USE (Continued)
STANDARD VALVE CONNECTIONS FOR U.S. AND CANADA: Use the proper connections, DO NOT USE
ADAPTERS:
Over 50 cubic feet (1.39 m3)
THREADED: CGA 510
Alternate: CGA 300
Between 35 and 75 cubic feet (2.08 m3) CGA 520
Approximately 10 cubic feet (280 L) CGA 200
Canada - Over 50 cubic feet CGA 415
PIN-INDEXED YOKE: Not Applicable.
ULTRA HIGH INTEGRITY: Not Applicable.
PROTECTIVE PRACTICES DURING MAINTENANCE OF CONTAMINATED EQUIPMENT: Follow practices
indicated in Section 6 (Accidental Release Measures). Make certain application equipment is locked and tagged-out
safely. Purge Acetylene-handling equipment with inert gas (i.e. nitrogen) before attempting repairs. Always use
product in areas where adequate ventilation is provided.
8. EXPOSURE CONTROLS - PERSONAL PROTECTION
VENTILATION AND ENGINEERING CONTROLS: Use with adequate ventilation. Provide natural or explosion-
proof ventilation adequate to ensure Acetylene does not reach its lower flammability limit of 2.5%. Local exhaust
ventilation is preferred, because it prevents gas dispersion into the work place by eliminating it at its source. If
appropriate, install automatic monitoring equipment to detect the level of Acetylene and the presence of potentially
explosive air-gas mixtures.
RESPIRATORY PROTECTION: Maintain oxygen levels above 19.5% in the workplace. Use supplied air
respiratory protection if oxygen levels are below 19.5% (air-purifying respirators will not function) or during
emergency response to a release of this product. During an emergency situation, before entering the area, check for
flammable gas level as well as oxygen-deficient atmospheres. If respiratory protection is required, follow the
requirements of the Federal OSHA Respiratory Protection Standard (29 CFR 1910.134), or equivalent State
standards.
EYE PROTECTION: Safety glasses.
HAND PROTECTION: Wear leather gloves when handling cylinders of this product. Otherwise, wear glove
protection appropriate to the specific operation for which this product is used. Wear Solvex or neoprene gloves if
operations could lead to a potential exposure to the solvent.
BODY PROTECTION: Use body protection appropriate for task. Cotton clothing is recommended for use to prevent
static electric build-up. Safety shoes are recommended when handling cylinders.
9. PHYSICAL and CHEMICAL PROPERTIES
GAS DENSITY @ 0掳C (32掳F), 1 atm: 0.07314 lb/ft3 (1.1716 kg/m3)
BOILING POINT @ 10 psig: -75掳C (-103掳F)
FREEZING/MELTING POINT (@ 10 psig: -82.2掳C (-116.掳F)
SPECIFIC GRAVITY OF LIQUID @ -80掳C (-112掳F): 0.613 pH: Not applicable.
SPECIFIC GRAVITY OF GAS @ 0掳C (32掳F) (air = 1): 0.906 MOLECULAR WEIGHT: 26.04
SOLUBILITY IN WATER, vol/vol @ 0掳C (32掳F and 1 atm: 1.7 EXPANSION RATIO: Not applicable.
EVAPORATION RATE (nBuAc = 1): Not applicable. ODOR THRESHOLD: 226 ppm (detection)
SPECIFIC VOLUME OF GAS @ 21.1掳C (70掳F) 1 atm: 14.7 ft /lb (0.918 m3/kg)
3
VAPOR PRESSURE @ 21.1掳C (70掳F): 635 psig ( 4378 kPa)
COEFFICIENT WATER/OIL DISTRIBUTION: Not applicable.
APPEARANCE AND COLOR: Colorless gas. Acetylene of 100% purity is odorless, but commercial purity has a
garlic-like odor.
HOW TO DETECT THIS SUBSTANCE (warning properties): Commercial purity Acetylene has a garlic-like odor
that may be a warning property. In terms of leak detection, fittings and joints can be painted with a soap solution to
detect leaks, which will be indicated by a bubble formation.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 5 OF 8
10. STABILITY and REACTIVITY
STABILITY: Acetylene is stable at standard temperatures and pressures. Gaseous acetylene may decompose
violently at elevated temperatures and pressures. Acetylene must not be used above pressure greater than 15 psig.
The higher the pressure, the more likely it is for a reaction to occur.
DECOMPOSITION PRODUCTS: Carbon and hydrogen. When ignited in the presence of oxygen, carbon monoxide
and carbon dioxide will be generated.
MATERIALS WITH WHICH SUBSTANCE IS INCOMPATIBLE: Acetylene is not compatible with the following
materials: Strong oxidizers (i.e. chlorine, bromine pentafluoride, oxygen, oxygen difluoride, and nitrogen trifluoride);
calcium hypochlorite; various heavy metals (copper, silver, mercury, brass with a copper content exceeding 65%)
and the salts of these metals; halogens (bromine, chlorine, iodine, fluorine); hydrides (i.e. sodium hydride, cesium
hydride); ozone; perchloric acid; potassium.
HAZARDOUS POLYMERIZATION: Can occur when heated or under pressure.
CONDITIONS TO AVOID: Contact with incompatible materials and exposure to heat, sparks and other sources of
ignition. Cylinders exposed to high temperatures or direct flame can rupture or burst.
11. TOXICOLOGICAL INFORMATION
TOXICITY DATA: The following information is for Acetylene.
TCLo (inhalation, human) = 20 pph; central nervous system, respiratory system effects.
LCLo (inhalation, human) = 500,000 ppm/5 minutes
Other data pertaining to the effects of Acetylene inhalation on humans are as follows:
Concentration Symptom
100,000 ppm Intoxication (drowsiness, dizziness, giddiness).
200,000 ppm Severe intoxication.
300,000 ppm Loss of coordination.
350,000 ppm Unconsciousness after 5 minutes of exposure.
Effects on Short-Term Inhalation: Animals have shown tolerance to 10% Acetylene. In studies with dogs, cats, and rabbits, Acetylene
acts as an anesthetic at 20% exposure. Recovery occurs if the oxygen level is maintained. In an oxygen-deficient environment, death
may occur after 5-10 minutes. Rodents exposed to 25, 50, and 80 percent Acetylene in oxygen for 1-2 hours daily (93 hours total
exposure), evidenced no weight change or cellular damage. Mixtures of 80% Acetylene/20% oxygen caused a rise in blood pressure
in an exposed cat.
SUSPECTED CANCER AGENT: Acetylene is not found on the following lists: FEDERAL OSHA Z LIST, NTP,
IARC, CAL/OSHA, and therefore is not considered to be, nor suspected to be a cancer-causing agent by these
agencies.
IRRITANCY OF PRODUCT: This product is not irritating; however, contact with the solvent can be slightly irritating
to contaminated skin or eyes.
SENSITIZATION TO THE PRODUCT: Acetylene is not known to cause sensitization in humans.
REPRODUCTIVE TOXICITY INFORMATION: Listed below is information concerning the effects of Acetylene on
the human reproductive system.
Mutagenicity: No mutagenicity effects have been described for Acetylene.
Embryotoxcity: No embryotoxic effects have been described for Acetylene.
Teratogenicity: No teratogenicity effects have been described for Acetylene.
Reproductive Toxicity: No reproductive toxicity effects have been described for Acetylene.
A mutagen is a chemical which causes permanent changes to genetic material (DNA) such that the changes will
propagate through generation lines. An embryotoxin is a chemical which causes damage to a developing embryo
(i.e. within the first eight weeks of pregnancy in humans), but the damage does not propagate across generational
lines. A teratogen is a chemical which causes damage to a developing fetus, but the damage does not propagate
across generational lines. A reproductive toxin is any substance which interferes in any way with the reproductive
process.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Acute or chronic respiratory conditions may be
aggravated by over-exposure to Acetylene.
BIOLOGICAL EXPOSURE INDICES (BEIs): Currently, Biological Exposure Indices (BEIs) are not applicable for
Acetylene.
RECOMMENDATIONS TO PHYSICIANS: Administer oxygen, if necessary; treat symptoms; reduce or eliminate
exposure.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 6 OF 8
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL STABILITY: Acetylene will be dissipated rapidly in well-ventilated areas. The following
environmental data are available for acetylene.
ACETYLENE: Water Solubility = 100 vol./100 vol. at 18 EC. Acetylene is not expected to be harmful to aquatic life. Only moderately toxic to fish.
Volatility and low solubility suggest it would be rare for water to become critically polluted from accidental releases. Acetylene is biodegraded
through various plant and bacterial systems by inactivating atmospheric acetylene through their nitrogen- fixing mechanisms.
EFFECT OF MATERIAL ON PLANTS or ANIMALS: Any adverse effect on animals would be related to oxygen
deficient environments and the anesthetic properties of Acetylene at high concentrations of exposure. No adverse
effect is anticipated to occur to plant-life.
EFFECT OF CHEMICAL ON AQUATIC LIFE: No evidence is currently available on Acetylene鈥檚 effects on aquatic
life.
13. DISPOSAL CONSIDERATIONS
PREPARING WASTES FOR DISPOSAL: Waste disposal must be in accordance with appropriate Federal, State,
and local regulations. Return cylinders with any residual product to Air Liquide. Do not dispose of locally.
14. TRANSPORTATION INFORMATION
THIS MATERIAL IS HAZARDOUS AS DEFINED BY 49 CFR 172.101 BY THE U.S. DEPARTMENT OF
TRANSPORTATION.
PROPER SHIPPING NAME: Acetylene, dissolved
HAZARD CLASS NUMBER and DESCRIPTION: 2.1 (Flammable Gas)
UN IDENTIFICATION NUMBER: UN 1001
PACKING GROUP: Not applicable.
DOT LABEL(S) REQUIRED: Flammable Gas
NORTH AMERICAN EMERGENCY RESPONSE GUIDEBOOK NUMBER (1996): 116
MARINE POLLUTANT: Acetylene is not classified by the DOT as a Marine Pollutant (as defined by 49 CFR
172.101, Appendix B).
NOTE: Shipment of compressed gas cylinders which have not been filled with the owners consent is a violation of
Federal law (49 CFR, Part 173.301 (b)).
TRANSPORT CANADA TRANSPORTATION OF DANGEROUS GOODS REGULATIONS: THIS MATERIAL IS
CONSIDERED AS DANGEROUS GOODS. Use the above information for the preparation of Canadian Shipments.
15. REGULATORY INFORMATION
SARA REPORTING REQUIREMENTS: Acetylene is not subject to the reporting requirements of Sections 302, 304
and 313 of Title III of the Superfund Amendments and Reauthorization Act.
SARA THRESHOLD PLANNING QUANTITY: Not applicable.
TSCA INVENTORY STATUS: Acetylene is listed on the TSCA Inventory.
CERCLA REPORTABLE QUANTITY (RQ): Not applicable.
OTHER U.S. FEDERAL REGULATIONS:
鈥? Acetylene is subject to the reporting requirements of Section 112(r) of the Clean Air Act. The Threshold Quantity
for this gas is 10,000 pounds.
鈥? Depending on specific operations involving the use of this product, the regulations of the Process Safety
Management of Highly Hazardous Chemicals may be applicable (29 CFR 1910.119). Under this regulation
Acetylene is not listed in Appendix A, however, any process that involves a flammable gas on-site, in one
location, in quantities of 10,000 lbs (4,553 kg) or greater is covered under this regulation unless it is used as a
fuel.
鈥? Acetylene does not contain any Class I or Class II ozone depleting chemicals (40 CFR part 82).
鈥? Acetylene is listed in Table 3 as a Regulated Substance in quantities of 10,000 lbs (4,553 kg) or greater, per 40
CFR, Part 68, of the Risk Management for Chemical Accidental Release Prevention.
OTHER CANADIAN REGULATIONS: Acetylene is categorized as a Controlled Product, Hazard Classes A, B1, F
as per the Controlled Product Regulations.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 7 OF 8
15. REGULATORY INFORMATION (Continued)
STATE REGULATORY INFORMATION: Acetylene is covered under specific State regulations, as denoted below:
Alaska - Designated Toxic and Hazardous Massachusetts - Substance List: Acetylene. Pennsylvania - Hazardous Substance List:
Acetylene.
Substances: Acetylene. Minnesota - List of Hazardous Substances:
Acetylene. Rhode Island - Hazardous Substance List:
California - Permissible Exposure Limits
Acetylene.
Missouri - Employer Information/Toxic
for Chemical Contaminants: Acetylene.
Texas - Hazardous Substance List: No.
Substance List: Acetylene.
Florida - Substance List: Acetylene.
West Virginia - Hazardous Substance List:
New Jersey - Right to Know Hazardous
Illinois - Toxic Substance List: Acetylene.
No.
Substance List: Acetylene.
Kansas - Section 302/313 List: No.
Wisconsin - Toxic and Hazardous
North Dakota - List of Hazardous
Substances: No.
Chemicals, Reportable Quantities: No.
CALIFORNIA PROPOSITION 65: Acetylene is not on the California Proposition 65 lists.
16. OTHER INFORMATION
MIXTURES: When two or more gases or liquefied gases are mixed, their hazardous properties may combine to
create additional, unexpected hazards. Obtain and evaluate the safety information for each component before
you produce the mixture. Consult an Industrial Hygienist or other trained person when you make your safety
evaluation of the end product. Remember, gases and liquids have properties which can cause serious injury or
death.
Further information about acetylene can be found in the following pamphlets and videos published by:
Compressed Gas Association Inc. (CGA), 4221 Walney Road 5th floor, Chantilly, VA 20151-2923: (703) 788-
2700.
G-1 鈥淎cetylene鈥?
G-1.1 鈥淐ommodity Specification for Acetylene鈥?
P-1 鈥淪afe Handling of Compressed Gases in Containers鈥?
SB-4 鈥淗andling Acetylene Cylinders in Fire Situations鈥?
SB-8 鈥淯se of Oxy-fuel Gas Welding and Cutting Apparatus鈥?
AV-9 鈥淗andling Acetylene Cylinders in Fire Situations鈥?
鈥淗andbook of Compressed Gases鈥?
PREPARED BY: CHEMICAL SAFETY ASSOCIATES, Inc.
9163 Chesapeake Drive, San Diego, CA 92123-1002
619/565-0302
This Material Safety Data Sheet is offered pursuant to OSHA鈥檚 Hazard Communication Standard, 29 CFR, 1910.1200. Other government
regulations must be reviewed for applicability to this product. To the best of Air Liquide鈥檚 knowledge, the information contained herein is
reliable and accurate as of this date; however, accuracy, suitability or completeness are not guaranteed and no warranties of any type, either
express or implied, are provided. The information contained herein relates only to this specific product. If this product is combined with other
materials, all component properties must be considered. Data may be changed from time to time. Be sure to consult the latest edition.
ACETYLENE - C2H2 MSDS EFFECTIVE DATE: JANUARY 16, 2004
PAGE 8 OF 8
|