MSDS- Page 1 of 6
According to ANSI- Z400.1-1993 16-Section MSDS format.
Date Prepared: October 11, 2006
Number: RJSSH061031MSDSUS
SECTION I - IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND COMPANY/UNDERTAKING
PRODUCT IDENTITY: (As Used on Label and List)
Product Name: Anaerobic adhesive
Type: Hx series (see remark#)
Trade Name: Hx
MANUFACTURER/SUPPLIER INFORMATION:
Manufacturer's Name:
Zhuhai Hengxin Chemical Industry Co., Ltd.
Address:
Building No.5, Xinye Road, Cuiwan Industrial District, Guangchang, Nanping, Zhuhai, Guangdong, 519060,
China
Emergency Telephone Number: +86-756-3899907
Fax Number for Information: +86-756-3899913
Contact Person: Liu Chulin
E-mail: zhhengxin@sina.com
Remark#: Hx series - Hx186, Hx188, Hx222, Hx242, Hx243, Hx262, Hx268, Hx271, Hx272, Hx277, Hx290,
Hx340, Hx510, Hx515, Hx518, Hx545, Hx554, Hx567, Hx569, Hx577, Hx603, Hx609, Hx620, Hx638, Hx641,
Hx648, Hx660, Hx680, Hx512, Hx547
SECTION II - COMPOSITION/INFORMATION ON INGREDIENTS
All components of this product are listed on TSCA inventory of chemical substances maintained by the U.S.
environmental protection agency.
This product is complied with RoHS.
RJS STANDARDS TESTING & CERTIFICATION CENTER
141-04 14th Avenue, Whitestone, New York 11357, USA.
MSDS- Page 2 of 6
SECTION III - HAZARDS IDENTIFICATION
Route of entry: Inhalation, skin contact, eye contact, ingestion.
Eye: May cause eye irritation, tearing and redness.
Skin: Slightly hazardous in case of skin contact (irritant) for long-term contact.
Ingestion: May be harmful if swallowed. Large amount ingestion may cause nausea.
Inhalation: Minute amounts aspirated into the lungs may cause mild pulmonary irritation.
Note: Read the entire MSDS for a more thorough evaluation of the hazards.
SECTION IV - FIRST AID MEASURES
Eye Contact: If contact with the eye(s), wash with running water holding eyelid(s) open. Take care not to rinse
contaminated water into the non-affected eye. In all cases of eye contamination it is a sensible precaution to
seek medical attention.
Skin Contact: Wash affected area thoroughly with plenty of running water. If symptoms develop seek medical
attention.
Inhalation: Remove from exposure to fresh air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Get medical aid immediately.
Ingestion: If victim is conscious and alert, give 2-4 cupfuls of milk or water. Do not induce vomiting. If a large
amount has been swallowed, or if symptoms develop, seek medical attention.
SECTION V - FIRE FIGHTING MEASURES
Flash Point: >100
Upper Flame Limit (Volume % in air): 15%
Lower Flame Limit (Volume % in air): 5%
Extinguishing Media:
Water spray, foam, dry chemical, carbon dioxide.
Fire and Explosion Hazards: Flammable if heated. Mechanical and thermal processes may produce dust and
flammable vapors, which may be potential explosion hazards. Tightly sealed containers may burst under fire or
intense heat.
Special Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or
equivalent), and full protective gear. Combustion generates toxic fumes.
RJS STANDARDS TESTING & CERTIFICATION CENTER
141-04 14th Avenue, Whitestone, New York 11357, USA.
MSDS- Page 3 of 6
SECTION VI - ACCIDENTAL RELEASE MEASURES
In Case of Spill or Other Releases:
Always wear recommended personal protective equipment.
Small spill: Take up water/sand or other material (cotton yarn). Place in container for later disposal.
Large spill: Product absorbed on inert material may polymerize generating heat & pressure. Vent container.
Spills and releases may have to be reported to Federal and/or local authorities. See the Regulatory
Information section (XV) regarding reporting requirements.
SECTION VII - HANDLING AND STORAGE
Handling: Keep far away from fire sources, heated or molten product when handling. Washing thoroughly after
handling. Avoid contact with eyes and skin. Avoid ingestion.
Storage: Store in a cool (<25 ), dry, and well-ventilated area and away from sources of ignition, excessive heat
and direct sunlight. Keep container closed when not in use. Protect from physical damage. Separate from
combustible and incompatible material. Put it lightly when packing and transport, prevent the packing and
container from damage.
SECTION VIII - EXPOSURE CONTROLS/PERSONAL PROTECTION
Ventilation:
Respiratory protection is not normally necessary unless product is used in enclosed area of poor ventilation or
individual has a history of chronic respiratory disease. Local exhaust is recommended.
Protective Gloves:
Protective gloves are recommended for individuals with known skin sensitivities. Always wash hands thoroughly
after use.
Eye Protection:
Safety glasses with side shields is recommended in good practice. Avoid eye contact.
Protective Clothing:
Be required in ordinary use and in workshop.
Work Hygienic Practices:
After complete the work, taking off the clothes and having a bath, avoiding a long-term getting in touch with it
again and again.
RJS STANDARDS TESTING & CERTIFICATION CENTER
141-04 14th Avenue, Whitestone, New York 11357, USA.
MSDS- Page 4 of 6
Respiratory Protection:
Don't need a special protection generally. Can wear the ventilated type of mask or anti-virus mask when get in
touch with high density of product. If ventilation does not maintain inhalation exposures below PEL (TLV), use
NIOSH/MSHA approved respirator as per current 29 CFR 1910.134, instructions/warnings and NIOSH-respirator
selection.
Additional protective measures:
Wash after use and before eating, drinking or smoking.
Section IX - PHYSICAL AND CHEMICAL PROPERTIES
Colour: Red/yellow/blue/green/ purple/white.
Physical State: Liquid.
Odor: Mild irritative odor.
Specific Gravity (at 20 ) (water =1): 1.0-1.3
pH: 4-6
Boiling Point: >200
Vapor Density (Air=1): 1.2
Solubility in Water (Weight %): Nonsoluble.
VOC: 0.5%
Viscosity: 10-150000mpa.s
SECTION X - STABILITY AND REACTIVITY
Normally Stable:
This product is stable under ordinary conditions of use.
Incompatibilities:
Oxidizing and reducing agents.
Conditions to Avoid:
Direct sunlight, excessive heat and physical damage.
Hazardous Decomposition Products:
Depending on conditions of fire, CO, CO2, nitrous oxides, irritating and toxic fumes and gases and other possible
byproducts may be generated.
Hazardous Polymerization:
Will not occur.
RJS STANDARDS TESTING & CERTIFICATION CENTER
141-04 14th Avenue, Whitestone, New York 11357, USA.
MSDS- Page 5 of 6
SECTION XI - TOXICOLOGICAL INFORMATION
Carcinogenicity:
IARC: Not established.
National Toxicology Program: Not established.
OSHA: Not established.
Reproduction Toxicity: Not available.
Teratogenicity: Not available.
Mutagenicity: Not available.
Synergistic Products: Not available.
SECTION XII - ECOLOGICAL INFORMATION
No data have been developed on this subject. These polymeric products are not soluble in water. They are not
considered biodegradable.
On the basis of available information, this material is not expected to produce any significant adverse
environmental effects when recommended use instructions are followed.
SECTION XIII - DISPOSAL CONSIDERATIONS
Waste Disposal Method:
Recover or recycle if possible. Put into dustbin, otherwise incineration, otherwise licensed landfill, or safe
disposal as required by local, state, federal, international or country specific regulations. Large quantities of this
product should not be allowed to enter drains or water lines or be deposited where it can affect ground or surface
waters.
Empty Container Warnings:
Empty containers may contain product residue, follow MSDS and label warnings even after they have been
emptied.
SECTION XIV - TRANSPORT INFORMATION
DOT (Department of Transportation): Not regulated.
Proper Shipping Name: Not regulated.
Information reported for product/size: In bulk or in Box.
Hazard Class: Not regulated.
Identification Number: Not applicable.
IMO: Not regulated.
RJS STANDARDS TESTING & CERTIFICATION CENTER
141-04 14th Avenue, Whitestone, New York 11357, USA.
MSDS- Page 6 of 6
IATA/ICAO Class: Not regulated.
UN Hazard Codes: Class 4.1
The regulations may change from time to time. Please consult the most recent version of the relevant regulations.
Follow all regulations in your country.
SECTION XV - REGULATORY INFORMATION
NFPA Hazard Code:
Health hazard rating is 1, slightly hazardous.
Fire hazard is 1, Flash point above 200掳F.
Reactivity rating is 0, stable
Special Hazard: None
For details regulations you should contact the appropriate agency in your country.
SECTION XVI - OTHER INFORMATION
The information above is believed to be accurate and represents the best information currently available to us.
However, we make no warranty of merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users should make their own investigations
to determine the suitability of the information for their particular purposes. In no way shall the company be liable
for any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental,
consequential or exemplary damages, howsoever arising, even if the company has been advised of the
possibility of such damages.
NOTE
This Material Safety Data Sheet (MSDS) is for guidance and is based upon information and tests believed to be reliable.
RJS Standard Testing & Certification Center makes no guarantee of the accuracy or completeness of the data and shall not
be liable for any damages relating there to. The data is offered solely for your consideration, investigation, and verification.
RJS Standard Testing & Certification Center assumes no legal responsibility for use or reliance upon this data.
RJS STANDARDS TESTING & CERTIFICATION CENTER
141-04 14th Avenue, Whitestone, New York 11357, USA.
|