Material Safety Data Sheet
A-C庐 Polyethylene Homopolymers
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: A-C庐 Polyethylene Homopolymers
OTHER/GENERIC NAMES: A-C庐 3A, 6, 6A, 6S, 7, 7A, 7AS, 8, 8A, 9, 9A, 9CF, 9F, 9W, 15, 16, 16A,
617, 617A, 617G, 715, 725, 735, 1702
PRODUCT USE: Multiple uses in many applications.
MANUFACTURER: Honeywell International Inc.
101 Columbia Road
P.O. Box 1139
Morristown, New Jersey 07962-1139
FOR MORE INFORMATION CALL: IN CASE OF EMERGENCY CALL:
(Monday-Friday, 8:00am-5:00pm) (24 Hours/Day, 7 Days/Week)
1-800-707-4555 1-800-498-5701
FOR TRANSPORTATION EMERGENCIES:
1-800-424-9300 (CHEMTREC 鈥? Domestic)
1-613-966-6666 (CANUTEC 鈥? Canada)
2. COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT NAME CAS NUMBER WEIGHT %
Polyethylene 9002-88-4 ~100
Trace impurities and additional material names not listed above may also appear in Section 15 towards
the end of the MSDS. These materials may be listed for local "Right-To-Know" compliance and for other
reasons.
While this material is not considered as hazardous under OSHA regulations, the MSDS contains valuable
information critical to the safe handling and proper use of the product. This MSDS should be retained
and available for employees and other users of this product.
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW: A-C 1702 products are grease-like. All other products
are white waxy solids in pellet, prill or powder form. Dust from this product may
form an explosive mixture in air. Not considered hazardous under normal
conditions of use. Can release irritating and/or toxic fumes and vapors if involved
in a fire.
MSDS Number: ACPA0003 Page 1 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
POTENTIAL HEALTH HAZARDS
SKIN: May cause mechanical irritation if the product comes into contact with the skin. Contact with
molten material may cause thermal burns.
EYES: May cause mechanical irritation if product comes into contact with the eye.
INHALATION: Not a probable route of exposure under normal conditions of use. Elevated
processing temperatures may generate fumes and vapors which may cause irritation
to the nose and throat.
INGESTION: Not a probable route of exposure. Not considered hazardous.
DELAYED EFFECTS: None known.
Ingredients found on one of the OSHA designated carcinogen lists are listed below.
INGREDIENT NAME NTP STATUS IARC STATUS OSHA LIST
No ingredients listed in this section.
4. FIRST AID MEASURES
SKIN: If in contact with solid material, wash with soap and water. If in contact with molten material,
submerge injured area in cold water. Do not attempt to remove material adhering to the skin.
Get medical attention if irritation develops or persists.
EYES: Flush eyes with plenty of water. Get medical attention if irritation develops or persists.
INHALATION: If exposed to vapors at elevated processing conditions, remove to fresh air. Get medical
attention if irritation develops or persists.
INGESTION: Not a probable route of exposure. If person is conscious, rinse mouth with water. Do not
induce vomiting unless directed to do so by a physician.
ADVICE TO PHYSICIAN: No specific advice, treat symptomatically.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
FLASH POINT: >445 掳F (>230 掳C)
FLASH POINT METHOD: Open cup.
AUTOIGNITION TEMPERATURE: Not determined.
UPPER FLAME LIMIT (volume % in air): Not applicable.
LOWER FLAME LIMIT (volume % in air): Not applicable.
FLAME PROPAGATION RATE (solids): Not determined.
OSHA FLAMMABILITY CLASS: Combustible solid.
MSDS Number: ACPA0003 Page 2 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
EXTINGUISHING MEDIA:
Use water fog, dry chemical, carbon dioxide or foam as appropriate for materials in surrounding fire.
Avoid using direct streams of water on molten burning material as it may scatter and spread the fire.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Melts in proximity to fires resulting in slippery floors and stairs. Static charges on powders or powders
in liquids may ignite combustible atmospheres. Airborne dusts of this product in an enclosed space
and in the presence of an ignition source may constitute an explosion hazard. See NFPA Bulletin 654,
鈥淪tandard for the Prevention of Fire and Dust Explosions from the Manufacturing, Processing, and
Handling of Combustible Particulate Solids,鈥? for safe handling procedures.
SPECIAL FIRE FIGHTING PRECAUTIONS/INSTRUCTIONS:
As in any fire, wear NIOSH/MSHA approved positive pressure self-contained breathing apparatus and
full protective clothing. Watch footing on floors and stairs because of possible spreading of molten
material.
6. ACCIDENTAL RELEASE MEASURES
IN CASE OF SPILL OR OTHER RELEASE: (Always wear recommended personal protective equipment.)
Avoid generating dust. Keep away from heat or flame. Collect material and place in a container for re-
use or disposal. If material is molten, allow to cool. Use caution, as material may still be hot after
solidification.
Spills and releases may have to be reported to Federal and/or local authorities. See Section 15
regarding reporting requirements.
7. HANDLING AND STORAGE
NORMAL HANDLING: (Always wear recommended personal protective equipment.)
Avoid spillage which can cause very slippery conditions on floors. Follow standard personal hygiene
and housekeeping practices for an industrial environment.
STORAGE RECOMMENDATIONS:
To maintain product quality, store in a cool, dry area, away from direct heat or sunlight. Do not store
near strong oxidizing agents and amines.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS:
General room ventilation is adequate for storage and ordinary handling. Use local exhaust at points of
fume generation or if dusty conditions prevail to maintain exposure below the PEL/TLV exposure
limits.
PERSONAL PROTECTIVE EQUIPMENT
SKIN PROTECTION:
Not normally required. Use heat-protective clothing as needed for handling hot material.
MSDS Number: ACPA0003 Page 3 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
EYE PROTECTION:
Wear safety glasses or goggles that conform to ANSI Z87.1 under normal conditions. Wear safety
goggles and/or a full-face shield if there is potential for contact with molten material.
RESPIRATORY PROTECTION:
Not required for properly ventilated areas. If there is potential for inhalation of dust or vapor, wear
a NIOSH approved respirator.
The respirator must be selected based on contamination levels and use conditions found in the
workplace. Use conditions must not exceed the working limits of the respirator. The respirator
must be used in accordance with the OSHA respiratory protection standard (29 CFR 1910.134).
ADDITIONAL RECOMMENDATIONS:
Provide safety showers and eyewash stations in close proximity to the work area.
EXPOSURE GUIDELINES
INGREDIENT NAME ACGIH TLV OSHA PEL OTHER LIMIT
Particulates (insoluble or poorly TWA = 10 mg/m3 TWA = 15 mg/m3 None.
soluble), Not Otherwise Specified (8-hr day, (8-hr day, total
inhalable fraction), dust),
TWA = 3 mg/m3 TWA = 5 mg/m3
(8-hr day, (8-hr day,
respirable fraction) respirable fraction)
* = Limit established by Honeywell for internal use.
** = Workplace Environmental Exposure Level (AIHA).
*** = Biological Exposure Index (ACGIH).
PEL values represent limits established by the 1989 Air Contaminants Rule (29 CFR 1910.1000,
Subpart Z, Table Z-1-A) which was subsequently revoked on June 30, 1993. Several states continue to
enforce Table Z-1-A limits.
OTHER EXPOSURE LIMITS FOR POTENTIAL DECOMPOSITION PRODUCTS:
None.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: A-C庐 1702 products are grease-like, other grades are white pellets, prills or powders.
PHYSICAL STATE: Solid.
ODOR: Characteristic waxy odor.
SPECIFIC GRAVITY (water = 1.0): 0.88 鈥? 0.97
SOLUBILITY IN WATER (weight %): Negligible.
pH: Not applicable.
BOILING POINT: Not determined.
MELTING POINT: 200 鈥? 250 掳F (92 鈥? 122 掳C)
VAPOR PRESSURE: Not applicable.
VAPOR DENSITY (air = 1.0): Not applicable.
EVAPORATION RATE: Not determined. COMPARED TO: Not applicable.
MSDS Number: ACPA0003 Page 4 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
% VOLATILES: Not determined.
FLASH POINT: >445 掳F (>230 掳C)
(Flash point method and additional flammability data are found in Section 5.)
10. STABILITY AND REACTIVITY
NORMALLY STABLE? (CONDITIONS TO AVOID)
Normally stable. Avoid exposure to open flame or temperatures exceeding recommended processing
conditions. Honeywell should be contacted if questions arise concerning specific processing
conditions.
INCOMPATIBILITIES:
Strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS:
Thermal decomposition products may include carbon monoxide, carbon dioxide and combustion by-
products (oxidized and non-oxidized hydrocarbons).
HAZARDOUS POLYMERIZATION:
Will not occur.
11. TOXICOLOGICAL INFORMATION
IMMEDIATE (ACUTE) EFFECTS:
Oral, rat LD50: >2,000 mg/kg
Oral, mouse LDLo: 5,000 mg/kg
DELAYED (SUBCHRONIC AND CHRONIC) EFFECTS:
No data available.
OTHER DATA:
None.
12. ECOLOGICAL INFORMATION
No data available. Material is considered inert and not expected to be biodegradable.
13. DISPOSAL CONSIDERATIONS
RCRA
Is the unused product a RCRA hazardous waste if discarded? No.
If yes, the RCRA ID number is: Not applicable.
OTHER DISPOSAL CONSIDERATIONS:
Dispose of in compliance with Federal, state and local government regulations. Disposal options
include: recycling, incineration and landfilling.
MSDS Number: ACPA0003 Page 5 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
The information offered here is for the product as shipped. Use and/or alterations to the product such as
mixing with other materials may significantly change the characteristics of the material and alter the
RCRA classification and the proper disposal method.
14. TRANSPORT INFORMATION
US DOT HAZARD CLASS: Not regulated.
US DOT ID NUMBER: Not applicable.
For additional information on shipping regulations affecting this material, contact the information number
found on Section 1.
15. REGULATORY INFORMATION
TOXIC SUBSTANCES CONTROL ACT (TSCA)
TSCA INVENTORY STATUS: All components are listed on the TSCA Inventory.
OTHER TSCA ISSUES: None.
SARA TITLE III/CERCLA
"Reportable Quantities" (RQs) and/or "Threshold Planning Quantities" (TPQs) exist for the following
ingredients.
INGREDIENT NAME SARA/CERCLA RQ (lb) SARA EHS TPQ (lb)
No ingredients listed in this section.
Spills resulting in the loss of any ingredient at or above its RQ requires immediate notification
to the National Response Center (1-800-424-8802) and to your Local Emergency Planning
Committee.
SECTION 311 HAZARD CLASS: None.
The following ingredients are SARA 313 "Toxic Chemicals". CAS numbers and weight percents are
found in Section 2.
INGREDIENT NAME COMMENT
No ingredients listed in this section.
STATE RIGHT-TO-KNOW
In addition to the ingredients found in Section 2, the following are listed for state right-to-know
purposes.
MSDS Number: ACPA0003 Page 6 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
INGREDIENT NAME WEIGHT % COMMENT
No ingredients listed in this section.
ADDITIONAL REGULATORY INFORMATION
FOOD AND DRUG ADMINISTRATION (USA):
See Honeywell Technical Data Bulletin GEN-002 for FDA-related information.
Honeywell does not promote or support the use of its products in applications which are intended
for permanent implantation in the human body or in permanent contact with internal bodily
tissues or fluids.
WHMIS CLASSIFICATION (CANADA):
Not a controlled product.
FOREIGN INVENTORY STATUS:
All components of this product are listed on the following inventories:
Australian
Canadian (DSL)
Chinese
European (EINECS)
Japanese (ENCS)
Korean
Philippine (PICCS)
16. OTHER INFORMATION
CURRENT ISSUE DATE: June, 2005
PREVIOUS ISSUE DATE: February, 2004
CHANGES TO MSDS FROM PREVIOUS ISSUE DATE ARE DUE TO THE FOLLOWING:
Added A-C庐 9W and A-C庐 15 to product list and change in emergency contact information (Section 1).
OTHER INFORMATION:
HMIS庐 III ratings for the product are as follows:
Health (H) 0
Flammability (F) 1
Physical Hazards (PH) 0
HMIS庐 III ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Recipients of this MSDS should not employ any
recommended HMIS庐 III ratings in the absence of a fully implemented HMIS庐 III hazard
communication program.
MSDS Number: ACPA0003 Page 7 of 8
Current Issue Date: June, 2005
MATERIAL SAFETY DATA SHEET
A-C庐 Polyethylene Homopolymers
The above HMIS庐 III ratings are from the HMIS庐 Third Edition. There have been significant changes
made to the system since the second edition. 鈥淧hysical Hazards鈥? or 鈥淧H鈥? replaces the former
鈥淩eactivity鈥? or 鈥淩鈥? rating. For a more detailed explanation of the system and the ratings, please refer to
the HMIS庐 Implementation Manual, Third Edition.
MSDS Number: ACPA0003 Page 8 of 8
Current Issue Date: June, 2005
|