MATERIAL SAFETY DATA SHEET
1. PRODUCT IDENTIFICATION AND COMPANY INFORMATION
Product Name : Solderpaste-(63Sn/37Pb(62Sn/36Pb/2Ag) Revised Date: 2003 Dec 27
Part Number: DS-0201
MSDS Number: DSMSDS0201
Manufacturer Information.
Company Name: Danyang Solec Co., Ltd
Address: 334-4 Ssangsongri Mado-myeon, Hwaseong-Si, Kyunggi-Do S.Korea
Tel : 82-31-355-9133 Fax : 82-31-355-9138
2. COMPOSITION AND INGREDIENTS INFORMATION
INGREDIENTS CAS NUMBER mg/m3 wt(%) OSHA PEL mg/m3 ACGIH TLV mg/m3
Tin (Sn) 7440-31-5 56.3(55.4)~57.2(56.3) 2.0mg/cum 2.0mg/cum
Lead (Pd) 7439-92-1 32.8(32.0)~33.7(32.8) 0.05mg/cum 0.5mg/cum
(Silver) (Ag) 7440-22-4 (1.6~2.0) 0.01mg/cum 0.10mg/cum
Polymer Alcohol 1559-36-0 5 ~ 10
Rosin 8050-09-7 <5.0
Etc - <1.0
3. PHYSICAL DATA PUBLISHED OR ESTIMATED VALUES
MELTING POINT (Deg.鈩? ) 206鈩? (201鈩?)l
SPECIFIC GRAVITY (H2O=1) (@ 77 deg F) 8.4 (8.41)
VAPOR PRESSURE (mm Hg at 20 Deg. 鈩?) N.A
BOILING POINT Deg F (760 mm Hg) N.A
% VOLATILE BY WEIGHT N.A
EVAPORATION RATE (BUAC=1) N.A
PH (5% aqueous soln.) N.A
VAPOR DENSITY (AIR=1) N.A
SOLUBILITY IN WATER Non Soluble
APPEARANCE AND ODOR Gray Paste
4. FIRE AND EXPLOSION HAZARD DATA
ESTIMATED FLAMMABLE LIMITS (% By Volume in Air) LEL : NA UEL : NA
FLASH POINT Deg F. NE
Carbon dioxide or dry chemical
EXTINGUISHING MEDIA
Use self-contained breathing
SPECIAL FIREFIGHTING PROCEDURES
Apparatus in enclosed area
Vapors are heavier than air and may travel along ground
UNUSUAL FIRE & EXPLOSION HAZARD
Never use welding torch on or near containers even empty)
NA - NOT APPLICABLE NE - NOT ESTABLISHED UN 鈥揢NKOWN
Head office Tel: 82-31-355-9133 Fax : 82-31-355-9138 Address : 334-4 Ssangsongri Mado-myeon, Hwaseong-Si, Kyunggi-Do S.Korea
India Office 0422-231-1349 Hong Kong Office 852-2100-3205 China Office 86-755-2641-0271 Thailand Office 662- 643-9060
Malays ia Office 6 0 7- 5 1 2- 3 39 9 T aiwan Office 8 8 6- 2- 2 7 5 8- 0 9 2 0 UK o ffice 44 - 87 0- 4 5 9- 2673 Germany Office 49-745-162-4001
Italy Office 39-02-9904-6509 Finland Office 358-2630-5913 Spain Office 34-91-386-7139 USA Office 408-844-0400
MATERIAL SAFETY DATA SHEET
5. HEALTH HAZARDS IDENTIFICATION PUBLISHED OR ESTIMATED VALUE
Symptoms/Effects Of Overexposure Emergency and First Procedures
If affected, remove individual to fresh air.
INHALATION Can cause nasal irritation, dizziness, nausea, headache.
If breathing is difficult, administer oxygen.
Call physician or Poison Control Center immediately.
Can cause gastrointestinal irritation, nausea, vomiting and
INGESTION diarrhea Never give anything by mouth to an unconscious person
Prolonged or repeated contact can cause defatting,
SKIN Wash exposed area with soap and water. Remove
contaminated clothing.
CONTACT cracking of the skin and possible dermatitis.
EYE Flush with large amount of water, lifting upper and
Can cause severe irritation, tearing, blurred vision.
lower lids occasionally. Get medical attention.
CONTACT
LISTED
None None
CARCINOGENS
6. REACTIVITY DATA
STABILITY : STABLE
CONDITIONS TO AVOID : None
INCOMPATABILITY (Materials to Avoid) : Strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS : Carbon dioxide and carbon mono-oxide
HAZARDOUS POLYMERIZATION : Will not occur
7. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Keep away from potential ignition sources. Ventilate if in enclosed area.
Add absorbent and scoop into appropriate container.
Transfer to hood and evaporate or seal for waste disposal.
WASTE DISPOSAL : Destroy by approved incineration or deposit in approved landfill.
Must be in accordance with Federal, State and Local Laws and Regulations
8. SPECIAL PRECAUTIONS
RESPIRATORY: If threshold limit value is exceeded, use NIOH/MSHA approved
respirator for organic vapors.
EYEWEAR: Chemical splash goggles in compliance with OSHA regulations are
advised. Provide eye bath near work site.
CLOTHING/GLOVES: Wear resistant gloves such as rubber, neoprene or plastic.
VENTILATION: Provide sufficient mechanical (general and/or local exhaust)
ventilation to maintain exposure levels below TLVs.
Head office Tel: 82-31-355-9133 Fax : 82-31-355-9138 Address : 334-4 Ssangsongri Mado-myeon, Hwaseong-Si, Kyunggi-Do S.Korea
India Office 0422-231-1349 Hong Kong Office 852-2100-3205 China Office 86-755-2641-0271 Thailand Office 662- 643-9060
Malays ia Office 6 0 7- 5 1 2- 3 39 9 T aiwan Office 8 8 6- 2- 2 7 5 8- 0 9 2 0 UK o ffice 44 - 87 0- 4 5 9- 2673 Germany Office 49-745-162-4001
Italy Office 39-02-9904-6509 Finland Office 358-2630-5913 Spain Office 34-91-386-7139 USA Office 408-844-0400
MATERIAL SAFETY DATA SHEET
9. SPECIAL PRECATIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Observe precautions for a fume by reflow soldering. Keep container closed when not in use.
Store away from ignition sources, in a cool dry area with adequate ventilation.
Read all container labeling.
Avoid the use of metal drum spigots. Use Polyethylene, Polypropylene, or Teflon spigot.
OTHER PRECAUTIONS :
Containers : Since empty containers may retain product residues (vapor, liquid, or solid) all labeled hazard precautions must be
observed.
FOR INDUSTRIAL USE ONLY KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY.
10. Shipping, Receiving and Storage-Long term Storage and Handling
Shipping
Paste is refrigerated between 4 鈩? and 10 鈩? for a minimum of 12 hours prior
Pre-Shipment Preparation
to shipment. Paste is packed in Styrofoam containers with cold packs.
Unless a specific method is dictated by a customer, all solder pastes will be
Ship Method
shipped with overnight service
Shipping Temperatures Uncontrolled but should not exceed 35鈩? for more than a few hours.
Receiving
Average: 20~25鈩?
Recommended temperature of receiving
Maximum: Should not exceed 30鈩?
area
Minimum: No Recommendation
Time to transfer solder paste to permanent
Immediately after receiving
storage
Storage 鈥揕ong Term (Supply Area)
Long term storage area description Refrigerated 鈥揝yringes and cartridges should be stored tip down to avoid
separation
(Shelves, refrigerator, etc)
Containers for Jars, cartridges, or syringes
Similar lot #鈥檚 should be stored together, to avoid lot to lot mixing.
(Boxes, cooler, plastic carrier, etc)
Average: 4 to 10鈩?
Temperature of long term
Maximum: 10鈩?
storage area
Minimum: 4鈩?
Inventory description Solder paste should be inventoried using the FIFO (First In, First Out) system.
Refrigerated Shelf Life 6 Months
11. ADDITIONAL INFORMATION
CHRONIC TOXICITY : Overexposure to Polymer Alcohol has been suggested as a possible cause of kidney damage in humans.
Head office Tel: 82-31-355-9133 Fax : 82-31-355-9138 Address : 334-4 Ssangsongri Mado-myeon, Hwaseong-Si, Kyunggi-Do S.Korea
India Office 0422-231-1349 Hong Kong Office 852-2100-3205 China Office 86-755-2641-0271 Thailand Office 662- 643-9060
Malays ia Office 6 0 7- 5 1 2- 3 39 9 T aiwan Office 8 8 6- 2- 2 7 5 8- 0 9 2 0 UK o ffice 44 - 87 0- 4 5 9- 2673 Germany Office 49-745-162-4001
Italy Office 39-02-9904-6509 Finland Office 358-2630-5913 Spain Office 34-91-386-7139 USA Office 408-844-0400
|