Welcome to
Hastings Plastics
Material Safety Data Sheets for Mold Making
SILICONE COATING RUBBER. MOLDKOTE 1900-2A
SILICONE COATING RUBBER. MOLDKOTE 1900-2A SPECIAL
PRIMER FOR SILICONE RUBBER. MOLDKOTE 1900-3
MOLD SEALER. MOLDKOTE 1906
*Click on underlined link to go to MSDS*
You can print the data by selecting the sheets you want and printing that selection.
PRODUCT DATA
HASTINGS MSDS RTV-1900-2A
PLASTICS REVISED 09/21/01
REPLACES 10/15/98
COMPANY
1704 Colorado Ave. Santa Monica, CA 90404 310-829-3449 FAX 310-828-6820
BACK TO INDEX
MOLDKOTE RTV 1900-2A
SECTION I - PRODUCT IDENTIFICATION
MANUFACTURER'S NAME - HASTINGS PLASTICS COMPANY
PRODUCT INFO/ SALES - (310) 829-3449
EMERGENCY PHONE NUMBER - (800) 424-9300
PRODUCT NAME - Moldkote RTV-1900-2A
CHEMICAL FAMILY - Moisture Curing Silicone Sealant
CHEMICAL NAME AND
SYNONYMS - N/A
FORMULA - N/A
HMIS:
Health - 3
Flam m ability - 3
Reactivity - 1
Person Protective Equipm ent - X
SECTION II - HAZARDOUS INGREDIENTS
(1) (2) (3)
COM PONENTS CAS NO. % PEL TLV STEL
PETROLEUM NAPHTHA DISTILLATE 64742-89-8 10-15 300 ppm 300 ppm 400
NAPHTHA (petroleum ) HYDRO TREATED 64742-49-0 45-50 300 ppm 300ppm none
SILICONE DIOXIDE (am orphous) N/A Trace 20 Mppcf 20 Mppcf
CYCLOHEXYLAMINE 108-91-8 3 none none none
N.E. = NOT ESTABLISHED
(1) 29 CFR 1910.1000.
(2) The Am erican Conference of Governm ental Industrial Hygienists (ACGIH) (1984) threshold lim it values for chem ical
substance and physical agents in the work environm ent and biological exposure indices with intended changes for 1984-
1985. (ACGIH) Cincinnati, Ohio.
(3) Sam e References as # (2).
This m aterial is a dispersion which contains petroleum distillate (naphtha) and silicon dioxide and releases
cYCLOHEXYLAMINE upon curing. The specific chem ical identity of the ingredients of this form ulation are considered a
trade secret.
SECTION III - PHYSICAL DATA
APPEARANCE AND ODOR - Viscous liquid. Odor of naphtha.
BOILING POINT - 244/F (118/C).
VAPOR PRESSURE (68 0 F, m m Hg) - 26
VAPOR DENSITY (Air = 1) - 4
SPECIFIC GRAVITY (W ater = 1) - 0.87
SOLUBILITY IN W ATER - Negligible.
PERCENT VOLATILE (By Volum e) - 60
EVAPORATION RATE (Ether = 1) - 0.12
FLASH POINT (Method Used) - 69/F or 21.6/C (Pensky-Martens C. C.).
FLAMMABLE LIMITS (% By Volum e In Air) - LEL: 0.9 UEL: 6.7
V.O.C. CONTENT - 494 Gram s per Liter
M OLDKOTE RTV 1900-2A M ATERIAL SAFETY DATA SHEET PAGE 2 OF 21
SECTION IV - FIRE AND HAZARD EXPLOSION DATA
This product is considered flam m able and is a fire hazard. It supports com bustion and decom poses under fire
conditions to give off toxic m aterials. Do not uses welding or cutting torch on or near any container of this m aterial,
even if em pty, because an explosion could occur. Do not use, pour, spill, or store near heat, spark sources, or open
flam es. Com bustion products of the uncured rubber are toxic. There are no unusual hazards with the cured
m aterial.
FIRE FIGHTING PROCEDURES:
Use standard fire fighting techniques to extinguish fires involving this m aterial. Use water spray, dry chem icals, or
carbon dioxide. Vapors from com bustion are toxic and severely irritating to the respiratory tract and m ay cause
breathing difficulty. As in any fire, prevent hum an exposure to fire, sm oke, fum es, or products of com bustion.
Evacuate non-essential personnel from the fire area. Fire fighters should wear full-face, self-contained breathing
apparatus and im pervious protective clothing. If not leaking, keep fire-exposed containers cool with a water spray to
prevent rupture due to excessive heat. High pressure water hose m ay spread product from broken containers
increasing contam ination or fire hazard. Vapors from com bustion of the uncured m aterial are toxic.
COMBUSTION BY-PRODUCTS:
Carbon Monoxide
Carbon Dioxide
Silicon Dioxide
Form aldehyde
Various Hydrocarbon Fragm ents
SECTION V - HEALTH HAZARD DATA
EFFECTS OF OVEREXPOSURE:
ANIMAL TOXICITY (Oral, LD 50): 4640 m g/kg in rats.
EYES(rabbit): Extrem ely irritating.
SKIN CONTACT(rabbit): Severe irritant.
SECTION VI - HUM AN HEALTH EFFECTS DATA
EFFECTS OF OVEREXPOSURE:
PRINCIPLE ROUTES OF EXPOSURE: Skin contact and inhalation.
SKIN CONTACT: May cause irritation.
EYE CONTACT: May cause burns.
INHALATION: Vapors m ay cause respiratory irritation.
TARGET ORGANS EFFECTED: Brain and Nervous System
REPRODUCTIVE TOXINS: This m aterial does not contain any reproductive toxins over 1%
This m aterial does not contain any reproductive toxins over 0.1%
MATERIALS OVER 0.1% BY W EIGHT LISTED AS A CARCINOGEN:
There are no carcinogenic ingredients present at over 0.1% in this m aterial.
OTHER PRECAUTIONS:
There are no data available which address m edical conditions which are generally recognized as being aggravated
by exposure to this product. (Reader should consult Section IV Health Effects Data for effects observed in
experim ental anim als under controlled laboratory conditions using this product). This product contains am orphous
silicon dioxide, but due to the physical nature of this m aterial, inhalation of silicon dioxide dust is not anticipated.
M OLDKOTE RTV 1900-2A M ATERIAL SAFETY DATA SHEET PAGE 3 OF 21
This product contains a petroleum distillate. Exposure to the vapors of this m aterial m ay cause central nervous
system depression. Severe exposure has been known to cause irritation of the respiratory tract. Signs and
sym ptom s of overexposure include dizziness, drowsiness, headache, nausea, dyspnea, and derm atitis (1). This
product releases cYCLOHEXYLAMINE upon m oisture curing. Exposure to cYCLOHEXYLAMINE m ay cause
irritation of the eyes, m ucous m em branes, and skin.
OTHER EXPOSURE LIMITS:
CHEM ICAL TYPE EXPOSURE GUIDELINES
Silica Am orphous, fum ed REL 6m g/m 3
Methanol Short-term Exposure Lim it (STEL) 250 ppm
SECTION VII - EM ERGENCY AND FIRST AID PROCEDURES
EYE CONTACT:
In case of contact, im m ediately flush eyes with large am ounts of running water for at least 15 m inutes while
rem oving contam inated clothing and shoes. Hold eyelids apart to ensure rinsing of the entire surface of the eye and
lids with water. Get m edical attention im m ediately. W ash clothing before reuse.
SKIN CONTACT:
Flush skin well with water and wash well with water and soap. Obtain m edical attention if irritation occurs.
INGESTION:
If swallowed, give several glasses of water but do not induce vom iting. If vom iting does occur, give fluids again.
Have m edical personnel determ ine if vom iting or evacuation of stom ach is necessary. Do not give anything
by m outh to an unconscious or convulsing person.
INHALATION:
If inhaled, rem ove to fresh air. Seek m edical attention if respiratory irritation occurs or breathing becom es difficult.
SECTION VIII - SPECIAL PROTECTION INFORM ATION
GENERAL:
The recom m endations described in this section are provided as general guidance for m inim izing exposure when
handling this product. Because conditions of use will vary depending upon custom er applications, specific safe
handling procedures should be developed by a person knowledgeable of the intended use, conditions, and
equipm ent. During the developm ent of safe handling procedures, consideration should be given to the need for
cleaning of equipm ent and piping system s to render them non- hazardous before m aintenance and repair activities
are perform ed.
ENGINEERING CONTROLS:
In those cases where engineering controls are indicated by the use conditions, the following traditional exposure
control techniques m ay be used to effectively m inim ize em ployee exposure: local exhaust ventilation, enclosed
system design, process isolation, and rem ote control in com bination with appropriate use of personal protective
equipm ent.
INGESTION:
All food should be kept in a separate area away from the storage/use location. Eating, drinking, and sm oking should
be prohibited in areas where there is a potential for significant exposure to this m aterial. Before eating, hands and
face should be thoroughly washed.
SKIN CONTACT:
Skin contact should be m inim ized through the use of gloves and suitable long-sleeved clothing selected with regard
for use condition exposure potential.
EYE CONTACT:
Eye contact should be avoided through the use of chem ical safety glasses, goggles or a face shield selected with
regard for use condition exposure potential.
M OLDKOTE RTV 1900-2A M ATERIAL SAFETY DATA SHEET PAGE 4 OF 21
INHALATION:
If use conditions generate airborne contam ination, the m aterial should be handled in an open (e.g. outdoor) or well
ventilated area. W here adequate ventilation is not available, use NIOSH-approved organic vapor respirators with
dust, m ist, and fum e filter to reduce exposure. W here exposure potential under the use conditions necessitates a
higher level of protection, use a positive-pressure, air-supplied respirator.
EXPOSURE LIMITS:
No exposure lim it has been established for this product, however, the following exposure lim its apply for product
constituents:
SECTION IX - REACTIVITY DATA
STABILITY - Stable under norm al conditions of use.
HAZARDOUS POLYMERIZATION - Hazardous polym erization cannot occur.
GENERAL - Hydrolysis slowly at am bient tem peratures, when exposed to m oist air, to
release cYCLOHEXYLAMINE. Solvent evaporation will also take place if
open to the air. Keep container closed to prevent exposure to air.
CONDITIONS TO AVOID - Avoid contact with incom patible m aterials.
SECTION X - SPILL AND LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Make sure all personnel involved in the spill clean-up follow good industrial hygiene practices (refer to SECTION VII
- Special Protection Inform ation). Any person entering either a significant spill area or an unknown concentration of
vapor or aerosol should use a positive-pressure, self-contained breathing apparatus, or a positive-pressure,
supplied-air respirator with escape pack. Sm all spills can be handled routinely. Use adequate ventilation and wear
a NIOSH-approved respirator with dust, m ist, and fum e filter to prevent inhalation exposure. W ear protective
clothing to prevent skin and eye contact. Use the following procedures: Absorb spill with sand or Fuller's earth.
Sweep up and place in an appropriate chem ical waste container. Flush spill area with water. Observe all local,
state, and federal laws and regulations regarding disposal, spill, clean-up, rem oval, or discharge. In case of spill
em ergency, day or night, call CHEMTREC (800-424-9300).
W ASTE DISPOSAL METHOD:
Material that cannot be used or chem ically reprocessed should be disposed of at an approved facility in accordance
with any applicable regulations under the Resource Conservation and Recovery Act. NOTE: State and local
regulations m ay be m ore stringent than Federal.
DISPOSAL OF CONTAINER:
Dispose of em pty containers according to any applicable regulations under the Resource Conservation and
Recovery Act. NOTE: State and local regulations m ay be m ore stringent than federal.
CORROSIVITY TO MATERIALS OF CONSTRUCTION:
Not recom m ended for use with acrylic or polycarbonate substrates.
RCRA W ASTE CLASSIFICATION:
D001 (Ignitable)
D002 (Corrosive)
This classification applies only to the m aterial as it was originally produced.
SECTION XI - SHIPPING AND STORAGE INFORM ATION
GENERAL PRECAUTIONS:
Containers should be stored in a cool, dry, well ventilated area away from flam m able m aterials and sources of heat
or flam e. Store away from food stuffs or anim al feed. Exercise due caution to prevent dam age to or leakage from
the container. Do not store near strong acids or oxidizing agents.
M OLDKOTE RTV 1900-2A M ATERIAL SAFETY DATA SHEET PAGE 5 OF 21
Prolonged storage at elevated tem peratures should be avoided. Care should be taken to prevent m oisture
condensation on the container. Keep away from heat, sparks, or open flam e. Never use welding or cutting torch on
or near any container (even em pty) as an explosion can occur.
D.O.T. HAZARD NAME - COATING SOLUTION
D.O.T. I.D.# - UN 1139, PGIII
D.O.T. HAZARD CLASS - Flam m able liquid
PRIMARY HAZARD CLASS: - 3
UNITED STATES
TSCA INVENTORY STATUS:
This m aterial or its com ponents are listed on or are in com pliance with the requirem ents of the TSCA Chem ical
Substance Inventory.
TSCA 12(b) EXPORT NOTIFICATION:
12(b) CHEM ICAL REPORTING REQUIRED UNDER TSCA
This m aterial does not contain any TSCA 12(b) regulated chem icals.
CW A 307 PRIORITY POLLUTANTS:
Benzene, m ethyl-
CW A 311 HAZARDOUS SUBSTANCES:
1,2-Ethane diam ine / Benzene, m ethyl-
SDW A MCL CHEMICALS:
Benzene, m ethyl-
HAPS:
Methanol / Benzene, m ethyl-
CERCLA REGULATED CHEMICALS:
CHEM ICAL RQ
This m aterial does not contain any CERCLA regulated chem icals.
SARA 302 EHS CHEMICALS:
CHEM ICAL RQ TPQ
This m aterial does not contain any SARA extrem ely hazardous substances.
SARA 311/312 HAZARD CLASS:
Im m ediate (acute) health hazard.
Delayed (chronic) health hazard.
Fire hazard.
SARA 313 CHEMICALS:
CHEM ICAL CAS No. LOW ER LIM IT W T. % UPPER LIM IT W T. %
This chem ical does not contain any SARA 313 chem icals above de minimus levels.
STATE REGULATIONS
MASSACHUSETTS SUBSTANCE LIST:
Silica am orphous, fum ed
PENNSYLVANIA RIGHT-TO-KNOW HAZARDOUS SUBSTANCE LIST:
Silica am orphous, fum ed
NEW JERSEY RIGHT-TO-KNOW HAZARDOUS SUBSTANCE LIST:
Silica am orphous, fum ed
CALIFORNIA PROPOSITION 65 CARCINOGENS:
This m aterial does not contain any chem icals known to the State of California to cause cancer.
M OLDKOTE RTV 1900-2A M ATERIAL SAFETY DATA SHEET PAGE 6 OF 21
CALIFORNIA PROPOSITION 65 REPRODUCTIVE TOXINS:
Benzene, m ethyl-
HMIS
Health 3
Fire Hazard 3
Reactivity 1
Personal Protection X
CANADA
This product has been classified in accordance with the Hazard criteria of the CPR and the MSDS contains all the
inform ation required by the CPR.
W HMIS HAZARD CLASSES:
B2. D2B. E.
DSL STATUS:
This m aterial or its com ponents are listed on the Canadian Dom estic Substance List.
NON-DSL CHEMICALS:
CHEM ICAL CAS No. W T. %
This m aterial does not contain any non-DSL chem icals.
CANADIAN INGREDIENT DISCLOSURE LIST:
Silica am orphous, fum ed
OTHER INTERNATIONAL INVENTORIES:
EUROPE / EINECS:
Yes - This m aterial or its com ponents are listed on or are in com pliance with EINECS.
JAPAN / MITI/ENCS:
Com pliance with this inventory has not been determ ined.
AUSTRALIA / AICS:
Yes - This m aterial or its com ponents are listed on AICS.
KOREA / ECL:
Yes - This m aterial or its com ponents are listed on Korean ECL.
PHILIPPINES / PICCS:
Yes - This m aterial or its com ponents are listed on PICCS.
DISCLAIM ER OF LIABILITY
As the conditions or m ethods of use are beyond our control, we do not
assum e any responsibility and expressly disclaim liability for any use of
this m aterial. Inform ation contained herein is believed to be true and
accurate but all statem ents are m ade without warranty, express or
im plied, regarding the accuracy of the inform ation, the hazards
connected with the use of the m aterial or the results to be obtained from
the use thereof. It is the user's obligation to determ ine the conditions of
safe use and the suitability of the m aterial for the user's purpose.
Prepared By: Joe Morales
Revised By: Erik Ricci 09/21/01
F#170-21A
PRODUCT DATA
HASTINGS MSDS RTV-1900-2A
PLASTICS SPECIAL
REVISED 09/21/01
COMPANY REPLACES 10/15/98
1704 Colorado Ave. Santa Monica, CA 90404 310-829-3449 FAX 310-828-6820
BACK TO INDEX
MOLDKOTE RTV 1900-2A SPECIAL
SECTION I - PRODUCT IDENTIFICATION
MANUFACTURER'S NAME - HASTINGS PLASTICS COMPANY
PRODUCT INFO/ SALES - (310) 829-3449
EMERGENCY PHONE NUMBER - (800) 424-9300
PRODUCT NAME - Moldkote RTV-1900-2A Special
CHEMICAL FAMILY - Moisture Curing Silicone Sealant
CHEMICAL NAME AND
SYNONYMS - N/A
FORMULA - N/A
HMIS:
Health - 3
Flam m ability - 3
Reactivity - 1
Person Protective Equipm ent - X
SECTION II - HAZARDOUS INGREDIENTS
(1) (2) (3)
COM PONENTS CAS NO. % PEL TLV STEL
PETROLEUM NAPHTHA DISTILLATE 64742-89-8 10-15 300 ppm 300 ppm 400
NAPHTHA (petroleum ) HYDRO TREATED 64742-49-0 45-50 300 ppm 300ppm none
SILICONE DIOXIDE (am orphous) N/A Trace 20 Mppcf 20 Mppcf
CYCLOHEXYLAMINE 108-91-8 3 none none none
N.E. = NOT ESTABLISHED
(1) 29 CFR 1910.1000.
(2) The Am erican Conference of Governm ental Industrial Hygienists (ACGIH) (1984) threshold lim it values for chem ical
substance and physical agents in the work environm ent and biological exposure indices with intended changes for 1984-
1985. (ACGIH) Cincinnati, Ohio.
(3) Sam e References as # (2).
This m aterial is a dispersion which contains petroleum distillate (naphtha) and silicon dioxide and releases
CYCLOHEXYLAMINE upon curing. The specific chem ical identity of the ingredients of this form ulation are considered a
trade secret.
SECTION III - PHYSICAL DATA
APPEARANCE AND ODOR - Viscous liquid. Odor of naphtha.
BOILING POINT - 244/F (118/C).
VAPOR PRESSURE (68 0 F, m m Hg) - 26
VAPOR DENSITY (Air = 1) -4
SPECIFIC GRAVITY (W ater = 1) - 0.87
SOLUBILITY IN W ATER - Negligible.
PERCENT VOLATILE (By Volum e) - 40
EVAPORATION RATE (Ether = 1) - 0.12
FLASH POINT (Method Used) - 69/F or 21.6/C (Pensky-Martens C. C.).
FLAMMABLE LIMITS (% By Volum e In Air) - LEL: 0.9 UEL: 6.7
V.O.C. CONTENT - 329 Gram s per Liter
M OLDKOTE RTV 1900-2A SPECIAL M ATERIAL SAFETY DATA SHEET PAGE 9 OF 21
SECTION IV - FIRE AND HAZARD EXPLOSION DATA
This product is considered flam m able and is a fire hazard. It supports com bustion and decom poses under fire
conditions to give off toxic m aterials. Do not uses welding or cutting torch on or near any container of this m aterial,
even if em pty, because an explosion could occur. Do not use, pour, spill, or store near heat, spark sources, or open
flam es. Com bustion products of the uncured rubber are toxic. There are no unusual hazards with the cured
m aterial.
FIRE FIGHTING PROCEDURES:
Use standard fire fighting techniques to extinguish fires involving this m aterial. Use water spray, dry chem icals, or
carbon dioxide. Vapors from com bustion are toxic and severely irritating to the respiratory tract and m ay cause
breathing difficulty. As in any fire, prevent hum an exposure to fire, sm oke, fum es, or products of com bustion.
Evacuate non-essential personnel from the fire area. Fire fighters should wear full-face, self-contained breathing
apparatus and im pervious protective clothing. If not leaking, keep fire-exposed containers cool with a water spray to
prevent rupture due to excessive heat. High pressure water hose m ay spread product from broken containers
increasing contam ination or fire hazard. Vapors from com bustion of the uncured m aterial are toxic.
COMBUSTION BY-PRODUCTS:
Carbon Monoxide
Carbon Dioxide
Silicon Dioxide
Form aldehyde
Various Hydrocarbon Fragm ents
SECTION V - HEALTH HAZARD DATA
EFFECTS OF OVEREXPOSURE:
ANIMAL TOXICITY (Oral, LD 50): 4640 m g/kg in rats.
EYES(rabbit): Extrem ely irritating.
SKIN CONTACT(rabbit): Severe irritant.
SECTION VI - HUM AN HEALTH EFFECTS DATA
EFFECTS OF OVEREXPOSURE:
PRINCIPLE ROUTES OF EXPOSURE: Skin contact and inhalation.
SKIN CONTACT: May cause irritation.
EYE CONTACT: May cause burns.
INHALATION: Vapors m ay cause respiratory irritation.
TARGET ORGANS EFFECTED: Brain and Nervous System
REPRODUCTIVE TOXINS: This m aterial does not contain any reproductive toxins over 1%
This m aterial does not contain any reproductive toxins over 0.1%
MATERIALS OVER 0.1% BY W EIGHT LISTED AS A CARCINOGEN:
There are no carcinogenic ingredients present at over 0.1% in this m aterial.
OTHER PRECAUTIONS:
There are no data available which address m edical conditions which are generally recognized as being aggravated
by exposure to this product. (Reader should consult Section IV Health Effects Data for effects observed in
experim ental anim als under controlled laboratory conditions using this product). This product contains am orphous
silicon dioxide, but due to the physical nature of this m aterial, inhalation of silicon dioxide dust is not anticipated.
M OLDKOTE RTV 1900-2A SPECIAL M ATERIAL SAFETY DATA SHEET PAGE 10 OF 21
This product contains a petroleum distillate. Exposure to the vapors of this m aterial m ay cause central nervous
system depression. Severe exposure has been known to cause irritation of the respiratory tract. Signs and
sym ptom s of overexposure include dizziness, drowsiness, headache, nausea, dyspnea, and derm atitis (1). This
product releases cYCLOHEXYLAMINE upon m oisture curing. Exposure to cYCLOHEXYLAMINE m ay cause
irritation of the eyes, m ucous m em branes, and skin.
OTHER EXPOSURE LIMITS:
CHEM ICAL TYPE EXPOSURE GUIDELINES
Silica Am orphous, fum ed REL 6m g/m 3
Methanol Short-term Exposure Lim it (STEL) 250 ppm
SECTION VII - EM ERGENCY AND FIRST AID PROCEDURES
EYE CONTACT:
In case of contact, im m ediately flush eyes with large am ounts of running water for at least 15 m inutes while
rem oving contam inated clothing and shoes. Hold eyelids apart to ensure rinsing of the entire surface of the eye and
lids with water. Get m edical attention im m ediately. W ash clothing before reuse.
SKIN CONTACT:
Flush skin well with water and wash well with water and soap. Obtain m edical attention if irritation occurs.
INGESTION:
If swallowed, give several glasses of water but do not induce vom iting. If vom iting does occur, give fluids again.
Have m edical personnel determ ine if vom iting or evacuation of stom ach is necessary. Do not give anything
by m outh to an unconscious or convulsing person.
INHALATION:
If inhaled, rem ove to fresh air. Seek m edical attention if respiratory irritation occurs or breathing becom es difficult.
SECTION VIII - SPECIAL PROTECTION INFORM ATION
GENERAL:
The recom m endations described in this section are provided as general guidance for m inim izing exposure when
handling this product. Because conditions of use will vary depending upon custom er applications, specific safe
handling procedures should be developed by a person knowledgeable of the intended use, conditions, and
equipm ent. During the developm ent of safe handling procedures, consideration should be given to the need for
cleaning of equipm ent and piping system s to render them non- hazardous before m aintenance and repair activities
are perform ed.
ENGINEERING CONTROLS:
In those cases where engineering controls are indicated by the use conditions, the following traditional exposure
control techniques m ay be used to effectively m inim ize em ployee exposure: local exhaust ventilation, enclosed
system design, process isolation, and rem ote control in com bination with appropriate use of personal protective
equipm ent.
INGESTION:
All food should be kept in a separate area away from the storage/use location. Eating, drinking, and sm oking should
be prohibited in areas where there is a potential for significant exposure to this m aterial. Before eating, hands and
face should be thoroughly washed.
SKIN CONTACT:
Skin contact should be m inim ized through the use of gloves and suitable long-sleeved clothing selected with regard
for use condition exposure potential.
EYE CONTACT:
Eye contact should be avoided through the use of chem ical safety glasses, goggles or a face shield selected with
regard for use condition exposure potential.
M OLDKOTE RTV 1900-2A SPECIAL M ATERIAL SAFETY DATA SHEET PAGE 11 OF 21
INHALATION:
If use conditions generate airborne contam ination, the m aterial should be handled in an open (e.g. outdoor) or well
ventilated area. W here adequate ventilation is not available, use NIOSH-approved organic vapor respirators with
dust, m ist, and fum e filter to reduce exposure. W here exposure potential under the use conditions necessitates a
higher level of protection, use a positive-pressure, air-supplied respirator.
EXPOSURE LIMITS:
No exposure lim it has been established for this product, however, the following exposure lim its apply for product
constituents:
SECTION IX - REACTIVITY DATA
STABILITY - Stable under norm al conditions of use.
HAZARDOUS POLYMERIZATION - Hazardous polym erization cannot occur.
GENERAL - Hydrolysis slowly at am bient tem peratures, when exposed to m oist air, to
release CYCLOHEXYLAMINE. Solvent evaporation will also take place if
open to the air. Keep container closed to prevent exposure to air.
CONDITIONS TO AVOID - Avoid contact with incom patible m aterials.
SECTION X - SPILL AND LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Make sure all personnel involved in the spill clean-up follow good industrial hygiene practices (refer to SECTION VII
- Special Protection Inform ation). Any person entering either a significant spill area or an unknown concentration of
vapor or aerosol should use a positive-pressure, self-contained breathing apparatus, or a positive-pressure,
supplied-air respirator with escape pack. Sm all spills can be handled routinely. Use adequate ventilation and wear
a NIOSH-approved respirator with dust, m ist, and fum e filter to prevent inhalation exposure. W ear protective
clothing to prevent skin and eye contact. Use the following procedures: Absorb spill with sand or Fuller's earth.
Sweep up and place in an appropriate chem ical waste container. Flush spill area with water. Observe all local,
state, and federal laws and regulations regarding disposal, spill, clean-up, rem oval, or discharge. In case of spill
em ergency, day or night, call CHEMTREC (800-424-9300).
W ASTE DISPOSAL METHOD:
Material that cannot be used or chem ically reprocessed should be disposed of at an approved facility in accordance
with any applicable regulations under the Resource Conservation and Recovery Act. NOTE: State and local
regulations m ay be m ore stringent than Federal.
DISPOSAL OF CONTAINER:
Dispose of em pty containers according to any applicable regulations under the Resource Conservation and
Recovery Act. NOTE: State and local regulations m ay be m ore stringent than federal.
CORROSIVITY TO MATERIALS OF CONSTRUCTION:
Not recom m ended for use with acrylic or polycarbonate substrates.
RCRA W ASTE CLASSIFICATION:
D001 (Ignitable)
D002 (Corrosive)
This classification applies only to the m aterial as it was originally produced.
SECTION XI - SHIPPING AND STORAGE INFORM ATION
GENERAL PRECAUTIONS:
Containers should be stored in a cool, dry, well ventilated area away from flam m able m aterials and sources of heat
or flam e. Store away from food stuffs or anim al feed. Exercise due caution to prevent dam age to or leakage from
the container. Do not store near strong acids or oxidizing agents.
M OLDKOTE RTV 1900-2A SPECIAL M ATERIAL SAFETY DATA SHEET PAGE 12 OF 21
Prolonged storage at elevated tem peratures should be avoided. Care should be taken to prevent m oisture
condensation on the container. Keep away from heat, sparks, or open flam e. Never use welding or cutting torch on
or near any container (even em pty) as an explosion can occur.
D.O.T. HAZARD NAME - COATING SOLUTION
D.O.T. I.D.# - UN 1139 , PGIII
D.O.T. HAZARD CLASS - Flam m able liquid
PRIMARY HAZARD CLASS: - 3
UNITED STATES
TSCA INVENTORY STATUS:
This m aterial or its com ponents are listed on or are in com pliance with the requirem ents of the TSCA Chem ical
Substance Inventory.
TSCA 12(b) EXPORT NOTIFICATION:
12(b) CHEM ICAL REPORTING REQUIRED UNDER TSCA
This m aterial does not contain any TSCA 12(b) regulated chem icals.
CW A 307 PRIORITY POLLUTANTS:
Benzene, m ethyl-
CW A 311 HAZARDOUS SUBSTANCES:
1,2-Ethane diam ine / Benzene, m ethyl-
SDW A MCL CHEMICALS:
Benzene, m ethyl-
HAPS:
Methanol / Benzene, m ethyl-
CERCLA REGULATED CHEMICALS:
CHEM ICAL RQ
This m aterial does not contain any CERCLA regulated chem icals.
SARA 302 EHS CHEMICALS:
CHEM ICAL RQ TPQ
This m aterial does not contain any SARA extrem ely hazardous substances.
SARA 311/312 HAZARD CLASS:
Im m ediate (acute) health hazard.
Delayed (chronic) health hazard.
Fire hazard.
SARA 313 CHEMICALS:
CHEM ICAL CAS No. LOW ER LIM IT W T. % UPPER LIM IT W T. %
This chem ical does not contain any SARA 313 chem icals above de minimus levels.
STATE REGULATIONS
MASSACHUSETTS SUBSTANCE LIST:
Silica am orphous, fum ed
PENNSYLVANIA RIGHT-TO-KNOW HAZARDOUS SUBSTANCE LIST:
Silica am orphous, fum ed
NEW JERSEY RIGHT-TO-KNOW HAZARDOUS SUBSTANCE LIST:
Silica am orphous, fum ed
CALIFORNIA PROPOSITION 65 CARCINOGENS:
This m aterial does not contain any chem icals known to the State of California to cause cancer.
M OLDKOTE RTV 1900-2A SPECIAL M ATERIAL SAFETY DATA SHEET PAGE 13 OF 21
CALIFORNIA PROPOSITION 65 REPRODUCTIVE TOXINS:
Benzene, m ethyl-
HMIS
Health 3
Fire Hazard 3
Reactivity 1
Personal Protection X
CANADA
This product has been classified in accordance with the Hazard criteria of the CPR and the MSDS contains all the
inform ation required by the CPR.
W HMIS HAZARD CLASSES:
B2. D2B. E.
DSL STATUS:
This m aterial or its com ponents are listed on the Canadian Dom estic Substance List.
NON-DSL CHEMICALS:
CHEM ICAL CAS No. W T. %
This m aterial does not contain any non-DSL chem icals.
CANADIAN INGREDIENT DISCLOSURE LIST:
Silica am orphous, fum ed
OTHER INTERNATIONAL INVENTORIES:
EUROPE / EINECS:
Yes - This m aterial or its com ponents are listed on or are in com pliance with EINECS.
JAPAN / MITI/ENCS:
Com pliance with this inventory has not been determ ined.
AUSTRALIA / AICS:
Yes - This m aterial or its com ponents are listed on AICS.
KOREA / ECL:
Yes - This m aterial or its com ponents are listed on Korean ECL.
PHILIPPINES / PICCS:
Yes - This m aterial or its com ponents are listed on PICCS.
DISCLAIM ER OF LIABILITY
As the conditions or m ethods of use are beyond our control, we do not
assum e any responsibility and expressly disclaim liability for any use of
this m aterial. Inform ation contained herein is believed to be true and
accurate but all statem ents are m ade without warranty, express or
im plied, regarding the accuracy of the inform ation, the hazards
connected with the use of the m aterial or the results to be obtained from
the use thereof. It is the user's obligation to determ ine the conditions of
safe use and the suitability of the m aterial for the user's purpose.
Prepared By: Joe Morales
Revised By: Erik Ricci 09/21/01
F#170-21A
PRODUCT DATA
HASTINGS MSDS 1900-3
PLASTICS *Revised 12/8/98
REPLACED 3/24/93
COMPANY
1704 Colorado Ave. Santa Monica, CA 90404 310-829-3449 FAX 310-828-6820
BACK TO INDEX
MOLDKOTE 1900-3 PRIMER
SECTION I - PRODUCT IDENTIFICATION
MANUFACTURER'S NAME - HASTINGS PLASTICS COMPANY
EMERGENCY PHONE NUMBER - (800)424-9300
PRODUCT NAME - Moldkote 1900-3 Primer
GENERIC DESCRIPTION - Organ silicate in Solvent
CAS NUMBER - Mixture
RCRA HAZARD CLASS
(40CFR 261) - If discarded: ignitable (DOO1)
E.P.A. PRIORITY
(40CFR 122.53) - None
POLLUTANTS:
NFPA (National Fire
Protection Association) - 704
HEALTH (NFPA) -2
FLAMMABILITY (NFPA) -3
REACTIVITY (NFPA) -0
SECTION II - HAZARDOUS INGREDIENTS
COMPONENTS CAS NO. % EXPOSURE LIMITS
NAPHTHA, PETROLEUM, 064742898 85 OBSERVE VM & P NAPHTHA LIMITS
LIGHT ALIPHATIC OSHA PEL: TWA 300 PPM, STEL 400
PPM
ACGIH TLV: TWA 300 PPM
TETRA (2-METHOXYETHOXY)- 002157451 5 SEE COMMENT 1.
SILANE
TETRAPROPYL 000682019 5 SEE COMMENT 2.
ORTHOSILICATE
TETRABUTYL TITANATE 005593704 5 SEE COMMENT 3.
COMMENT 1: OBSERVE LIMITS FOR 2-METHOXYETHANOL, FORMED ON EXPOSURE TO
WATER OR HUMID AIR. OSHA PEL-SKIN: TWA 25 PPM.
ACGIH TLV-SKIN: TWA 5 PPM.
COMMENT 2: OBSERVE LIMITS FOR N-PROPYL ALCOHOL, FORMED ON EXPOSURE TO
WATER OR HUMID AIR. OSHA PEL: TWA 200PPM, STEL 250 PPM.
ACGIH TLV-SKIN: TWA 200PPM, STEL 250 PPM
COMMENT 3: OBSERVE LIMITS FOR N-BUTYL ALCOHOL, FORMED ON EXPOSURE TO WATER
OR HUMID AIR. OSHA PEL-SKIN AND ACGIH TLV-SKIN: 50 PPM CEILING.
SECTION III - EFFECTS OF OVEREXPOSURE
EYES: Direct contact irritates slightly with redness and swelling. (Over)
SKIN: A single relatively short exposure (less than 24 hours) irritates. Repeated
MOLDKOTE 1900-3 MATERIAL SAFETY DATA SHEET PAGE 15 OF 21
prolonged contact (24 to 48 hours) irritates seriously, may burn mildly.
INHALATION: Short vapor exposure may cause drowsiness and irritate nose and throat.
Degree of effects depends on concentration and length of exposure.
ORAL: Small amounts transferred to the mouth by fingers during use, etc., should not injure. Swallowing large
amounts may injure slightly.
INHALING LIQUID WHILE VOMITING CAN INJURE LUNGS SERIOUSLY.
COMMENTS: PROLONGED OVEREXPOSURE TO 2-METHOXYETHANOL, FORMED ON EXPOSURE
TO WATER OR HUMID AIR, MAY CAUSE BIRTH DEFECTS BASED ON ANIMAL DATA.
SECTION IV - EMERGENCY & FIRST AID PROCEDURES
INHALATION: Remove to fresh air. Obtain immediate medical attention.
EYE CONTACT: Flush with water.
SKIN CONTACT: Wipe off and flush with water for 15 minutes. Get medical attention if irritation develops.
ORAL: DO NOT INDUCE VOMITING. Obtain immediate medical attention.
COMMENTS: Inhaling liquid while vomiting can injure lungs seriously. If vomiting occurs, keep head below
hips to prevent aspiration of liquid into lungs.
SECTION V - FIRE AND HAZARD EXPLOSION DATA
FLASH POINT /F
- 63 /F/17 /C (Closed Cup).
(Method Used)
AUTOIGNITION - Not determined.
FLAMMABLE LIMITS
(In Air % LEL) - LOWER: Not determined.
UPPER: Not determined.
EXTINGUISHING MEDIA - Water fog, CO2, dry chemical, foam.
SPECIAL FIRE FIGHTING PROCEDURES: Self contained breathing apparatus and protective clothing
should be worn in fighting fires involving chemicals.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Vapors are heavier than air and can travel along the
ground to remote ignition sources.
COMMENTS: Static electricity may accumulate and ignite vapors. Prevent a possible fire hazard by suitable
means, such as, bonding and grounding, inert gas purge, vapor dilution, and the like.
SECTION VI - PHYSICAL DATA
BOILING POINT
210 /F/99 /C.
(760 mm HG) -
SPECIFIC GRAVITY
(At 77 /F/25 /C) - .76
MELTING POINT - N/A.
VAPOR PRESSURE
(At 77 /F/25 / C) - 25 MM
VAPOR DENSITY
(Air = 1 AT 77 /F/25 /C) - Approx. 3.8 (next page)
PERCENT VOLATILE
(By Volume) - Approx. 95%
EVAPORATION RATE
MOLDKOTE 1900-3 MATERIAL SAFETY DATA SHEET PAGE 16 OF 21
(Ether = 1) - N.D.
SOLUBILITY IN WATER - N.D.
APPEARANCE, COLOR
AND ODOR - Liquid, red, solvent odor.
VOC CONTENT - 741 Grams per Liter
SECTION VII - REACTIVITY DATA
STABILITY - Stable.
HAZARDOUS
POLYMERIZATION - Will not occur.
INCOMPATIBILITY - Oxidizing material can cause a reaction. Moisture or humid air.
CONDITIONS TO AVOID - Exposure to moisture or humid air until ready to use.
HAZARDOUS DECOMPOSITION
PRODUCTS - Titanium Dioxide, Silicon Dioxide, Carbon Dioxide, and traces of
incompletely burned carbon products.
SECTION VIII - SPILL LEAK AND DISPOSAL PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Use absorbent material to
collect and contain for salvage or disposal. Remove all sources of ignition and wear proper protection
equipment.
WASTE DISPOSAL METHOD: Review all Local, State and Federal regulations concerning health and
pollution be reviewed to determine approved disposal procedures.
SECTION IX - SPECIAL PROTECTION INFORMATION
EYES: Use chemical worker goggles.
SKIN: Washing at mealtime and end of shift is adequate. Remove contaminated clothing and shoes as soon as
practical and clean thoroughly before reuse.
INHALATION: Use respiratory protection unless local exhaust ventilation is adequate or air sampling data
show exposures are within TLV and PEL guidelines.
D.O.T. (49CFR 171.8) / E.P.A. (40 CFR 117) SPILL REPORTING INFO.:
HAZARDOUS SUBSTANCE - None.
CONCENTRATION OF
HAZARDOUS SUBSTANCES - N/A.
REPORTABLE QUANTITY OF
PRODUCT - N/A.
COMMENTS: Product contains no ingredient subject to D.O.T. or E.P.A. CERCLA/SARA environmental
release reporting regulations. See SECTION XI for additional SARA compliance information.
Product is an oil in the context of the U.S. CLEAN WATER ACT. Spills to U.S. surface waters, or to
watercourse or sewer leading to U.S. surface waters that cause a visible sheen must be reported to the National
Response Center.
(over)
SECTION X - ROUTINE HANDLING PRECAUTIONS
PROTECTIVE EQUIPMENT:
EYES: Use proper protection. Safety glasses as a minimum.
MOLDKOTE 1900-3 MATERIAL SAFETY DATA SHEET PAGE 17 OF 21
SKIN: Washing at mealtime and end of shift is adequate.
INHALATION: Use respiratory protection unless local exhaust ventilation is adequate or air sampling data
show exposures are within TLV and PEL Guidelines.
VENTILATION: LOCAL EXHAUST: RECOMMENDED. Mechanical (General).
SUITABLE RESPIRATORY: Organic vapor type.
OTHER PRECAUTIONS: These precautions are for room temperature handling. Use at elevated
temperatures may require added precautions. Good practice required that gross amounts of any chemical be
removed from the skin as soon as possible, especially before eating or smoking.
PRECAUTIONS TO BE TAKEN IN HANDLING & STORING:
Product is flammable. Use reasonable care and caution.
SECTION XI - COMMENTS
ADDITIONAL SARA REGULATORY COMPLIANCE INFORMATION
SEC. 312 HAZARD CLASS: IMMEDIATE, DELAYED, AND FIRE.
SEC. 313 NOTIFICATION: NOT APPLICABLE - EITHER NONE PRESENT OR NONE PRESENT IN
REGULATED QUANTITIES.
SUPPLEMENTAL STATE COMPLIANCE INFORMATION - CAS NO. & COMPONENT NAME
PENNSYLVANIA: 000682019 TETRAPROPYL ORTHOSILICATE
002157451 TETRA(2-METHOXYETHOXY)SILANE
005593704 TETRABUTYL TITANATE
064742898 NAPHTHA, PETROLEUM, LIGHT ALIPHATIC
MASSACHUSETTS: NO INGREDIENTS REGULATED BY MASSACHUSETTS RIGHT TO
KNOW LEGISLATION PRESENT.
NEW JERSEY: SAME AS PENNSYLVANIA ABOVE.
SECTION XII - SHIPPING INFORMATION
D.O.T. HAZARD NAME
(49CFR 172.101) - Naphtha.
D.O.T. HAZARD CLASS
(49CFR 172.101) - Flammable liquid.
PROPER SHIPPING NAME
(49CFR 172.101) - Flammable liquid NOS.
D.O.T. I.D. NO.
(49CFR 172.101) - UN 1993
DISCLAIMER OF LIABILITY
As the conditions or methods of use are beyond our control, we do not assume any responsibility and
expressly disclaim liability for any use of this material. Information contained herein is believed to be true
and accurate but all statements are made without warranty, express or implied, regarding the accuracy of
the information, the hazards connected with the use of the material or the results to be obtained from the
use thereof. It is the user's obligation to determine the conditions of safe use and the suitability of the
material for the user's purpose.
Prepared By: Joe Morales
F#170-21A
PRODUCT DATA
HASTINGS MSDS 1906
PLASTICS *REVISED 4/22/99
REPLACED 3/17/93
COMPANY
1704 Colorado Ave. Santa Monica, CA 90404 310-829-3449 FAX 310-828-6820
BACK TO INDEX
MOLDKOTE 1906
SECTION I - PRODUCT IDENTIFICATION
MANUFACTURER'S NAME - HASTINGS PLASTICS COMPANY
PRODUCT INFORMATION & SALES - (310) 829-3449
EMERGENCY PHONE NUMBER - (800) 424-9300
PRODUCT NAME - Moldkote
PRODUCT CODE NUMBER - 1906
CHEMICAL FAMILY - Vinyl
CHEMICAL NAME AND SYNONYMS - Vinyl
SECTION II - HAZARDOUS INGREDIENTS
ACGIH-PPM OSHA-PPM
COMPONENTS CAS # % TLV LEL PEL
TOLUENE 108-88-3 30-35 200 1.0 N/A
METHYL ETHYL KETONE 78-93-3 20-22 200 N/A N/A
METHYL ISOBUTYL KETONE 108-10-9 9-11 100 1.4 N/A
BUTYL CELLOSOLVE 111-76-2 1.85 50 1.1 N/A
ISOPROPYL ALCOHOL 67-63-0 0.23 400 2.0 N/A
ACETONE 67-64-1 5 750 N/A 750
M-75 64742-89-8 8 300 N/A N/A
XYLENE 1330-20-7 3-4 100 N/A 100
NORMAL BUTYL ACETATE 123-86-4 1-2 150 N/A 150
VINYL RESIN 9003-22-9 16 N/A N/A N/A
VINYL ACETATE 108-05-4 .08 See Section V
SECTION III - PHYSICAL DATA
APPEARANCE - Green liquid.
200 - 300/F.
BOILING POINT -
VAPOR DENSITY - Heavier than air.
SPECIFIC GRAVITY (Wt/Gal) - 7.46
PERCENT VOLATILE BY VOLUME - 9.57
EVAPORATION RATE - Slower than ether.
V.O.C. CONTENT Gms/Liter - 747
SECTION IV - FIRE AND HAZARD EXPLOSION DATA
- 24/F.
FLASH POINT
FLAMMABLE LIMITS - Unknown.
EXTINGUISHING MEDIA - Carbon dioxide, dry chemical, alcohol foam.
UNUSUAL FIRE AND EXPLOSION HAZARD - May form toxic materials upon burning:
carbon dioxide, carbon monoxide, and various
hydrocarbons.
MOLDKOTE 1600 MSDS PAGE 19 OF 21
SECTION V - HEALTH HAZARD DATA
THRESHOLD LIMIT VALUE - 100 ppm in air.
EFFECTS OF OVEREXPOSURE: No data available. Vinyl chloride has been listed as carcinogen in the
National Toxicology Program (NTP) Annual Report on Carcinogens, in International Agency for Research on
Cancer (IARC) monographs and by OSHA. This product contains less than 1 ppm of vinyl chloride monomer
and is exempt from the OSHA vinyl chloride standard CFR 29 Paragraph 1910.1017 under (a)(2) of the
standard. It is not anticipated to contribute to risk of adverse health effects at concentrations contained in this
product. This product may contain small amounts (<0.5%) of vinyl acetate, vapors of which have been shown
to cause tumors of the respiratory tract of laboratory animal in lifetime inhalation studies high exposure levels.
There is no evidence that it has caused cancer in humans. There should be minimal risk when used with
ventilation adequate to keep the atmospheric concentration of vinyl acetate below the recommended exposure
limits.
EMERGENCY & FIRST AID PROCEDURES: In case of eye contact, flush eyes with eye wash, or water for 5
- 10 minutes. Consult physician. In case of skin contact, wipe off material and wash contacted area.
SECTION VI - REACTIVITY DATA
STABILITY - Stable.
HAZARDOUS POLYMERIZATION - Will not occur.
CONDITIONS TO AVOID - Sparks, flame, and high temperatures.
HAZARDOUS DECOMPOSITION - Will react with strong oxidizing materials.
SECTION VII - SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Add solid absorbant scoop into
disposal container, solvent rinse, and hose down area.
WASTE DISPOSAL METHOD: Dispose of in accordance with local regulations.
SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION - Use approved respiratory equipment if vapor exceeds TLV.
EYE PROTECTION - Use safety glasses.
SECTION IX - SPECIAL PRECAUTIONS & STORAGE DATA
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Avoid flame. High temperature storage.
Also localized solvent vapor build-up. Ground equipment to eliminate danger of static electrical sparking. Do
not take internally, avoid prolonged contact, or inhalation.
SECTION X - REGULATORY INFORMATION
STATUS ON SUBSTANCE LISTS: The concentrations shown are maximum or ceiling levels (weight %) to
be used for calculations for regulations. Trade Secrets are indicated by "TS".
FEDERAL EPA
Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) requires
notification of the National Response of release of quantities of Hazardous Substances Equal to or greater than
the reportable quantities (RQs) in 40 CFR 302.4.
Components present in this product at a level which could require reporting under the statute are:
UPPER BOUND
CHEMICAL CAS NUMBER CONCENTRAION %
Acetone 67-64-1 5
Vinyl Acetate 108-05-4 0.5
MOLDKOTE 1600 MSDS PAGE 20 OF 21
Superfund Amendments and Reauthorization
Act of 1986 (SARA) Title III
requires emergency planning based on Threshold Planning Quantities (TPQs) and release reporting based on
Reportable Quantities (RQs) in 40 CFR 355 (used for SARA 302, 304, 311 and 312).
Components present in this product at a level which could require reporting under the statute are:
UPPER BOUND
CHEMICAL CAS NUMBER CONCENTRAION %
Vinyl Acetate 108-05-4 0.5
Superfund Amendments and Reauthorization
Act of 1986 (SARA) Title III
requires submission of annual reports of release of toxic chemicals that appear in 40 CFR 372 (for SARA 313).
This information must be included in all MSDs that are copied and distributed for this material.
Components present in this product at a level which could require reporting under the statute are:
UPPER BOUND
CHEMICAL CAS NUMBER CONCENTRAION %
Acetone 67-64-1 <2
STATE RIGHT-TO-KNOW
CALIFORNIA Proposition 65
None
MASSACHUSETTS Right-to-Know, Substance List (MSL) Hazardous Substances and Extraordinarily
Hazardous Substances on the MSL must be identified when present in products.
Components present in this product at a level which could require reporting under the statute are:
EXTRAODINARLY HAZARDOUS SUBSTANCES (=>0.0001%)
UPPER BOUND
CHEMICAL CAS NUMBER CONCENTRATION %
Vinyl Acetate 108-05-4 .05
HAZARDOUS SUBSTANCES (=>1%)
UPPER BOUND
CHEMICAL CAS NUMBER CONCENTRATION %
Acetone 67-64-1 <2
PENNSYLVANIA Right-to-Know, Substance List (MSL) Hazardous Substances and Extraordinarily
Hazardous Substances on the MSL must be identified when present in products.
Components present in this product at a level which could require reporting under the statute are:
HAZARDOUS SUBSTANCES (=>1%)
UPPER BOUND
CHEMICAL CAS NUMBER CONCENTRATION %
Acetone 67-64-1 <2
Toxic Substances Control Act(TSCA) STATUS:
The ingredients of this product are on the TSCA inventory.
MOLDKOTE 1600 MSDS PAGE 21 OF 21
SECTION X - SHIPPING INFORMATION
D.O.T. SHIPPING NAME - Coating solution.
D.O.T. I.D. NO. - UN 1139.
HAZARD CLASS - Flammable liquid.
DISCLAIMER OF LIABILITY
As the conditions or methods of use are beyond our control, we do not assume any responsibility
and expressly disclaim liability for any use of this material. Information contained herein is
believed to be true and accurate but all statements are made without warranty, express or implied,
regarding the accuracy of the information, the hazards connected with the use of the material or
the results to be obtained from the use thereof. It is the user's obligation to determine the
conditions of safe use and the suitability of the material for the user's purpose.
Prepared By: Joe Morales
F#170-21A
|