The MSDS format adheres to the standards and regulatory requirements
of the United States and may not meet regulatory requirements
in other countries.
DuPont Page 1
Material Safety Data Sheet
----------------------------------------------------------------------
"CONPOL" PROCESSING ADDITIVE RESIN ALL IN SYNONYM LIST CON001
CON001 Revised 23-APR-2004
----------------------------------------------------------------------
----------------------------------------------------------------------
CHEMICAL PRODUCT/COMPANY IDENTIFICATION
----------------------------------------------------------------------
Material Identification
"CONPOL" is a trademark of DuPont.
Tradenames and Synonyms
"CONPOL" 20S1
"CONPOL" 20S2
"CONPOL" 10S3
"CONPOL" 4R
"CONPOL" 4R11S1
"CONPOL" 10AF
"CONPOL" 10VE
Company Identification
MANUFACTURER/DISTRIBUTOR
DuPont Packaging & Industrial Polymers
1007 Market Street
Wilmington,DE 19898
PHONE NUMBERS
Product Information : 1-(800)-441-7515
Transport Emergency : 1-(800)-424-9300
Medical Emergency : 1-(800)-441-3637
----------------------------------------------------------------------
COMPOSITION/INFORMATION ON INGREDIENTS
----------------------------------------------------------------------
# Components
Material CAS Number %
ETHYLENE/METHACRYLIC ACID 25053-53-6 >80
COPOLYMER
NON-REGULATED ADDITIVES <20
Components (Remarks)
Material is not known to contain Toxic Chemicals under Section 313
of Title III of the Superfund Amendments and Reauthorization Act
of 1986 and 40 CFR part 372.
CON001 DuPont Page 2
Material Safety Data Sheet
----------------------------------------------------------------------
HAZARDS IDENTIFICATION
----------------------------------------------------------------------
Potential Health Effects
ADDITIONAL HEALTH EFFECTS
Before using "CONPOL" Processing Additive Resins, read the
bulletin on the safe handling of these polymers.
No information is available for this ethylene/methacrylic acid
copolymer with additives. Based on its similarity to other
polymers, this resin is predicted to have low toxicity.
INGESTION
Not a probable route of exposure. Toxicity is predicted to be low
for all types, but feeding tests have not been conducted.
SKIN
No data are available. However, based on experience with handling
these polymers, no unusual dermatitis problem is expected from
routine handling. Molten polymer contacting the skin will cause
thermal burns.
EYE
Mechanical irritation only.
INHALATION
Polymer is not respirable as sold. At processing temperatures
above 325 degress C, fumes irritating to the eyes, nose and throat
may be evolved. Exposure may result in redness, itching and
tearing of the eyes and soreness in the nose and throat together
with coughing.
Carcinogenicity Information
None of the components present in this material at concentrations
equal to or greater than 0.1% are listed by IARC, NTP, OSHA or ACGIH
as a carcinogen.
----------------------------------------------------------------------
FIRST AID MEASURES
----------------------------------------------------------------------
# First Aid
INHALATION
No specific intervention is indicated as the compound is not
likely to be hazardous by inhalation. Consult a physician if
necessary.
CON001 DuPont Page 3
Material Safety Data Sheet
(FIRST AID MEASURES - Continued)
If exposed to fumes from overheating or combustion, move to fresh
air. Consult a physician if symptoms persist.
SKIN CONTACT
The compound is not likely to be hazardous by skin contact but
cleansing the skin after use is advisable.
If molten material gets on skin, cool rapidly with cold water. Do
not attempt to remove material from skin. Obtain medical treatment
for thermal burn.
EYE CONTACT
In case of contact, immediately flush eyes with plenty of water
for at least 15 minutes. Call a physician.
INGESTION
Not a probable route. However, in case of accidental ingestion,
call a physician.
----------------------------------------------------------------------
FIRE FIGHTING MEASURES
----------------------------------------------------------------------
Flammable Properties
UNUSUAL FIRE, EXPLOSION HAZARDS The solid polymer can be
combusted only with difficulty. An electrostatic charge can
potentially build up when pouring pellets. Grounding of equipment
is recommended.
Hazardous gases/vapors produced in fire are carbon monoxide, and,
hydrocarbon oxidation products, including, organic acids,
aldehydes, alcohols, and, zinc, or, sodium oxides, oxides of
nitrogen.
Extinguishing Media
Water, Foam, Dry Chemical, CO2.
# Fire Fighting Instructions
Wear self-contained breathing apparatus (SCBA) and full protective
equipment.
CON001 DuPont Page 4
Material Safety Data Sheet
----------------------------------------------------------------------
ACCIDENTAL RELEASE MEASURES
----------------------------------------------------------------------
Safeguards (Personnel)
NOTE: Review FIRE FIGHTING MEASURES and HANDLING (PERSONNEL)
sections before proceeding with clean-up. Use appropriate
PERSONAL PROTECTIVE EQUIPMENT during clean-up.
Spill Clean Up
Recover undamaged and minimally contaminated material for reuse
and reclamation.
----------------------------------------------------------------------
HANDLING AND STORAGE
----------------------------------------------------------------------
Handling (Personnel)
See FIRST AID and PERSONAL PROTECTIVE EQUIPMENT SECTIONS.
Storage
Store in a cool dry place. Keep containers closed to
prevent contamination.
----------------------------------------------------------------------
EXPOSURE CONTROLS/PERSONAL PROTECTION
----------------------------------------------------------------------
# Engineering Controls
VENTILATION When hot processing this material, use local and/or
general exhaust ventilation to control the concentration of vapors
and fumes below exposure limits.
In cutting or grinding operations with this material, use local
exhaust to control the concentration of dust below exposure limits.
Personal Protective Equipment
EYE/FACE PROTECTION
Wear safety glasses. Wear coverall chemical splash goggles and/or
face shield when the possibility exists for eye and face contact
due to splashing or spraying of material. A full face mask
respirator provides protection from eye irritation.
RESPIRATORS
A NIOSH/MSHA approved air purifying respirator with an organic
vapor cartridge with a dust/mist canister may be permissible under
certain circumstances where airborne concentrations are expected
to exceed exposure limits. Protection provided by air purifying
respirators is limited. Use a positive pressure air supplied
respirator if there is any potential for an uncontrolled release,
exposure levels are not known, or any other circumstances where
air purifying respirators may not provide adequate protection.
CON001 DuPont Page 5
Material Safety Data Sheet
(EXPOSURE CONTROLS/PERSONAL PROTECTION - Continued)
PROTECTIVE CLOTHING
If there is potential for contact with hot/molten material, wear
heat resistant impervious clothing and footwear.
Exposure Guidelines
Exposure Limits
"CONPOL" PROCESSING ADDITIVE RESIN ALL IN SYNONYM LIST CON001
PEL (OSHA) : Particulates (Not Otherwise Regulated)
15 mg/m3, 8 Hr. TWA, total dust
5 mg/m3, 8 Hr. TWA, respirable dust
----------------------------------------------------------------------
PHYSICAL AND CHEMICAL PROPERTIES
----------------------------------------------------------------------
Physical Data
Melting Point : 80-100 C (176-212 F)
% Volatiles : Negligible
Solubility in Water : Negligible
Odor : Mild methacrylic acid
Form : Pellets
Color : White
Specific Gravity : NA
----------------------------------------------------------------------
STABILITY AND REACTIVITY
----------------------------------------------------------------------
Chemical Stability
Stable at normal temperatures and storage conditions.
Incompatibility with Other Materials
Incompatible or can react with oxidizing agents.
# Decomposition
Decomposes with heat.
Decomposition temperature: 325 C (617 F)
Hazardous gases or vapors can be released, including carbon
monoxide, and, hydrocarbon oxidation products, including, organic
acids, aldehydes, alcohols, and, zinc, or, sodium oxides, oxides
of nitrogen.
Polymerization
Polymerization will not occur.
CON001 DuPont Page 6
Material Safety Data Sheet
----------------------------------------------------------------------
ECOLOGICAL INFORMATION
----------------------------------------------------------------------
# Ecotoxicological Information
AQUATIC TOXICITY:
No information is available. Do not discharge to streams, ponds,
lakes or sewers.
----------------------------------------------------------------------
DISPOSAL CONSIDERATIONS
----------------------------------------------------------------------
Waste Disposal
Preferred options for disposal are (1) recycling, (2) incin-
eration with energy recovery, and (3) landfill. The high fuel
value of this product makes option 2 very desirable for material
that cannot be recycled. Treatment, storage, transportation, and
disposal must be in accordance with applicable federal,
state/provincial, and local regulations.
----------------------------------------------------------------------
TRANSPORTATION INFORMATION
----------------------------------------------------------------------
Shipping Information
DOT/IMO/IATA
Not Regulated.
----------------------------------------------------------------------
REGULATORY INFORMATION
----------------------------------------------------------------------
U.S. Federal Regulations
TSCA Inventory Status : In compliance with TSCA Inventory
requirements for commercial purposes.
State Regulations (U.S.)
STATE RIGHT-TO-KNOW
No substances on the state hazardous substances list, for the
states indicated below, are used in the manufacture of products on
this Material Safety Data Sheet, with the exceptions indicated.
SUBSTANCES ON THE PENNSYLVANIA HAZARDOUS SUBSTANCES LIST PRESENT
AT A CONCENTRATION OF 1 % OR MORE (0.01% FOR SPECIAL HAZARDOUS
SUBSTANCES)- None known.
WARNING - SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM- None known.
SUBSTANCES ON THE NEW JERSEY WORKPLACE HAZARDOUS SUBSTANCE LIST
PRESENT AT A CONCENTRATION OF 1% OR MORE (O.1% FOR SUBSTANCES
IDENTIFIED AS CARCINOGENS, MUTAGENS OR TERATOGENS)- None known
CON001 DuPont Page 7
Material Safety Data Sheet
----------------------------------------------------------------------
OTHER INFORMATION
----------------------------------------------------------------------
Additional Information
MEDICAL USE: CAUTION: Do not use in medical applications
involving permanent implantation in the human body. For other
medical applications see DuPont CAUTION Bulletin No. H-50102.
----------------------------------------------------------------------
The data in this Material Safety Data Sheet relates only to the
specific material designated herein and does not relate to use in
combination with any other material or in any process.
Responsibility for MSDS : T. P. PRICE
DUPONT PACKAGING & INDUSTRIAL POLYMERS
Address : CHESTNUT RUN PLAZA 713
WILMINGTON, DE 19880-0713
Telephone : 302-999-4664
# Indicates updated section.
This information is based upon technical information believed to be
reliable. It is subject to revision as additional knowledge and
experience is gained.
End of MSDS
|