V - Ace 2000
Basecoat
887 Line
P
PRODUCT DESCRIPTION:
V Ace 2000 Basecoats is an acrylic urethane system which is designed for use over various
plastic substrates. Does not need a primer over most rigid plastics.
R
System must be used with a clearcoat
Can be used over flexible substrates with the proper clearcoat
887C001 V Ace 2500 Rigid Clear Coat
O
887C002 V Ace 2650 Rigid Clear Coat
897C761 Planitto 761 Flexible Clear Coat
897C775 Planitto 775 Flexible Clear Coat
D
TECHNICAL DATA:
Mixing ratio by weight: 100:7:70
Basecoat: Hardener: Solvent Blend
Viscosity applied: 13 - 16 sec # 4 Ford
U
Coverage @ 1 mil Dry 350 sq ft
Recommended dry film thickness: 0.6 - 1.0 mils
% Volume solids sprayable 12%
Pot Life: 4 hrs
C
VOC 6.4 lbs
These are typical properties for the various colors. See individual product information sheets for product
specifications
T
Meets the following OEM specifications
Mitsubishi ES-X71222 PD3
Toyota TSH 3131G (1C)
Nissan NES M 5081 / M0141 / NDS0096302
SURFACE PREPARATION:
Suitable substrates: various rigid and flexible plastic parts
D
Rigid
ABS, PC/ABS, acrylic, nylon, and PC/PBT
Flexible
Polyalkylene terephthalate, some TPO's with adhesion promoter, and PVC
A
*Note: With the inconsistencies of substrates, consult your local SHERWIN鈥揥ILLIAMS Representative for
system recommendations and substrate testing.
T
1. Clean as required
2. Surface must be free from all foreign substances: degrease or power wash
Prepainted Substrates:
A
1. Recoatable with itself
2. Lightly scuff sand to slightly dull surface appearance
MIXING:
1. Stir or shake V Ace 2000 Basecoats thoroughly before mixing.
2. Mix by weight 100 parts V Ace 2000 to 7 parts 700 C 811 to 60 to 80 parts V-Ace Thinner
Blend
3. To application viscosity of 16 to 18 sec # 4 Ford Cup as determined by line trials
4. Stir thoroughly and strain.
APPLICATION:
1. For proper results use the following recommendations. Check equipment by applying V Ace
Basecoats to a test panel before using.
2. Apply 2 coats of V Ace Basecoats to achieve the recommended dry film thickness of 0.6 -
0.8 mils.
3. Flash V Ace Basecoats 3 to 5 minutes
4. Apply Clear Coat, V Ace 2500, V Ace 2650, Plannito 761, or Planitto 775 depending upon
specific plastic substrate
5. Flash Clear for 10 to 15 minutes
6. Bake 30 min at 180F part temperature
PRODUCT AT-A-GLANCE
PRODUCT V Ace 2000
USE
搂 Direct to properly cleaned plastics
搂 Same basecoat for ridged and flexible substrates
搂 Wet on wet application
SUITABLE SUBSTRATES
搂 Rigid
搂 ABS, PC/ABS, Acrylic, Nylon, PC/PBT
搂 Flexible
polyalkylene terephthalate,some TPO's with adhesion promoter, and PVC
搂
SURFACE PREPARATION
搂 Clean as required
搂 Surface must be free from all foreign substances: degrease or powder wash
MIXING
搂 Stir or shake V Ace 2000 Basecoats thoroughly before mixing.
搂 Mix by weight 100 parts V Ace 2000 to 7 parts 700 C 811 to 60 to 80 parts V-Ace Thinner
Blend
搂 To application viscosity of 16 to 18 sec # 4 Ford Cup as determined by line trials
搂 Stir thoroughly and strain.
APPLICATION
Time to
Apply 2 coats Clear Coat
3 - 5 minutes
NOTES
搂 Must be used with proper clear coat
PERSONAL PROTECTION
鈥? Read all label directions before use. 鈥? Wear a NIOSH approved dust particulate
鈥? Refer to MSDS for specific information. mask when sanding.
鈥? Wear a NIOSH approved organic vapor 鈥? Wear safety glasses, coveralls, and rubber
respirator when mixing and applying. gloves when using product.
漏2000 Sherwin-Williams Automotive Finishes Corp. Printed in USA AS2437
Cleveland, OH 44115 09/00
|