|-------------------------------------------------------|
| MATERIAL SAFETY DATA SHEET |
|-------------------------------------------------------|
|-------------------------------------------------------------------------|
| SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION |
|-------------------------------------------------------------------------|
PRODUCT NAME : KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
: 15300, 15305, 15310, 15313
UPC NUMBER
PRODUCT USE/CLASS : Cement Coating
MANUFACTURER: 24 HOUR EMERGENCY:
DAP INC. TRANSPORTATION: 1-800-535-5053 (352-323-3500)
2400 BOSTON STREET MEDICAL: 1-800-327-3874 (513-558-5111)
BALTIMORE, MD 21224
PREPARE DATE: 11/1/1999 GENERAL INFORMATION:
REVISION NO.: 6 DAP INC. : 1-888-DAP-TIPS (1-888-327-8477)
REVISION DATE: 05/31/2005
|-------------------------------------------------------------------------|
| SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS |
|-------------------------------------------------------------------------|
ITEM ------------ CHEMICAL NAME ------------- CAS NUMBER RANGE WT/WT %
---------------------------------------------------------------------------
01 Calcium carbonate 1317-65-3 20.0-30.0 %
02 Crystalline Silica 14808-60-7 10.0-20.0 %
03 Talc 14807-96-6 1.0-5.0 %
04 Titanium dioxide 13463-67-7 1.0-5.0 %
05 Ethylene Glycol Monopropyl Ether 2807-30-9 1.0-5.0 %
06 Diethylene Glycol Butyl Ether 112-34-5 1.0-5.0 %
07 Butyl Benzyl Phthalate 85-68-7 1.0-5.0 %
08 Carbon Black 1333-86-4 0.0-0.1 %
---------------------- EXPOSURE LIMITS -------------------
ACGIH OSHA COMPANY
ITEM TLV-TWA TLV-STEL PEL-TWA PEL-CEILING TLV-TWA SKIN
---------------------------------------------------------------------------
01 10 mg/m3dust N.E. 10 mg/m3dust N.E. N.E. NO
02 0.05 mg/m3* N.E. ** N.E. N.E. NO
03 2 mg/m3dust N.E. 10 mg/m3dust N.E. N.E. NO
04 10 mg/m3dust N.E. 15 mg/m3dust N.E. N.E. NO
05 N.E. N.E. N.E. N. E. N.E. NO
06 N.E. N.E. N.E. N. E. N.E. NO
07 N.E. N.E. N.E. N. E. N.E. NO
08 3.5 MGM3 N.E. 3.5 MGM3 N. E. N.E. NO
(See Section 16 for abbreviation legend)
* The 2001 ACGIH Threshold Limit Values for Chemical Substances and
Physical Agents lists the median Respirable Particulate Mass (RPM) point
for crystalline silica at 4.0 microns in terms of the particle's
aerodynamic diameter.
** 10 mg/m3 / (% SiO2 + 2): Both concentration and percent quartz for the
application of this limit are to be determined from the fraction passing a
size selector with the following characteristics
|-------------------------------------------------------------------------|
| Aerodynamic diameter (unit density sphere) | Percent passing selector |
|-------------------------------------------------------------------------|
|2 |90 |
|2.5 |75 |
|3.5 |50 |
|5.0 |25 |
|10 |0 |
|-------------------------------------------------------------------------|
(Continued on Page 2)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 2
|-------------------------------------------------------------------------|
| SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS |
|-------------------------------------------------------------------------|
Remaining ingredients are not considered hazardous per the OSHA Hazard
Communication Standard.
Listed Permissible Exposure Levels (PEL) are from the U.S. Dept. of Labor
OSHA Final Rule Limits (CFR 29 1910.1000); limits may vary between states.
|-------------------------------------------------------------------------|
| SECTION 3 - HAZARDS IDENTIFICATION |
|-------------------------------------------------------------------------|
EMERGENCY OVERVIEW: A thick white liquid with a mild sweet odor.
WARNING! HARMFUL OR FATAL IF SWALLOWED. Causes eye, skin, nose, throat and
respiratory tract irritation. May affect the brain or nervous system
causing dizziness, headache or nausea. Prolonged exposure to skin may
cause dermatitis.
POTENTIAL HEALTH EFFECTS:
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Irritates the eyes.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: Irritates the skin.
EFFECTS OF OVEREXPOSURE 没 INHALATION: Irritates the nose, throat and
respiratory tract. If you experience eye watering, headache or dizziness or
if air monitoring demonstrates vapor / mist levels are above applicable
limits, wear an appropriate, properly fitted respiratory protection during
use and after application or leave the area.
EFFECTS OF OVEREXPOSURE - INGESTION: If ingested this product may cause
nausea, vomiting and diarrhea.
EFFECTS OF OVER EXPOSURE - CHHRONIC HAZARDS
The International Agency for Research on Cancer (IARC)has determined that
crystalline silica in the form of quartz or cristobalite that is inhaled
from occupational sources is carcinogenic to humans (Group 1- carcinogenic
to humans). Refer to IARC Monograph 68, Silica, Some Silicates and Organic
Fibres (published in June 1997) in conjunction with the use of these
materials. The National Toxicology Program (NTP) classifies respirable
crystalline silica as known to be a human carcinogen. Refer to the 9th
Report on Carcinogens (2000). The American Conference of Governmental
Industrial Hygienists (ACGIH) classifies crystalline silica, quartz, as a
suspected human carcinogen (A2).
Breathing dust containing respirable crystalline silica may not cause
noticeable injury or illness even though permanent lung damage may be
occurring. Inhalation of dust may have the following serious chronic health
effects: Excessive inhalation of respirable dust can cause pneumoconiosis,
a respiratory disease, which can result in delayed, progressive, disabling
and sometimes fatal lung injury. Symptoms include cough, shortness of
breath, wheezing, non-specific chest illness and reduced pulmonary
function. Smoking exacerbates this disease. Individuals with pneumoconiosis
are predisposed to develop tuberculosis. There is some evidence that
(Continued on Page 3)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 3
|-------------------------------------------------------------------------|
| SECTION 3 - HAZARDS IDENTIFICATION |
|-------------------------------------------------------------------------|
breathing respirable crystalline silica or the disease silicosis is
associated with an increased incidence of significant disease endpoints
such as scleroderma (an immune system disorder manifested by fibrosis of
the lungs, skin and other internal organs) and kidney disease.
MEDICAL CONDITIONS WHICH MAY BE AGGRAVATED BY CONTACT: None known.
PRIMARY ROUTE(S) OF ENTRY: SKIN CONTACT INHALATION
|-------------------------------------------------------------------------|
| SECTION 4 - FIRST AID MEASURES |
|-------------------------------------------------------------------------|
EYE CONTACT: Flush with large quantities of water for at least 15 minutes.
Contact a physician immediately.
SKIN CONTACT: Wash with soap and water.
INHALATION: Remove to fresh air. Contact a physician immediately.
INGESTION: DO NOT INDUCE VOMITING. Contact a physician or Regional Poison
Control Center immediately.
COMMENTS: Call 1-800-327-3874 if irritation or complications arise from
any of the above routes of exposure.
|-------------------------------------------------------------------------|
| SECTION 5 - FIRE FIGHTING MEASURES |
|-------------------------------------------------------------------------|
FLASH POINT: > 200 F (93 C) LOWER EXPLOSIVE LIMIT: N.A.
(PENSKY-MARTENS C.C.) UPPER EXPLOSIVE LIMIT: N.A.
AUTOIGNITION TEMPERATURE: N.E.
EXTINGUISHING MEDIA: CO2 DRY CHEMICAL FOAM
UNUSUAL FIRE AND EXPLOSION HAZARDS: None known.
SPECIAL FIREFIGHTING PROCEDURES: Full protective equipment, including
self-contained breathing apparatus, is recommended to protect from
combustion products. Cool exposed containers with water.
|-------------------------------------------------------------------------|
| SECTION 6 - ACCIDENTAL RELEASE MEASURES |
|-------------------------------------------------------------------------|
SPILL OR LEAK PROCEDURES: Dike spill area. Absorb remaining liquid with
absorbent material and place into containers.
(Continued on Page 4)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 4
|-------------------------------------------------------------------------|
| SECTION 6 - ACCIDENTAL RELEASE MEASURES |
|-------------------------------------------------------------------------|
|-------------------------------------------------------------------------|
| SECTION 7 - HANDLING AND STORAGE |
|-------------------------------------------------------------------------|
HANDLING INFORMATION: KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE
INTERNALLY. Avoid skin and eye contact. Do not get on clothing. Avoid
breathing vapors, mist or dust. Use only in a well ventilated area. Use
only with adequate ventilation. Ensure fresh air entry during application
and drying by opening windows and doors. Keep container closed when not in
use. Wash thoroughly after handling.
STORAGE INFORMATION: Store away from caustics and oxidizers. Keep
containers tightly closed when not in use. Keep containers from excessive
heat and freezing. Do not store at temperatures above 120 degrees F(49 C).
Do not store near stoves or radiators. Do not store in direct sunlight.
OTHER PRECAUTIONS: Intentional misuse by deliberately concentrating and
inhaling vapors may be harmful or fatal. Provide fresh air such that
chemical odors cannot be detected during use and while drying.
|-------------------------------------------------------------------------|
| SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION |
|-------------------------------------------------------------------------|
ENGINEERING CONTROLS: Provide sufficient mechanical ventilation (local or
general exhaust) to maintain exposure below PEL and TLV. Vapors are heavier
than air and will collect in low areas. Check all low areas (basements,
sumps, etc.) for vapor before entering.
RESPIRATORY PROTECTION:
Dry sanding of dried product results in the generation of dust which
contains crystalline silica. Avoid exposure to dust by wearing an
appropriate, properly fitted, dust respirator during dry sanding. Follow
respiratory manufacturer's directions for respirator use.
If the 8 hour exposure limit or value is exceeded for
any component, use an approved NIOSH/OSHA respirator. Consult your safety
equipment supplier and the OSHA regulation, 29 CFR 1910.134 for respirator
requirements. A respiratory protection program that meets OSHA 1910.134 and
ANSI Z88.2 requirements must be followed whenever workplace conditions
warrant a respirator's use.
The National Institute for Occupational Safety and Health (NIOSH)
recommended permissible exposure limit of 50 micrograms respirable free
silica per cubic meter of air (0.05 mg/m3) as determined by a full shift
sample up to 10 hour working day, 40 hours per week.
EYE PROTECTION: Goggles or safety glasses with side shields.
SKIN PROTECTION: Solvent impervious gloves.
(Continued on Page 5)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 5
|-------------------------------------------------------------------------|
| SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION |
|-------------------------------------------------------------------------|
OTHER PROTECTIVE EQUIPMENT: Provide eyewash and liquid impervious apron
if body contact may occur.
HYGIENIC PRACTICES: Wash contaminated clothing before reuse.
|-------------------------------------------------------------------------|
| SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES |
|-------------------------------------------------------------------------|
BOILING RANGE : 212 F (100 C) VAPOR DENSITY : Is heavier than air
ODOR : N.A.
APPEARANCE : White liquid EVAPORATION RATE: Is slower than Butyl
SOLUBILITY IN H2O : Soluble Acetate
SPECIFIC GRAVITY : 1.57
VAPOR PRESSURE : N.A.
PHYSICAL STATE : Liquid
(See Section 16 for abbreviation legend)
|-------------------------------------------------------------------------|
| SECTION 10 - STABILITY AND REACTIVITY |
|-------------------------------------------------------------------------|
CONDITIONS TO AVOID: Excessive heat and freezing.
INCOMPATIBILITY: Strong oxidizers and caustics.
HAZARDOUS DECOMPOSITION PRODUCTS: Normal decomposition products, i.e. COx,
NOx
HAZARDOUS POLYMERIZATION: Will not occur under normal conditions.
STABILITY: This product is stable under normal storage conditions.
|-------------------------------------------------------------------------|
| SECTION 11 - TOXICOLOGICAL PROPERTIES |
|-------------------------------------------------------------------------|
No information available.
|-------------------------------------------------------------------------|
| SECTION 12 - ECOLOGICAL INFORMATION |
|-------------------------------------------------------------------------|
No Information Available.
(Continued on Page 6)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 6
|-------------------------------------------------------------------------|
| SECTION 12 - ECOLOGICAL INFORMATION |
|-------------------------------------------------------------------------|
|-------------------------------------------------------------------------|
| SECTION 13 - DISPOSAL CONSIDERATIONS |
|-------------------------------------------------------------------------|
WASTE MANAGEMENT/DISPOSAL: Dispose of according to Federal, State, and
Local Standards. Discarded material should be incinerated at a permitted
facility. Liquids cannot be disposed of in a landfill. Do not reuse empty
container. State and Local regulations/restrictions are complex and may
differ from Federal regulations. Responsibility for proper waste disposal
is with the owner of the waste.
EPA WASTE CODE - If discarded (40 CFR 261): None.
|-------------------------------------------------------------------------|
| SECTION 14 - TRANSPORTATION INFORMATION |
|-------------------------------------------------------------------------|
DOT PROPER SHIPPING NAME: Not Regulated by D.O.T.
DOT HAZARD CLASS: NONE
DOT UN/NA NUMBER: NONE PACKING GROUP: NONE
|-------------------------------------------------------------------------|
| SECTION 15 - REGULATORY INFORMATION |
|-------------------------------------------------------------------------|
U.S. FEDERAL REGULATIONS: AS FOLLOWS -
OSHA: Hazardous by definition of Hazard Communication Standard (29 CFR
1910.1200)
SARA SECTION 313:
This product contains the following substances subject to the reporting
requirements of Section 313 of Title III of the Superfund Amendments and
Reauthorization Act of 1986 and 40 CFR Part 372:
None
TOXIC SUBSTANCES CONTROL ACT:
This product contains the following chemical substances subject to the
reporting requirements of TSCA 12(B) if exported from the United States:
None
(Continued on Page 7)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 7
|-------------------------------------------------------------------------|
| SECTION 15 - REGULATORY INFORMATION |
|-------------------------------------------------------------------------|
NEW JERSEY RIGHT-TO-KNOW:
The following materials are non-hazardous, but are among the top five
components in this product:
|-------------------------------------------------------------------------|
| SECTION 15 - REGULATORY INFORMATION |
|-------------------------------------------------------------------------|
----------- CHEMICAL NAME ----------- CAS NUMBER
Calcium carbonate 1317-65-3
Acrylic polymer Proprietary
Nonasbestos tremolite 14567-73-8
Talc 14807-96-6
PENNSYLVANIA RIGHT-TO-KNOW:
The following non-hazardous ingredients are present in the product at
greater than 3%:
----------- CHEMICAL NAME ----------- CAS NUMBER
Calcium carbonate 1317-65-3
Acrylic polymer Proprietary
Nonasbestos tremolite 14567-73-8
Talc 14807-96-6
CALIFORNIA PROPOSITION 65:
WARNING: The chemical(s) noted below and contained in this product, are
known to the state of California to cause cancer:
----------- CHEMICAL NAME ----------- CAS NUMBER
Crystalline Silica 14808-60-7
INTERNATIONAL REGULATIONS: AS FOLLOWS -
CANADIAN WHMIS: This MSDS has been prepared in compliance with Controlled
Product Regulations except for use of the 16 headings.
CANADIAN WHMIS CLASS: Not determined.
|-------------------------------------------------------------------------|
| SECTION 16 - OTHER INFORMATION |
|-------------------------------------------------------------------------|
HMIS RATINGS - HEALTH: 1 FLAMMABILITY: 0 REACTIVITY: 0
PREVIOUS MSDS REVISION DATE: 07/15/2003
REASON FOR CHANGE: Change formulation.
VOC content: 146 g/L (9 - 10 %)
(Continued on Page 8)
--------------------------------------------------------------------------
Product Name: KWIK SEAL PLUS BASEMENT PAINT WITH MICROBAN
Revision Date: 05/31/2005 Page 8
|-------------------------------------------------------------------------|
| SECTION 16 - OTHER INFORMATION |
|-------------------------------------------------------------------------|
LEGEND: ACGIH - AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGIENISTS
N.A. - NOT APPLICABLE
N.E. - NOT ESTABLISHED
PEL - PERMISSIBLE EXPOSURE LIMIT
NTP - NATIONAL TOXICOLOGY PROGRAM
SARA - SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT OF 1986
STEL - SHORT TERM EXPOSURE LIMIT
TLV - THRESHOLD LIMIT VALUE(8 HR. TIME WEIGHTED AVERAGE OR TWA)
VOC - VOLATILE ORGANIC COMPOUND
NJRTK - NEW JERSEY RIGHT TO KNOW LAW
N.D. - NOT DETERMINED
MSDS# 79901
--------------------------------------------------------------------------
This data is offered in good faith as typical values and not as a product
specification. No warranty either expressed or implied, is hereby made.
The recommended industrial hygiene and safe handling procedures are
believed to be generally applicable. However, each user should review the
recommendations in specific context of the intended use and determine if
they are appropriate.
---------------------------------------------------------------------------
< End OF MSDS >
|