Transportation:
1-800-535-5053
1-352-3500
MATERIAL SAFETY DATA SHEET
______________________________________________________________________________
None
December 30, 2005
REVISION SUPERSEDES:
DATE: MSDS Number 00079975001
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
COMPANY INFORMATION
DAP Inc.
2400 Boston Street, Suite 200
Baltimore, MD 21224-4723
888-327-8477 (non-emergency matters)
PRODUCT INFORMATION
DAP STIKAROUNDS
PRODUCT IDENTIFIER:
PRODUCT Thermoplastic Adhesives
DESCRIPTION:
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration
Hazard Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian
Workplace Hazardous Materials Information System ingredient disclosure list. See Section 8 for
any additional exposure limit guidelines.
Not expected to be hazardous under normal conditions
HMIS RATING: HEALTH -- 0 FLAMMABILITY -- 1 REACTIVITY -- 0
See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective
equipment recommendations.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRY
EYE: Possible mild eye irritant. Any solid material may cause mechanical irritation.
SKIN: Possible mild skin irritant.
INHALATION: No irritation hazard in normal use.
Page 2 of 5
MATERIAL SAFETY DATA SHEET
______________________________________________________________________________
INGESTION: No hazard in normal use.
LONG-TERM (CHRONIC) HEALTH EFFECTS
TARGET ORGAN(S): None known
REGULATED CARCINOGEN STATUS:
Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or
OSHA listed carcinogens.
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: No medical conditions
affected by exposure.
SECTION 4: FIRST AID MEASURES
IF IN EYES: Immediately flush eyes with plenty of water for 10-15 minutes. Get medical attention
if irritation develops.
IF ON SKIN: For hot material, immediately immerse in or flush the affected area with large
amounts of cold water to dissipate heat. Cover with clean gauze and do not attempt to remove the
material yourself. Get prompt medical attention. Medical personnel: coat with mineral oil to soften
material for removal.
IF INHALED: These materials do not normally present a hazard if inhaled. Remove individual to
fresh air after an airborne exposure if any symptoms develop, as a precautionary measure. No
specific treatment is necessary since these materials are not likely to be hazardous by inhalation. If
exposed to excessive levels of dusts or fumes, remove to fresh air and get medical attention if cough
or other symptoms develop.
IF SWALLOWED: Do not induce vomiting. Seek medical attention if symptoms develop. Provide
medical care provider with this MSDS.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT: Greater than 400 degrees F / Cleveland (204 C)
AUTOIGNITION TEMPERATURE: Not established
LOWER EXPLOSIVE LIMIT (% in air): Not established
UPPER EXPLOSIVE LIMIT (% in air): Not established
EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon
dioxide.
UNUSUAL FIRE AND EXPLOSION Material will burn in a fire.
HAZARDS:
SPECIAL FIRE FIGHTING Persons exposed to products of combustion should
INSTRUCTIONS: wear self-contained breathing apparatus and full
protective equipment.
Page 3 of 5
MATERIAL SAFETY DATA SHEET
______________________________________________________________________________
SECTION 6: ACCIDENTAL RELEASE MEASURES
SPECIAL Allow molten material to solidify. Sweep up and place in
PROTECTION: container for disposal.
SECTION 7: HANDLING AND STORAGE
Handling: Prevent dusting.
Storage: Store in a cool, dry place.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
EYE PROTECTION: Wear safety glasses.
SKIN PROTECTION: Not normally required. Wear chemically resistant gloves
to prevent prolonged or repeated contact with solid
adhesive. When material is molten, wear thermally
insulated gloves to protect against thermal burns.
GLOVES: Not normally required.
RESPIRATORY No respiratory protection required under normal
PROTECTION: conditions of use.
VENTILATION: Hot melts should be used with good ventilation. At the
point of application and at the melter, local exhaust is
recommended.
EXPOSURE LIMITS:
Chemical Name ACGIH EXPOSURE LIMITS AIHA WEEL
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Solid
COLOR: NA
ODOR: Minimal
ODOR THRESHOLD: Not established
Page 4 of 5
MATERIAL SAFETY DATA SHEET
______________________________________________________________________________
SPECIFIC GRAVITY: Not established
pH: Not established
BOILING POINT (deg. C): Not established
FREEZING/MELTING POINT (deg. C): Not established
VAPOR PRESSURE (mm Hg): Not established
VAPOR DENSITY: Not established
EVAPORATION RATE: Not established
OCTANOL/WATER COEFFICIENT: Not established
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable under normal conditions.
CHEMICAL INCOMPATIBILITY: Not established
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION Not established.
PRODUCTS:
SECTION 11: TOXICOLOGICAL INFORMATION
CHEMICAL NAME LD50/LC50
TOXICOLOGY No additional health information available.
SUMMARY:
SECTION 12: ECOLOGICAL INFORMATION
OVERVIEW: No ecological information available
SECTION 13: DISPOSAL CONSIDERATIONS
To the best of our knowledge, this product does not meet the definition of hazardous waste under the
U.S. EPA Hazardous Waste Regulations 40 CFR 261. Dispose of in an approved landfill. Consult
your state, local or provincial authorities and your local waste vendor for more restrictive
requirements.
SECTION 14: TRANSPORTATION INFORMATION
Consult Bill of Lading for transportation information.
DOT: Not regulated
Page 5 of 5
MATERIAL SAFETY DATA SHEET
______________________________________________________________________________
SECTION 15: REGULATORY INFORMATION
FEDERAL REPORTING
EPA SARA Title III Section 313
Unless listed below, this product does not contain toxic chemical(s) subject to the reporting
requirements of section 313 of Title III of the Superfund Amendments and Reauthorization Act of
1986 (SARA) and 40 CFR part 72. EPA has advised that when a percentage range is listed the
midpoint may be used to fulfill reporting obligations.
Chemical Name CAS# %
WHMIS STATUS:
Not WHMIS controlled
STATE REPORTING
Proposition 65, The Safe Drinking Water and Toxic Enforcement Act of 1986:
This product does not contain known levels of any chemical known to the State of California to
cause cancer or reproductive harm.
SECTION 16: ADDITIONAL INFORMATION
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety
and Health Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the
Canadian Workplace Hazardous Materials Information System (WHMIS).
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP